Replacement Part List

M18™ FUEL™ 1/2" Super-Hawg
®
2709-20
G60A
54-10-2720
SEE PAGE 4
July 2015
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
16 06-82-7261 6-19 x .687 Pan Hd. Slt. Plast. T-15 Screw (6)
50 43-44-0705 Gasket (1)
61 06-82-5314 10-24 x 1/2" Pan Hd. Tapt. T-25 Screw (2)
68 06-82-7240 6-19 x .5 Pan Hd. Slt. Plast. T-15 Screw (2)
69 12-20-0077 Service Nameplate (1)
70 --------------- Right Handle Halve (Cover) (1)
72 45-30-1000 Rubber Slug (2)
73 --------------- Left Handle Halve (Support) (1)
74 42-42-0017 Forward/Reverse Shuttle (1)
75 06-82-5285 6-32 x .5 Pan Hd. Tapt. T-15 Screw (4)
76 06-82-1080 M3 x 14mm T-10 ST Screw (6)
77 --------------- Motor Cage Cover - Left (1)
78 --------------- Motor Cage Support - Right (1)
79 06-82-0130 6-32 x 5/16" Pan Hd. T-15 Machine Screw (2)
82 48-66-3280 Chuck Key (1)
94 23-16-0205 Motor Cage Assembly (1)
96 31-44-1095 Handle Assembly (1)
97 14-20-2709 Electronics Assembly
Contains: Stator, PCBA, On-Off Switch,
LED, Battery Connector Block (1)
98 16-01-2709 Rotor Assembly (1)
99 14-13-0055 Diaphragm Assembly with Needle Bearings (1)
100 43-72-0077 Key Holder Assembly (1)
105 42-55-3565 FUEL™ Contractor Bag - Large (1)
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
CATALOG NO.
MILWAUKEE TOOL

www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 1
STARTING
SERIAL NO.
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00

IMPORTANT!
To prevent damage to the High Voltage Wire Assembly, a com-
ponent in the Electronics Assembly #97, see service note on
page 4 prior to removing the Motor Cage Cover #77.
= #68, 06-82-7240
= #16, 06-82-7261
75
(4x)
77
73
74
76
(6x)
100
79
(2x)
82
105
50
99
98
61
(2x)
97
78
70
68
(2x)
69
16
(6x)
77
78
94
70
73
96
NOTE: As an aid when
installing Rotor, loosen
four rear screws on the
Motor Cage Assy.
Slide Rotor into
Stator and firm-
ly seat rear ball
bearing in motor
cage cavity. Retighten
the four screws.
Both motor cage halves have a
raised rib that is to be firmly
seated into slots on each
side of the stator
assembly.
SCREW TORQUE CHART
Seat Torque
Item Part Number (Kg./cm.) (In./lbs.)
1 06-75-3155 140-160 122-139
4 06-82-5411 35-50 30-43
15 05-88-9915 60-65 52-56
16 06-82-7261 For Shift Hub 8-12 7-10
16 06-82-7261 For Handle 12-17 10-14
24 05-88-0510 30-45 26-39
30 06-82-5360 75-86 65-74
61 06-82-5314 46-58 40-50
68 06-82-7240 12-17 10-14
75 06-82-5285 12-17 10-14
76 06-82-1080 7-13 6-11
79 06-82-0130 10-15 8-13