Service and Repairs

12
22
14
17 16(5x)
11
18
16(2x)
20
63
33
(5x)
34
29
32
7(2x)
31
42
(4x)
13(6x)
10
9
2
4
5
3
1
6(2x)
2 16
17 22
60
10 11
15 18
61
12 13
14
62
1 32
33 34
64
47
15
3 4 5
6 7 31
65
13
3
1
2
4
42
Alternate the
tightening pattern
for gearcase
screws #42 as
shown.
Seat torque to
be 19.5 in/lbs
(21.5 kg/cm)
Order is 1,2,3,4
than 1,2,3,4 again
Magnet
Ring Motor Band #20
Motor Assembly #63 Lobes
When replacing Motor
Assembly #63, be sure to
reuse Motor Band #20.
Place the motor band flush
to the end of the motor
canister as shown. Be sure
not to cover motor vents.
IMPORTANT:
Do not attempt to make
adjustments to the magnet
ring or any other compo-
nent on the motor assem-
bly.
When reinstalling a motor
assembly, be sure to orient the ‘lobes’ of the motor mount at the 12:00 and
6:00 position prior to placing the motor assembly in Left Rear Handle #2.
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
42 05-88-0400 M4 x 20mm Fillister Hd. T-20 Screw 4
47 06-75-0025 Blade/Backing Pad Screw 1
60 31-44-1057 Rear Handle Assembly 1
61 14-20-2626 Switch/Electronics Assembly 1
62 14-67-0130 Terminal Block Plate Assembly 1
63 14-50-0707 Motor Assembly 1
64 14-38-2000 Front Housing Assembly 1
65 14-29-2626 Gearcase Assembly 1
66 48-55-3500 Carrying Case 1
MILWAUKEE TOOL • www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 2
BULLETIN NO.
54-22-2601
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 --------------- Front Housing - Left 1
2 --------------- Rear Handle - Left 1
3 44-10-0225 Quick Release Lever 1
4 05-88-0045 M4 x 0.7 x 8mm Pan Hd. Taptite Phillips Scr 1
5 42-70-0510 Clip 1
6 34-40-0077 Rubber O-Ring 2
7 42-40-0125 Nylon Bushing 2
9 45-24-1030 Switch Slide 1
10 --------------- On-O󰀨 Switch 1
11 --------------- Terminal Block 1
12 44-66-0392 Terminal Block Plate 1
13 43-86-0005 Rubber Isolators 6
14 45-30-1000 Silicone Slug 2
15 --------------- LED Assembly 1
16 06-82-1080 M3 x 14mm Pan Hd. Plastite T-10 Screw 7
17 10-20-2743 Warning Label 1
18 --------------- PCBA 1
20 42-16-0450 Motor Band (Rubber) 1
22 --------------- Rear Handle - Right 1
29 45-88-0088 Washer 1
31 44-60-0605 5.0 x 26mm Pin 1
32 --------------- Front Housing - Right 1
33 06-82-2385 M2.6 x 14mm Pan Hd. Plastite T-8 Screw 5
34 12-20-2638 Service Nameplate 1
CATALOG NO. 2626-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M18™ MULTI-TOOL
STARTING
SERIAL NO.
DATE
Oct. 2019
WIRING INSTRUCTION
F40B
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
See Page Two
54-22-2600
66
= Part number change from
previous service parts list.

