Replacement Parts List

2567-20
M12™ FUEL 3/8" HIGH SPEED RATCHET
Oct. 2020
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
2 45-98-0020 Yoke (1)
3 42-40-0017 Bushing (1)
4 36-17-0111 Crankshaft (1)
5 --------------- Yoke Housing with Needle Bearings (1)
6 44-60-0890 Drive Pin (1)
7 --------------- Carrier (1)
8 --------------- Planetary Gears (3)
9 --------------- Ring Gear (1)
10 --------------- Washer (1)
13 44-66-1006 Motor Plate (1)
14 05-84-0205 M2.5 x 31mm Skt. Hd. Hex Drive Screw (3)
15 006-82-2310 M3 x 8mm Pan Hd. Taptite T-10 Screw (1)
16 05-81-0594 M4 x 14mm Flat Hd. ST T-20 Screw (4)
17 12-20-2513 Service Nameplate (1)
18 05-71-0017 M4 x 10mm Pan Hd. ST T-20 Screw (5)
19 --------------- Right Housing Halve - Cover (1)
20 --------------- Left Housing Halve - Support (1)
21 44-60-0575 Spring Pin (1)
22 42-42-0119 Switch Lock-Out (1)
23 10-20-4419 Fuel Gauge Label (1)
24 44-10-0740 Switch Paddle (1)
30 --------------- 3/8" Anvil w/ Standard Shift Knob (1)
31 --------------- Friction Plate (1)
54-47-2565
REVISED BULLETIN
BULLETIN NO.
WIRING INSTRUCTION
DATE
CATALOG NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
SERIAL
NUMBER
EXAMPLE:
Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
0
00
L83A
See Pages 2 and 3
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 1
NOTE: Spring Pin (21)
and Switch Paddle (24)
must be removed in
order to access Screw
(18). See additional
note to the left.
18
21
24
6
5
3
4
7
8
(3x)
9
122
10
103
16
(4x)
19
18
(5x)
17
104
13
15
104
22
104
14
(3x)
20
24
21
121
2
30
31
32
40
31
42
30 31
32
101
40 31
42
124
5
6
102
7 8
9 10
106
16 17 18 19
20 21 22 23
105
23
FIG. NOTES
17,19 Prior to installing a new nameplate or label,
23 apply isopropyl alcohol to handle cover with
a clean, lint free applicator and allowed to dry.
21 Use a thin blunt punch with the same OD or a
  similiartoollikeanishingnailwithsameOD
and pointed tip ground down to remove spring
pin from the handle halves and switch paddle.
As an aid, be sure to prop up that corner
end of ratchet to support tapping out of the
spring pin. When reinstalling pin, align holes
and carefully press or tap the pin in place.
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
32 --------------- Retaining Ring (1)
40 --------------- 3/8" Anvil w/ Tall Shift Knob (Optional) (1)
42 --------------- Retaining Ring (1)
101 42-06-0138 3/8" Anvil Service Kit-Standard (1)
102 14-46-2560 Yoke Housing Service Kit (1)
103 16-01-2560 Rotor Service Assembly (1)
104 14-20-2560 Electronics Service Assembly (1)
105 31-44-2560 Housing Service Kit (1)
106 28-23-2500 Gear Set Service Kit (1)
121 42-55-2561 Contractor Bag (Optional, Accessory) (1)
122 49-16-2567 Rubber Boot (Optional, Accessory) (1)
124 49-06-2567 3/8" Anvil Service Kit-Tall (Optional, Accy.) (1)
SERVICE PARTS LIST