Service Parts List S/N K85A

1a
1b
1a
1b
1
6
7(3x)
8
9
10
33
2
4
5
31
11(3x)
15(3x)
16
17
18
20
27
23
32
19(3x)
26
24
14
32
25
34
22(4x)
21(4x)
21 22 23
24 25 34
30
NOTE: Spring Pin (25)
and Switch Paddle (26)
must be removed in
order to access Screw
(22). See additional
note below.
22
25
26
35
NOTE: Add a drop of
Blue Loctite 243 to
threads of four screws
(21) prior to installing.
2560-20
M12™ FUEL 3/8" LONG REACH RATCHET
June 2019
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 42-06-2557 3/8" Anvil Service Kit (1)
1a --------------- Friction Plate (1)
1b --------------- Retaining Ring (1)
2 45-98-0065 Yoke (for 3/8" and 1/2" ratchet) (1)
4 42-40-0985 Bushing (for 3/8" and 1/2" ratchet) (1)
5 36-17-0115 Crank Shaft (for 3/8" and 1/2" ratchet) (1)
6 28-23-1005 Carrier Assembly (for 3/8" & 1/2" ratchet) (1)
7 32-62-0615 Planet Gear (for 3/8" & 1/2" ratchet) (3)
8 45-88-2035 Washer (1)
9 32-65-0405 Ring Gear (for 3/8" & 1/2" ratchet) (1)
10 44-66-0047 Motor Holder (1)
11 05-81-0105 M3 x 10mm Flat Hd. Machine T-10 Screw (3)
14 42-40-0210 Bushing (1)
15 06-82-2310 M3 x 8mm Pan Hd. Tapt. T-10 Screw (3)
16 44-86-1405 Bearing Plate (1)
17 02-04-0303 Ball Bearing (1)
18 44-66-1008 Motor Plate (1)
19 05-84-0200 M2.5 x 31mm Socket Hd. Hex Drive Scr. (3)
20 05-55-0047 Hex Nut (1)
21 05-81-0592 M4 x 6mm Flat Hd. T-15 Machine Screw (4)
22 06-82-3002 M3 x 10mm Pan Hd. Tapt. T-10 Screw (4)
23 --------------- Housing Cover - Right Housing Halve (1)
24 --------------- Housing Support - Left Housing Halve (1)
25 44-60-0575 Spring Pin (1)
26 44-10-0740 Switch Paddle (1)
27 42-42-0033 Switch Lock-Out (1)
30 31-44-0523 Housing Kit (1)
31 14-46-0474 3/8" Yoke / Beam / Gearcase Assembly (1)
32 14-20-0127 Electronics Assy. (for 1/4" & 3/8" ratchet) (1)
33 16-01-1035 Rotor Assembly (for 3/8" ratchet) (1)
34 12-20-2560 Service Nameplate (1)
35 42-55-2559 Zippered Tool Case (1)
36 42-04-0800 3/8" to 1/4" Adapter (Not Shown) (1)
37 49-16-2560 Rubber Boot (Optional, Acc) (Not Shown) (1)
54-47-0455
REVISED BULLETIN
SERVICE PARTS LIST
BULLETIN NO.
WIRING INSTRUCTION
DATE
CATALOG NO.
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
SERIAL
NUMBER
EXAMPLE:
Component Parts
(Small #) Are Included
When Ordering Assy.
(Large #).
0
00
K85A
See Pages 2 and 3
FIG. NOTES
23,34 Prior to installing a new service nameplate, apply isopropyl
alcohol to the handle cover with a clean, lint free applicator
and allowed to dry.
25 Use a thin blunt punch with the same OD or a similiar tool like
  anishingnailwiththesameODandthepointedtipground 
down to remove spring pin from the handle halves and switch
paddle. As an aid, be sure to prop up that corner end of
ratchet to support the tapping out of the spring pin. When
reinstalling pin, align the holes and carefully press or tap the
pin in place.
FIG. LUBRICATION
(Type 'E' Grease, No. 49-08-4122):
5 Apply a moderate coating of grease to the small cylindrical
surface that goes into driver bushing and to the large cylindri-
cal surface that is surrounded by the two needle bearings.
6 Apply a moderate coating of grease to the three axles of the
carrier assembly prior to installing the planet gears.
8 Apply a light coat of grease to the surface of the washer.
9,33 Apply a heavy coating of grease to the inside diameter gear
teeth of the ring gear and the teeth of the motor pinion.
MILWAUKEE TOOL
l
www.milwaukeetool.com
13135 W. LISBON RD., BROOKFIELD, WI 53005
Drwg. 2