OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. No de cat. 2426-20 M12™ CORDLESS MULTI-TOOL OUTIL POLYVALENT SANS FIL M12™ HERRAMIENTA MÚLTIPLE INALÁMBRICA M12™ TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR. PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. •Remove any adjusting key or wrench before turning the power tool on.
•Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire. •When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. •Under abusive conditions, liquid may be ejected from the battery; avoid contact.
Selecting speed To set the maximum speed, rotate the speed dial. Set the speed dial to "2" for the lowest speed (5000 OPM). Set the speed dial to "12" for the highest speed (20,000 OPM). MAINTENANCE WARNING To reduce the risk of injury, always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs. Starting/Stopping 1.
RÈGLES DE SÉCURITÉ GÉNÉRALES RELATIVES AUX OUTILS ÉLECTRIQUES AVERTISSEMENT LIRE TOUTES LES RÈGLES ET INSTRUCTIONS DE SÉCURITÉ. Ne pas suivre l’ensemble des règles et instructions peut entraîner une électrocution, un incendie ou des blessures graves. Conserver les règles et les instructions à des fins de référence ultérieure. Le terme «outil électrique» figurant dans les avertissements cidessous renvoie à l’outil électrique à alimentation par le réseau (à cordon) ou par batterie (sans fil).
Changement d’accessoire 1. Retirer le bloc-piles. 2. Placer l’outil à l’envers sur une surface plane. 3. Utiliser la clé hexagonale pour retirer le boulon d’accessoire. 4. Retirer la bride extérieure ainsi que tout accessoire et l’adaptateur. 5. Nettoyer le boulon, les brides, l’adaptateur et les accessoires pour en enlever la saleté et les débris. 6. Placer l’adaptateur (au besoin), l’accessoire, la bride extérieure et le boulon sur l’outil.
ENTRETIEN ACCESOIRES AVERTISSEMENT Pour minimiser les risques de blessures corporelles, débranchez le chargeur et retirez la batterie du chargeur ou de l’outil avant d’y effectuer des travaux d’entretien. Ne démontez jamais l’outil, la batterie ou le chargeur. Pour toute réparation, consultez un centre de service MILWAUKEE accrédité. AVERTISSEMENT Retirez toujours la batterie avant de changer ou d’enlever les accessoires.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA ADVERTENCIA LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD. Si no sigue todas las advertencias e instrucciones, se pueden provocar una descarga eléctrica, un incendio o lesiones graves. Guarde todas las advertencias e instrucciones para consultarlas en el futuro.
Cambio de accesorios 1. Retire la batería. 2. Coloque la herramienta boca abajo sobre una superficie plana. 3. Use la llave hexagonal para retirar el perno accesorio. 4. Quite la brida exterior, cualquier otro accesorio y adaptador. 5. Limpie la suciedad y los residuos del perno, las bridas, el adaptador y los accesorios. 6. Coloque el adaptador (si es necesario), el accesorio, la brida exterior y el perno sobre la herramienta. Determine la necesidad de un adaptador utilizando la tabla.
GARANTÍA LIMITADA - E.U.A. Y CANADÁ MANTENIMIENTO ADVERTENCIA Para reducir el riesgo de una lesión, desconecte siempre la herramienta antes de darle cualquier mantenimiento. Nunca desarme la herramienta ni trate de hacer modificaciones en el sistema eléctrico de la misma. Acuda siempre a un Centro de Servicio MILWAUKEE para TODAS las reparaciones. ADVERTENCIA Para reducir el riesgo de una explosión, no queme nunca una batería, aun si está dañada, “muerta” o completamente descargada.
UNITED STATES - MILWAUKEE Service MILWAUKEE prides itself in producing a premium quality product that is NOTHING BUT HEAVY DUTY®. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, or you would like to locate the factory Service/Sales Support Branch or authorized service station nearest you, please call... 1-800-SAWDUST (1.800.729.3878) Monday-Friday 7:00 AM - 6:30 PM Central Time or visit our website at www.milwaukeetool.