OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. / No de cat. 2461-20, 2462-20, 2463-20 M12™ CORDLESS IMPACT WRENCHES AND IMPACT DRIVER CLÉS À CHOCS ET VISSEUSE M12™ LLAVES DE IMPACTO E IMPULSOR DE IMPACTO DE M12™ WARNING To reduce the risk of injury, user must read and understand operator's manual. AVERTISSEMENT Afin de réduire le risque de blessures, l'utilisateur doit lire et bien comprendre le manuel.
GENERAL POWER TOOL SAFETY WARNINGS all safety warnings, instrucWARNING Read tions, illustrations and specifica- •Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. •Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. •Dress properly. Do not wear loose clothing or jewelry.
•When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire. •Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help.
ASSEMBLY OPERATION Recharge only with the charger To reduce the risk of injury, always WARNING specified WARNING wear for the battery. For speproper eye protection marked cific charging instructions, read the operator’s to comply with ANSI Z87.1. manual supplied with your charger and battery. When working in dusty situations, wear appropriate respiratory protection or use an OSHA Removing/Inserting the Battery To remove the battery, push in the release buttons compliant dust extraction solution.
SERVICE - UNITED STATES Impacting Techniques 1-800-SAWDUST (1.800.729.3878) The longer a bolt, screw, or nut is impacted, the tighter it will become. To help prevent damaging the fasteners or workpieces, avoid excessive impacting. Be particularly careful when impacting smaller fasteners because they require less impacting to reach optimum torque. Practice with various fasteners, noting the length of time required to reach the desired torque. Check the tightness with a hand-torque wrench.
RÈGLES DE SÉCURITÉ GÉNÉRALES RELATIVES AUX OUTILS ÉLECTRIQUES Lire toutes les consignes AVERTISSEMENT de sécurité, consignes, DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. This warranty applies to product sold in the U.S.A. and Canada only.
•Porter l’équipement de protection individuel requis. Toujours porter une protection oculaire. Selon les conditions, porter aussi un masque antipoussières, des bottes de sécurité antidérapantes, un casque protecteur ou une protection auditive afin de réduire les blessures. •Empêcher les démarrages accidentels. S’assurer que la gâchette est en position d’arrêt avant de brancher l’outil à une source de courant, d’insérer la batterie, de le ramasser ou de le transporter.
RÈGLES DE SÉCURITÉ SPÉCIFIQUES POUR CLÉS À CHOCS/VISSEUSE PICTOGRAPHIE Volts •Lorsque l’outil électrique est utilisé pour un travail risquant de mettre le dispositif de fixation en contact avec des fils électriques cachés, tenez l’outil par les surfaces de prise isolées. Le contact d’un dispositif de fixation avec un fil sous tension « électrifie » les pièces métalliques exposées de l’outil et peut électrocuter l’utilisateur. •Porter des protecteurs d’oreille.
MONTAGE DE L'OUTIL Ne recharger la batterie AVERTISSEMENT qu’avec le chargeur spéci- MANIEMENT Afin de minimiser le risque AVERTISSEMENT de blessures, toujours fié. Pour les instructions de charge spécifiques, porter la protection oculaire appropriée certifiée lire le manuel d’utilisation fourni avec le chargeur conforme à la norme ANSI Z87.1. et les batteries.
Nettoyage Démarrage, arrêt et contrôle de vitesse Ces outils peuvent être utilisés à n’importe quelle vitesse entre 0 et le plein régime. 1. Pour mettre l’outil en marche, appuyez sur la détente. N.B. : LED allume quand la détente est tirée. 2. Pour varier la vitesse de rotation, il s’agit simplement d’augmenter ou de diminuer la pression sur la détente. Plus la détente est enfoncée, plus la vitesse de rotation est grande. 3. Pour arrêter l’outil, relâchez la gâchette.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA Lea todas las advertencias ADVERTENCIA de seguridad, instrucciones, L’ACCEPTATION DES RECOURS EXCLUSIFS DE RÉPARATION ET DE REMPLACEMENT DÉCRITS DANS LES PRÉSENTES EST UNE CONDITION DU CONTRAT D’ACHAT DE TOUT PRODUIT MILWAUKEE. SI VOUS N’ACCEPTEZ PAS CETTE CONDITION, VOUS NE DEVEZ PAS ACHETER LE PRODUIT.
•Dé mantenimiento a las herramientas eléctricas y accesorios. Verifique que no haya desalineación, amarre de partes móviles, partes rotas o alguna otra condición que pueda afectar el funcionamiento de la herramienta eléctrica. Si se daña, asegúrese de que la herramienta eléctrica sea reparada antes de que se utilice. Muchos accidentes son ocasionados por herramientas eléctricas con mantenimiento deficiente. •Mantenga las herramientas de corte afiladas y limpias.
MANTENIMIENTO DESCRIPCION FUNCIONAL •Lleve su herramienta eléctrica a servicio con un técnico calificado que use únicamente piezas de reemplazo idénticas. Esto asegurará que la seguridad de la herramienta eléctrica se mantenga. •Nunca dé servicio a baterías dañadas. Únicamente el fabricante o proveedores de servicio autorizados deben dar servicio a las baterías. Cat. No. 2462-20 4 3 REGLAS ESPECIFICAS DE SEGURIDAD PARA LLAVES DE IMPACTO E IMPULSOR DE IMPACTO 5 2 1 1. Gatillo 2.
ENSAMBLAJE la batería sólo con ADVERTENCIA Recargue el cargador especificado OPERACION Con el fin de minimizar el ADVERTENCIA riesgo de lesiones, siempre para ella. Para instrucciones específicas sobre utilice la protección de ojos adecuada indicada cómo cargar, lea el manual del operador sumin- para cumplir con lo dispuesto en la norma ANSI istrado con su cargador y la batería. Z87.1.
Arranque, paro y control de velocidad Limpieza Estas herramientas pueden operarse a cualquier velocidad entre 0 y plena marcha. 1. Para accionar la herramienta, oprima el gatillo. NOTA: Las vueltas luz LED en cuando el disparador se tira. 2. Para variar la velocidad de operación, simplemente aumente o disminuya la presión del gatillo. Cuanto más se oprima el gatillo, mayor será la velocidad. 3. Para detener la herramienta, suelte el gatillo. Limpie el polvo y suciedad de las ventilas.
LA ACEPTACIÓN DE LOS REMEDIOS EXCLUSIVOS DE REPARACIÓN Y REEMPLAZO AQUÍ DESCRITOS ES UNA CONDICIÓN DEL CONTRATO PARA LA COMPRA DE TODO PRODUCTO DE MILWAUKEE. SI USTED NO ACEPTA ESTA CONDICIÓN, NO DEBE COMPRAR EL PRODUCTO.