OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. No de cat. 2445-20 M12™ CORDLESS JIG SAW SCIE SAUTEUSE M12™ SIERRA CALADORA DE M12™ TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR. PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. •Remove any adjusting key or wrench before turning the power tool on.
ASSEMBLY Using the anti-splinter device The anti-splinter device helps Fig. 3 stabilize the workpiece and Anti-splinter reduce workpiece splinter. 1. Remove the battery pack. device 2. Slide the anti-splinter device onto the shoe. Make sure the anti-splinter device is Shoe installed flush with the bottom of the shoe. NOTE: Do not use the antisplinter device when making bevel/angle cuts. WARNING Recharge only with the charger specified for the battery.
MAINTENANCE WARNING To reduce the risk of injury, ACCESSORIES WARNING Always remove battery pack before changing or removing accessories. Only use accessories specifically recommended for this tool. Others may be hazardous. always unplug the charger and remove the battery pack from the charger or tool before performing any maintenance. Never disassemble the tool, battery pack or charger. Contact a MILWAUKEE service facility for ALL repairs.
RÈGLES DE SÉCURITÉ GÉNÉRALES RELATIVES AUX OUTILS ÉLECTRIQUES AVERTISSEMENT LIRE TOUTES LES RÈGLES ET INSTRUCTIONS DE SÉCURITÉ. Ne pas suivre l’ensemble des règles et instructions peut entraîner une électrocution, un incendie ou des blessures graves. Conserver les règles et les instructions à des fins de référence ultérieure. Le terme «outil électrique» figurant dans les avertissements cidessous renvoie à l’outil électrique à alimentation par le réseau (à cordon) ou par batterie (sans fil).
SPECIFICATIONS No de Volts Cycles Cat. cd par minute 2445-20 12 0 - 2 800 PICTOGRAPHIE Longueur de course 19 mm (3/4") Cycles par minute à vide (SPM) Tension CD seul. Underwriters Laboratories, Inc. États-Unis et Canada Réglage du patin Le patin peut être incliné jusqu’à 45° dans l’une ou l’autre direction et déplacé vers l’avant ou vers l’arrière. Utiliser l’appareil d’anti-craquer quand le soulier est perpendiculaire à la lame. 1. Retirez la batterie. 2.
ENTRETIEN AVERTISSEMENT Pour minimiser les risques d’explosion, choc électrique et dommages à vos biens, lorsque vous effectuez une coupe en plongée, inspectez toujours l’aire de coupe pour y déceler la présence de fils électriques ou de canalisations. AVERTISSEMENT Pour minimiser les risques de blessures corporelles, débranchez le chargeur et retirez la batterie du chargeur ou de l’outil avant d’y effectuer des travaux d’entretien. Ne démontez jamais l’outil, la batterie ou le chargeur.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA ADVERTENCIA LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD. Si no sigue todas las advertencias e instrucciones, se pueden provocar una descarga eléctrica, un incendio o lesiones graves. Guarde todas las advertencias e instrucciones para consultarlas en el futuro.
Cómo instalar cuchillas Utilice solamente cuchillas para sierras caladoras de vástagos en T. 1. Extraiga la batería. 2. Firmemente alternar de tensión Quik-Lok a fondo y sujétela en su posición. 3. Ajuste la cuchilla en la acanaladura del rodillo de soporte y empújela a fondo firmemente en el percutor; la orejeta de la cuchilla deberá encontrarse en el percutor. 4. Suelte la palanca de tensión Quik-Lok y la cuchilla quedará sujeta de forma automática. 5.
Técnicas de corte especiales 1. Cortes rectos – Para obtener un corte perfectamente recto, sujete un pedazo de madera en calidad de guía a lo largo de la pieza de trabajo o use una guía de corte. 2. Cortes en bisel – ajuste la zapata al ángulo correcto (consulte la sección “Como ajustar la zapata”). 3. Corte de chapas metálicas – las chapas metálicas pueden vibrar durante el corte. Para minimizar la vibración, sujete la pieza de trabajo a una base de madera.
UNITED STATES MILWAUKEE Service MILWAUKEE prides itself in producing a premium quality product that is NOTHING BUT HEAVY DUTY®. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, or you would like to locate the factory Service/Sales Support Branch or authorized service station nearest you, please call... Additionally, we have a nationwide network of authorized Distributors ready to assist you with your tool and accessory needs.