Assembly and Installation Instructions

ManualsBrandsMillwood Pines ManualsLantern Outdoor Wall LightingShirley Dualux® Outdoor Wall Lantern with Motion Sensor

Page 1 / 4

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements.

2. Read and save these instructions.

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF

POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE.

Important to Know

1. Read all instructions carefully before installation and

operation.

2. If you are not familiar with state and local electrical

codes, it is recommended that you consult with a

qualified electrician.

3. Before installation, shut off power at the main fuse or

circuit breaker box. Be aware that simply turning off

the wall switch is not sufficient to prevent an electrical

shock.

4. This fixture requires a 120 VAC, 60 Hz power source.

Maximum wattage light bulb is 60W.

5. Do not attempt to take the lantern apart; there are

no serviceable parts inside.

6. To avoid sensor damage by lightning or electrical

surge, make sure the grounding wire is securely

connected.

7. For general safety and to avoid any possible damage

to the sensor, be sure the power is switched "off"

before replacing the bulb.

Maximum Wattage: 60W

Work Temperature: -4

F ~ 104

Features

2.Use the dim-to-bright illumination option where

1.Energy saving fixture.

you want some minimum illumination through out

the night, such as at your front entrance or garage

door. Use the dark-to-bright illumination option

where you do not need minimum brightness, such

as the backyard or back porch.

3.When in manual override mode, use wall switch

to keep the light on till dawn.

Hardware Package (included)

Green Grounding

Screw

Mounting Screw

Wire Nut

Lock Nut

Ball Nut

Mounting Plate

Headless Screw

Rubber Pad

Headless Screws

Mounting plate

House Grounding Wire

Green Grounding Screw

Fixture Grounding Wire

Wire Nut

Outlet Box

Fixture Wire

Lock Nuts

Back Plate

Ball Nut

Rubber Pad

Max 60W Type A

standard base bulb (Bulb not included)

Socket Ring

Glass Shade

Mounting screw

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND INSTALLATION INSTRUCTIONS WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER BEFORE INSTALLING OR SERVICING THIS FIXTURE. NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. Read and save these instructions. Important to Know 1. Read all instructions carefully before installation and operation. 2.
PAGE 2
Installation Steps 1. Shut off power at the circuit breaker of where the fixture is to be installed. 2. Thread two headless screws through the cross bar, then secure them with four lock nuts (two on each side of the mounting plate). Adjust the length of the headless screws if necessary. Note: Make sure that the headless screws are lined up horizontally, in order to ensure that the fixture will be level. 3. Attach the mounting plate to the outlet box by using two mounting screws. 4.
PAGE 3
5.Manual Override MODE (nighttime operation only; on at dusk,off at dawn) ● In 3, 6 or 0 mode, to shift to manual override mode, turn off the wall switch in 3 seconds and then turn it on again, the light will turn to high-level brightness at dusk, and turn off automatically at dawn. To return to the previous settings, turn off the wall switch in 3 seconds and then turn it on again. (See Fig.1) ● The lights will turn off automatically at dawn.
PAGE 4
Troubleshooting ---If the light does not work at all: 1. Make sure the wall switch and circuit breaker are on. 2. Make sure the wiring connection is correct. 3. Make sure the bulb is not burned out. 4. Cover the sensor with your palm to verify that the ambient light level is not too high. ----In Test Mode, if the light stays on full brightness after 5 seconds: 1. Check whether the motion is detected at all time. ----After performing 3H or 6H mode, or in 0 H mode.