BC ○ TABLET COMPUTER DT13 USER’S GUIDE
Notice Copyright© 2018, MilDef Crete Inc. All rights reserved. No part of this publication may be reproduced and modified without the written permission of MilDef Crete Inc. MilDef Crete Inc. reserves the right to make changes in the products or the product specifications without any prior notice. Customers are advised to contact MilDef Crete Inc. for updated product information. MilDef Crete Inc.
Regulatory Information/Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
FCC (Federal Communications Commission) regulatory compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules.
CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 2004/108/EC ). The equipment was passed, and the equipment test was performed according to the following European standards: EN 300 328 V1.8.
Power Conservation This tablet computer consumes less power compared to conventional consumer computers. The power consumption may be further reduced by properly configuring the Power Management Setup. It is recommended that the power saving features be enabled even when not running on battery power. Power Management features can conserve power without degrading system performance.
Battery Preservation Precaution Only use batteries designed for this computer. Using incompatible battery types may cause explosion, leakage or damage to the computer. Do not store your battery in high moisture condition, low temperature or high temperature. Proper storage temperature is 5~20°C and capacity is suggested to remain 50%. Do not put your computer and battery near any heat source(oven, stove…). Do not remove the battery from the computer while the computer is powered on.
short time. Battery protection If a battery keeps being charged with high voltage, the cell would age faster. To prevent this, once the battery is charged to 100%, the system will not keep charging it and the capacity might decrease and remain between 90~100%. Notice: For safety, recharging will stop if the internal temperature of the battery is out of range(<0°C; >50°C).
Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials in accordance with local regulations at the end of the product's service life. Notice: The equipment may contain insignificant amount of hazardous substances for health and environment below control level.
TABLE OF CONTENTS CHAPTER 1 - GETTING STARTED .............................................................. 1 UNPACKING .................................................................................................................. 1 APPEARANCE OVERVIEW ............................................................................................... 2 CHAPTER2 - OPERATING INFORMATION ................................................. 6 START USING YOUR TABLET COMPUTER .....................................
TOUCH SCREEN .......................................................................................................... 34 STORAGE ................................................................................................................... 34 AUDIO ........................................................................................................................ 35 I/O PORTS ..................................................................................................................
Getting Started Chapter 1 - Getting Started Unpacking The following components come with your computer. If anything is missing or damaged, please notify the dealer immediately.
Getting Started Appearance Overview Front 1. Keyboard 2. Buttons 3. LED Indicators 4.
Getting Started Rear 1. 2nd Battery Connector Left 1. Battery Slot 2. USB 3.1 Type C x 1 3. USB 3.1 Type A x 2 4. SD Card Slot x1 5. SIM Card Slot x1 6.
Getting Started Right 1. DC-In x 1 2. GLAN x 1 3. DB15 x 1 Top 1. Night Vision Switch 2. SSD slot 3. GPS SMA Connector 4. GPS Antenna 5.
Getting Started Bottom 1.
Operating Information Chapter2 - Operating Information Start Using Your Tablet Computer Always turn on your tablet computer by using the power button. Press the power button about 2 seconds and the tablet will boot up. This is the standard operating procedure to start using your tablet computer. After turning on the power of your tablet computer, it will start with the Operating System (OS) installed. Boot Up When you turn on the power, your computer will start to load the OS into the system memory.
Operating Information Stop Using Your Tablet Computer Each time when you finish working with your tablet computer, there are several ways to stop your tablet computer from operating. Shut down Directly click “Shut down” from your OS to turn OFF the power of your computer. Before shutting down, please do remember to save unfinished works and close your applications to prevent your SSD from suffering possible data loss or damage. “Shut down” will turn OFF power of your computer.
Operating Information Installing Operating System Your computer is designed to operate with Microsoft Windows 10 / 64-bit Operating System. Please connect your computer with an external USB-interface drive to start the OS installation. Note: A USB hub may be required during installation to connect with an external USB-interface ODD, as the System USB port may not supply enough power. Please connect your USB hub with extra power supply to complete the installation.
Operating Information Input Lock key To prevent from unexpected input by buttons and touch screen, you can press Input Lock key. When Input Lock function is on, the input from devices including buttons and touch screen will be locked. To cancel the input lock function, just press the Input Lock key again and the indicator will be turned off. 1. Press the Input Lock key. 2. Input Lock Indicator will light on (Green light). 3. Press the Input Lock key again to cancel the function.
Operating Information Setting Function for Buttons A1~A3 Hotkey Manager is an app which could be used to quickly set up and change between multiple functions for A1, A2 and A3. Please follow these procedure to use it. 1. Operate the Hotkey Manager then a menu will show up. 2. Scroll down to select function for each key. 3. Click and the setting will be saved automatically.
ERROR: ioerror OFFENDING COMMAND: image STACK:
