Product Info

ManualsBrandsMikrotikls ManualsElectronicsLtAP

Table Of Contents

RBLtAP-2HnD

The RBLtAP-2HnD is a wireless access point with two WiFi data for using with your own modem.

Powering

• Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-30 V DC.

• Automative port accepts 12-30 V powering.

• Ethernet port accepts passive and 802.3af/at Power over Ethernet 12-30 V DC (compensate for loss on

cable, so more than 12 V recommended).

The power consumption under maximum load can reach 12 W.

Mounting

It is possible to attach the device to a wall, using the provided screw holes on the sides of the unit. The device

should be mounted in a way that the cable openings are pointing downward. The ports are protected with a small

door, that is held in place with one screw. The door has cut-out places for all available ports, but please only break

out the openings that you will use. The device can be used both indoors and outdoors.

Setup

1. Set your computer IP configuration to automatic (DHCP).

2. From your PC or smartphone, connect to the wireless network name which starts with “MikroTik”.

3. Once connected to the wireless network, open http://192.168.88.1 in your web browser to start

configuration, since there is no password by default, you will be logged in automatically. Set up your

password in the screen that loads. Please also specify your country, to make sure local regulations are

observed.

Configuration

RouterOS includes many configuration options in addition to what is described in this document. We suggest to

start here to get yourself accustomed to the possibilities: http://mt.lv/help. In case IP connection is not available, the

Winbox tool (http://mt.lv/winbox) can be used to connect to the MAC address of the device from the LAN side (all

access is blocked from the internet port by default).

For recovery purposes, it is possible boot the device from network, see section Buttons and jumpers.

See mikrotik.com for more information. Document #45462, modified on 07/03/18

Summary of content (4 pages)

PAGE 1
RBLtAP-2HnD The RBLtAP-2HnD is a wireless access point with two WiFi data for using with your own modem. Powering • • • Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-30 V DC. Automative port accepts 12-30 V powering. Ethernet port accepts passive and 802.3af/at Power over Ethernet 12-30 V DC (compensate for loss on cable, so more than 12 V recommended). The power consumption under maximum load can reach 12 W.
PAGE 2
Extension slots and ports  Built-in WiFi wireless access point module, AP/station/bridge/p2p modes are supported. Onboard PIF antennas built in.  Built-in GPS module with a built in antenna. One uFL connector provided for an external antenna (available separately). To enable, set the port to serial0 (this disables the DB9 port on the unit). One 10/100/1000 ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X).
PAGE 3
Federal Communication Commission Interference Statement FCC ID: TV7LTAP2HND This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
CE Declaration of Conformity Full Declaration of Conformity (DoC) may be obtained by visiting our product page on https://mikrotik.com/products Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039. EN Hereby, Mikrotīkls SIA declares that this RouterBOARD is in compliance with the essential requirements and other relevant provisions of directive 2014/53/EC.