User Manual

ManualsBrandsMikroTik ManualsComputers & AccessorieswAP LR9 kit

Table Of Contents

wAP LR9 kit

wAP LR9 kit

The wAP is a small weatherproof device with an integrated LR9 card for UDP packet forwarding to the chosen server.

Quickstart

Make sure your ISP is allowing hardware change and will issue an automatic IP address.

Open the bottom lid.

Connect an external antenna to the SMA connector.

Connect the device to the power source.

Connect with your device to the MikroTik wireless network

The configuration has to be done through the wireless network using a web browser or mobile app. Alternatively, you can use the WinBox

configuration tool . By default, Ethernet port access is blocked by a firewall.https://mt.lv/winbox

Once connected to the wireless network, open in your web browser to start the configuration.https://192.168.88.1 

user name: a and there is no password by default.

dmin



When using a mobile application choose Quick setup and it will guide you through all necessary configuration in six easy steps.

Find your LR Gateway ID on the label within the product and register it in your Network Server.

To make the device connect to the LR Network Server.

Click the "Check for updates" button and update your RouterOS software to the latest version, the device needs to have an active Internet

connection.

After update set your country, to apply country regulation settings.

Set your WiFi password.

Set the router password.

Expansion slots and ports

10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for

connecting to other network devices.

External SMA antenna connector already connected to the LR card.

LED indicating a power state of the device.

LED Indicating the activity of Wireless network.

Automotive connector. Pinout: A - reserved for future use (orange), B - reserved for future use (blue), C - ground (black), D – power in (red).

MiniPCIe slot with integrated LR9 card.

Integrated Wireless module operating at 2.4 GHz, 802.11b/g/n protocol.

SIM slot.

Powering

The device accepts power in the following ways:

Summary of content (12 pages)

PAGE 1
wAP LR9 kit wAP LR9 kit The wAP is a small weatherproof device with an integrated LR9 card for UDP packet forwarding to the chosen server. Quickstart Make sure your ISP is allowing hardware change and will issue an automatic IP address. Open the bottom lid. Connect an external antenna to the SMA connector. Connect the device to the power source. Connect with your device to the MikroTik wireless network The configuration has to be done through the wireless network using a web browser or mobile app.
PAGE 2
Ethernet port accepts passive PoE 9-30 V DC . Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 9-30 V DC. Automotive connector 9-30 V DC. The power consumption under maximum load can reach 7 W. Connecting to a PoE Adapter: 1. Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter. 2. Connect an Ethernet cable from your local network (LAN) to the PoE adapter. 3.
PAGE 3
6. Close bottom latch and secure with a screw. It's recommended to secure Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm. Mounting unit on the wall: 1. Use included a template to mark spots for drilling holes. And if needed for Ethernet cable. Align accordingly, it will depend on how the device will be mounted finally. 2. Insert dowels if needed, depends on wall structure and material. 3. Place included a steel bracket on the wall. 4.
PAGE 4
Mounting on the ceiling: A Special bracket is included in the package to mount on the drop ceiling. As it consists of two parts, to be attached on both sides of the ceiling tile. 1. Use the template to mark spots for holes. 2. Place both mounting brackets on the spot. 3. Secure them together using screws. Continue assembling in the same manner if mounting on the wall. 1. 2. 3. 4. Extend your Ethernet cable through the opening and connect to the Ethernet port. Mount the device on the steel bracket.
PAGE 5
Use Torx T20 screwdriver to unscrew it, but do not remove the screw completely. Pull the cover in the opposite direction from the device to remove it. Reassemble. Configuration To set the configuration for LR please connect to the device and log in with your web browser or use a mobile application. Two easy steps to follow: First step: 1. Once logged in, Quick Set will be selected, please switch to WebFig on the right side of the screen.
PAGE 6
Name: (Server name) Address: (Server address) Up port: (Usually it's 1700) Down port: (Usually it's 1700) 1. Click OK to save. Second step: 1. 2. 3. 4. 5. 6. Select the Device tab on the previous window. Double-click or tap on the line to configure. Choose the previously entered network on the drop-down menu. Click on the button Enable to enable the gateway. Click OK to save. The configuration is done.
PAGE 7
Use PH2 screwdriver to remove the screw. Disassemble upper case from the bottom by sliding them to opposite sides. Locate internal antenna cable and replace it with the SMA cable connector on the LR card. Reassembly. Buttons and jumpers The reset button has three functions: Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds). Keep holding for 5 more seconds, LED turns solid, release now to turn on CAP mode.
PAGE 8
Package includes the following accessories that come with the device: EU/US Switching Power Supply 24 V , 0.8 A, 19.2 W, 85.3 %, VI, cable:150 cm Hor CMC. WAP desk bracket. WAP outdoor case bracket AL, white. POE Injector cable. Cable (H4130-04PDB000R 3 mm 2x2P Housing) to (StripJacket 5 cm+WireEnd Strip/Tin 1 cm) 24 AWG. Hose Clamp, 35-70 mm, W4. K-52 fastening set. WAP-drill-template, paper brochure. Operating system support The device supports RouterOS software version 6.44.5.
PAGE 9
IC: 7442A-WAPR2ND This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 10
FR Le soussigné, Mikrotīkls SIA , déclare que l'équipement radioélectrique du type RouterBOARD est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: https://mikrotik.com/products HR Mikrotīkls SIA ovime izjavljuje da je radijska oprema tipa RouterBOARD u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: https://mikrotik.
PAGE 11
SL Mikrotīkls SIA potrjuje, da je tip radijske opreme RouterBOARD skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://mikrotik.com/products SV Härmed försäkrar Mikrotīkls SIA att denna typ av radioutrustning RouterBOARD överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: https://mikrotik.
PAGE 12
* It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed! Note. Information contained here is subject to change. Please visit the product page on www.mikrotik.com for the most up to date version of this document. BG. Инструкция: Свържете адаптера на захранване, за да включите устройството.