User Manual

ManualsBrandsMikroTik ManualsAccessoriesMTP250-26V94-OD

Table Of Contents

MTP250 series

MTP250 series

MTP250-53V47-OD

MTP250-26V94-OD

Safety information

Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for

preventing accidents. The installer should be familiar with network structures, terms, and concepts.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making

sure, that the Installation of the equipment is compliant with local and national electrical codes. Do not attempt to disassemble, repair, or modify

the device.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate

at your own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power adapter from the power outlet.

Contact time to touch PSU will be (> 1 s and < 10 s).

Information

Technical specifications, brochures, and more info about products at https://mikrotik.com/products

If you need help with configuration or installation, please seek a consultant https://mikrotik.com/consultants

Powering

The device accepts power from an AC source:

Input: 100-240V ~ 50/60Hz.

Output:

MTP250-26V94-OD MTP250-53V47-OD

DC output voltage (V) 26 53

DC output current (A) 9.4 4.7

DC output power (W) 244 249

Summary of content (5 pages)

PAGE 1
MTP250 series MTP250-53V47-OD MTP250-26V94-OD Safety information Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. The installer should be familiar with network structures, terms, and concepts. This equipment is to be installed by trained and qualified personnel, as per these installation instructions.
PAGE 2
Installation For installation Use a CU wire of at least 1.2 square millimeters for the DC output. On the input side, 100-240V ~ 50/60Hz connect MTP250 series PSU to RCD. Mounting Use provided steel clamp and guide through holes then secure the device to the mast. Or use provided screws and secure device to the wall, use dowels depending on the wall material. Accessories The package includes: CLAMP1-2_ Hose Clamp SUS304 (Philips type; 9mm; clamping diameter range 25-70mm) with EPE bag.
PAGE 3
WARNING. Warning statements identify conditions or practices that could result in injury or loss of life. Symbols on the Product The following symbols may appear on the product: HIGH VOLTAGE: This symbol indicates high voltage. It calls your attention to items or operations that could be dangerous to you and other people operation this equipment. Read the message and follow the instructions carefully. Double insulated. Do not dispose of electronic equipment as unsorted municipal waste.
PAGE 4
EL Με την παρούσα ο/η Mikrotīkls SIA , δηλώνει ότι ο ραδιοεξοπλισμός MTP250-26V94-OD/53V47-OD πληροί την οδηγία 2014/30/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: https://mikrotik.com/products EN Hereby, Mikrotīkls SIA declares that the radio equment type MTP250-26V94-OD/53V47-OD is in compliance with Directive 2014/30/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.
PAGE 5
NL Hierbij verklaar ik, Mikrotīkls SIA , dat het type radioapparatuur MTP250-26V94-OD/53V47-OD conform is met Richtlijn 2014/30/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres: https://mikrotik.com/products NO Mikrotīkls SIA erklærer herved at utstyret MTP250-26V94-OD/53V47-OD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/30/EU.