Device Manual
VBar Control Device Manual Mikado Model Helicopters GmbH Friedrich-Klausing-Str. 2 · 14469 Potsdam · Germany Telefon +49 331 23749-0 · Telefax +49 331 23749-11 info@mikado-heli.de · www.mikado-heli.de © Mikado Model Helicopters 2014. All rights reserved. v1.
Table of Contents Benefits at a Glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Binding a VBar Control Satellite Receiver . . . . . . . . . . . . 16 Software Highlights: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Battery Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Hardware Highlights:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Tips for using your VBar Control Transmitter . . . . . . . . . .
Benefits at a Glance Software Highlights: ■■ Setup, programming and adjusting of VBar-controlled models accomplished directly via VBar Control radio. ■■ No computer, control panel or smartphone necessary. ■■ Instant access to almost every flight parameter from the transmitter controls, even in flight. ■■ Easy programming for new helicopters via the familiar VBar setup wizard. ■■ New ESC setup wizard for programming all types of speed controllers. ■■ Bank switching with three banks.
Introduction Welcome to VBar Control Thank you for choosing this highly specialized yet versatile product. To safely operate and fly your radio controlled models using the VBar Control, you must read and follow this device manual carefully. For software and model setup, see the quick start guides and manuals provided with this radio, as well as documentation provided with the necessary components, such as motor, electronic speed controller, servos, the helicopter kit itself.
General Safety Precautions Precautions for the Use of the 2.4 GHz Band VBar Control operates in the 2.4 GHz band, which is in common use with e.g. industry, science and medical (ISM) applications. It is widely used for microwave ovens, shortrange wireless communications like WiFi, bluetooth, cordless appliances like headphones, or amateur radio. Excessive use of the 2.4 GHz band (like in urban areas) may degrade the control response and range of VBar Control.
Built-in Rechargeable Lithium Polymer Battery and Battery Charger ■ Take special care with the following to prevent unwanted heat generation, fire and explosion. ☠☠ Danger Use only the supplied wall charger with the appro- priate adapter. Check the voltage in the country you are in, it must not exceed 100-240 V AC. »» Do not misconnect (+) and (–) »» Do not place VBar Control or the charger next to heat or open fire.
Transmitter Controls and Features ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Antenna Gimbals Adjustable sticks Switches 1-6 Rotating knobs 1+2 Easy Dialog System Dial (EDS) with LED ring XXtra Bright Graphic Display Ambient light sensor 3-point neck-strap attachment Speaker Rubber grip lining Rubber grip Antenna lining Carrying handle USB connector with protective rubber cover Charging connector and reset button with protective rubber cover Transmitter battery (installed) Stick tensioners Collective stick brake
Basic Transmitter Operation How to turn the VBar Control on and off ■ Turn on your VBar Control by pressing down the Easy Dialog System Dial (EDS Dial), and at the same time rotate 90° clockwise. ■ Turn off your VBar Control by pressing down the EDS Dial, and at the same time rotate 90° anti-clockwise. Choose OK from the Shutdown menu by rotating the EDS, then click OK. ■ Mind that you cannot turn off your VBar Control as long as a VBar Control Receiver is connected, so always turn off your model first.
Minimum Brightness sets the low threshold for the ambient light sensor. The display will not go darker than the value set here. To save on battery life, use the lowest convenient value. Sound volume i s for the EDS Dial feedback as well as for warnings and Speech Apps. You can calibrate the gimbals by selecting one control function at a time and thereby ‘show’ the VBar Control the limits and the center position by just moving the stick. It will learn and store the values automatically.
Collective Center Fine a llows to set the zero collective position, even though the gimbal has no spring to center itself. Move the stick to the precise mechanical center position according to the zero pitch line on the gimbal’s scale, press Set Zero!. Mandatory switches assigns three switches needed for basic flight operations and the directions according to your liking. Defaults are Motor—upper left, Bank switch (flight modes)—upper right, Buddy Box—lower right.
How to change the Stick Mode and adjust the Stick Tension, how to change the Stick Length ■ Tools needed: 3 mm and 2 mm hex screwdrivers, PH0 x 50 Philips screwdriver, pliers. ■ Turn off your VBar Control transmitter ■ Remove the neck strap. ■ Put the VBar Control transmitter face down on a soft surface. 1Remove the six screws M3x20 mm to take off the bottom case. Then flip the case over so the screws fall out of the bottom case.
2 5 8 q 3 4 6 7 9 0 w 15
How to use VBar Control as a USB Game Controller ■ Select USB mode Simulator from the Transmitter Setup. ■ Connect the USB lead to your computer. ■ There is no driver needed on Windows PCs nor on Macs. The operating system will detect VBar Control automatically as a game controller. ■ In your preferred simulator software, select VControl as a controller and set up/calibrate as needed. ☝☝ Attention: Use the Simulator’s menus to adjust the Simu- lator to the VBar Control transmitter.
VBar Control Satellite Receiver Features ■ Antennae »» Coaxial antenna wire »» Actual antenna wire ■ Connector ■ Connecting cable (for Mikado VBar or Mini VBar only) ■ Control LEDs Connecting cable Actual antenna wire Coaxial antenna wire Control LEDs Antennae Control LEDs ■ The green LED signals that the receiver is bound to and synchronized with VBar Control. ■ The red LED flashes when data are being sent, e.g. telemetry is active.
Updating and Enhancing your VBar Control Transmitter Installing and Using VBar Control Manager ■ PC »» Go to our product web site www.vstabi.info, browse to the downloads section and get a download link for the VBar Control Manager (you will need a MikadoID (= login name to at www.mikado-heli.de) to do so). »» After the actual download, open the installer and follow the instructions on the screen. »» The program will be installed to the \Program Files-Folder on your hard disk.
☝☝ Attention Legal warranty periods may differ depending on Technical Data the laws applicable in the country you live in. Please ask your local dealer/distributor for further details.
15C 15C 2401 0 - 2481 0 2401 0 - 2481 0 0 099 0 096 Output power listed is conducted. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.