Operating instructions Washer-dryer WT 946 i S WPS To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed or used for the first time. G M.-Nr.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal of your old appliance or machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description of the appliance . . . . . . . . . . . . . . . . .
Contents Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Washing with several components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Fabric conditioners / starch formulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Fabric conditioners, texturisers and starch . . . . .
Contents A fault indicator lamp comes on but the wash programme continues as normal. 46 General problems or an unsatisfactory wash or drying result. . . . . . . . . . . . . . . . 47 Opening the drum door in the event of a blocked drain outlet and/or power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Draining the machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Opening the drum door . . .
Caring for the environment Disposal of the packing material Disposal of your old appliance or machine The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Electrical and electronic appliances / machines often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment.
Warning and Safety instructions Read the operating instructions before using this machine for the first time. They contain important information about the safety, installation, use and maintenance of the machine. This way you will avoid the risk of accidents and damage to the machine. Keep these operating instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner of the machine.
Warning and Safety instructions The Miele "Waterproof system" protects from water damage provided the following conditions have been met: – the machine is correctly plumbed in and connected to the electricity supply. – if a fault has been identified, the machine must be examined by a competent person before further use, and repaired if necessary. Faulty components must only be exchanged for Miele original spare parts. Only when these parts are fitted can the safety standards of the machine be guaranteed.
Warning and Safety instructions If the correct amount of detergent is dispensed, the machine should not need to be descaled. If, however, you do wish to descale the machine only use proprietary non-corrosive descaling agents and strictly observe the instructions on the packaging. If in doubt, contact the Miele Customer Service Dept. or your Miele Dealer. Never use solvent based cleaning agents in this machine, as this may result in damage to component parts and create toxic fumes.
Description of the appliance This washer-dryer can be used: Delay start – to wash separately with a max. load (depending on programme) of 5 kg; Delay start allows you to delay the start of a programme from 1 hour up to a maximum of 9 hours. – to dry separately with a max. load (depending on programme) of 2.5 kg; or – to wash and dry in a continuous sequence with a max. load (depending on programme) of 2.
Description of the appliance Control panel a Delay start button and display This is used to delay the start of a programme. The delay time will appear in the display. f "Spin" button for changing a spin speed or selecting – Rinse hold or – Without final spin. b "START" button Press the Start button to start a programme. The Start indicator lamp will flash as soon as a programme can be started. g Additional option buttons for selecting additional functions.
Description of the appliance Important control panel features Programme selector The programme selector is used to set the – basic wash programmes and temperatures and – the drying programmes and temperatures. Additional option buttons Additional options can be added to the basic programme. Pressing the relevant button selects or de-selects the particular option. An additional option is selected if its indicator lamp is on.
Washing and drying environmentally – Ideally load the maximum amount specified for the programme you are using. This way energy and water consumption will be kept to a minimum. – Use the QUICK WASH programme for small loads. – Use the Short wash option for lightly soiled laundry. – A main wash (programme without pre-wash) is sufficient for cleaning normally soiled laundry. – Use the Soak option for heavily soiled laundry.
Before using for the first time Before using the machine for the first time ensure that it is correctly installed and connected. See the relevant section under "Installation". There is a yellow lever behind the detergent drawer facia panel. Flushing out the drum ^ Turn on the stopcock. ^ Turn both programme selectors to the Finish position. ^ Switch the machine on with the I-ON / 0-OFF button. Do not load any laundry. ^ Add max.
WASHING Programme overview COTTONS e Fabric type Additional options Notes Cottons and linen fabrics, e.g. bed linen, table linen, towelling, jeans, underwear, T-shirts, nappies. Soak, Pre-wash, Water plus, Short. – Only use the COTTONS 95°C programme for heavily soiled and incontinent laundry. – For heavily soiled laundry select the Soak or Pre-wash additional option. – For lightly soiled laundry select the Short option.
WASHING Programme overview DELICATES f Fabric type Additional options Notes Acrylics, acetate and triacetate, 100% cotton easy care shirts and blouses. Curtains, specified machine-washable by the manufacturer. Detergent Soak, Pre-wash, Short – Laundry remains relatively crease-free for easier ironing. – Dust in curtains usually makes using a programme with Pre-wash advisable. – For curtains made from delicate fabrics reduce the spin speed or select Without final spin. Detergent for delicates Max.
WASHING Programme overview Starch Fabric type Table cloths, napkins, overalls, aprons. Notes – The laundry should be washed but not treated with fabric conditioner. Max. load 5 kg Drain / Spin Notes Max. load Separate rinse Fabric type – Drain only: Select Without final spin. 5 kg Notes Articles which have been washed by hand and only need to be rinsed and spun in the machine. – Do not use for woollens. Max.
How to wash correctly Care symbols - washing Care symbols Fabric types Description of process Programme: (select the appropriate temperature according to the temperature on the care label symbol) e no bar Cottons Normal Cottons, Minimum iron, Quick wash (maximum) machine action and normal spinning f Synthetics Reduced Delicates single bar (medium) machine action and reduced spinning g broken bar Woollens Much reduced Hand Wash Woollens programmes.
How to wash correctly Important - other care symbols / Hand wash h Do not wash apf Dry clean D Do not dry clean y Suitable for chlorine bleaching z Do not use chlorine bleach Tumble dry q At normal temperature r At low temperature s Do not tumble dry Ironing I Hot iron H Medium hot iron G Cool iron J Do not iron 18
How to wash correctly Separate washing Make sure that the DRYING programme selector is at theFinish position. Otherwise the drying programme set will follow on from the washing programme. Before washing A Sort the laundry ,Do not use solvent-based cleaning agents in this machine. ^ Sort the laundry by colour and by care label symbol. Most garments have a textile care label in the collar or side seam. See the "Programme overview chart" for information on which programmes to use for different fabric types.
How to wash correctly B Switch the machine on Select a programme ^ Press in the I-ON/0-OFF button. G Select the wash programme. C Open the drum door ^ Press the Door button and open the drum door. D Load the drum ^ Unfold the laundry and load loosely in the drum. To achieve best results make up mixed loads consisting of both large and small items. Do not exceed the maximum load for the programme selected. This uses the energy and water to the best advantage.
How to wash correctly Selecting additional options for the wash programme I Select additional option(s) For programmes without a pre-wash: – Add the total amount to compartment j or directly into the drum on top of the laundry. For programmes with a pre-wash: – Add 1/4 of the detergent for the soak and pre-wash into compartment i, and 3/4 into compartment j for the main wash. Pre-wash For heavily soiled and stained items. Water plus ^ Press the required addtional option button(s).
How to wash correctly J Adding detergent It is important to dispense the correct amount, because... . . . . . too little detergent results in: – Laundry not being cleaned properly and with time it may become grey and hard to the touch. – Greasy particles clinging to the laundry. – Limescale deposits on the heater elements. . . . too much detergent results in: – Excessive foam, which causes a low level of agitation and poor wash, rinse and spin results.
How to wash correctly Delay start K Select Delay start Memory function If an additional option(s) is selected for a programme, and / or the spin speed is altered, the machine stores these changes in memory at the start of a programme. When that particular programme is chosen again, the display will show the additional option(s) and / or spin speed which have been stored for that programme in the memory.
How to wash correctly Adding and removing laundry The door cannot be opened, if: Laundry can be added or removed after the start of one of the following programmes: – the suds temperature is above 70°C (except when the programmable function "Opening the door at high temperatures" has been activated. Warning: The water in the machine will be very hot and could cause burning or scalding. – COTTONS – MINIMUM IRON – QUICK WASH 40°C ^ Press the Door button in and hold it until the door springs open.
How to wash correctly Programme cycle This washing machine has fully electronic controls with automatic load recognition. This machine takes in the right amount of water required for the programme, depending on the amount of laundry and its absorbancy rate. This means that programme cycles and durations can vary. The programme sequences outlined below are based on the basic programme with a full load. Additional options which can be selected, have not been taken into account.
How to wash correctly QUICK WASH Special features in the programme sequences: Main wash Anti-crease: Water level: low Wash rhythm: normal At the end of every programme, with the exception of the WOOLLENS programme, the anti-crease action switches on for a maximum of 30 minutes.
Adding detergent Detergent All modern detergents produced for automatic washing machines are suitable, including liquid, compact (concentrated), tablets and special application detergents. Woollens and knitwear containing wool mixtures and hand-washable garments should be washed using a detergent specifically designed for washing woollens. Instructions for use and recommended amounts for a full load are given on the detergent packaging.
Fabric conditioners / starch formulations Fabric conditioners, texturisers The conditioner or liquid starch is automatically dispensed in the last and starch Fabric conditioners make garments soft and fluffy to handle and help prevent static cling when tumble drying. Texturisers are synthetic starch formulations, which stiffen items of laundry, e.g. shirts, tablecloths and bed linen. rinse. At the end of the programme a small amount of water remains in compartment p.
DRYING Tips on drying ^ Before drying check the drying symbol on the wash care label. q Dry at normal temperature r Dry at low temperature (select the Drying/low temp additional option) s Do not tumble dry If there is no symbol, dry at your own risk applying the following principles: – Cottons and minimum iron items should be dried using the appropriate programme. – Delicate fabrics, e.g. acrylics, should be dried at a low temperature (select the Drying/low temp additional option).
DRYING Programme overview COTTONS Extra dry Fabric type Multi-layered fabrics, which are thoroughly dried in the Normal programme. Additional options Thermospin max. 1500 rpm, Drying / Low temp. Note – Do not dry jerseywear in the Extra dry programme (tendency to shrink) Max. load 2.5 kg Normal Fabric type Single and multi-layered fabrics, e.g. mixed load of cotton fabrics (e.g. towelling, jerseywear). Additional options Thermospin max. 1500 rpm, Drying / Low temp. Max. load 2.
DRYING Programme overview MINIMUM IRON Normal plus Fabric type Minimum iron items which are made of synthetic or blended fabrics (e.g. pullovers, dresses, trousers) which are not dried adequately in the Normal programme. Additional options Note Max. load Normal Fabric type Additional options Max. load Hand iron Fabric type Additional options Max. load Thermospin max. 900 rpm, Drying / Low temp. – Spin fabrics for approx. 30 seconds before drying. 1 kg Minimum iron shirts, table cloths etc.
DRYING Separate drying The separate drying programme must be used if the load in the wash programme is greater than the maximum load permitted for drying, or if you only want to dry part of the load that was washed. Make sure that the WASHING programme selector is at the Finish position. Otherwise the washing programme will begin before the drying programme. Before drying D Load the drum ^ Unfold the laundry and load loosely in the drum. Maximum load: Cottons . . . . . . . . . . . . . . . . . . . . 2.
DRYING Programme selection G Select a drying programme The programmes are described in the "Drying programme charts". ^ Turn the programme selector to the required drying programme. ^ For minimum iron fabrics which are being dried in the TIMED DRYING programme, you should always select the Drying/ Low temp. additional option. The sensor drying programmes for COTTONS and MINIMUM IRON include a thermospin process.
DRYING Delay start Exception: Delay start I Select Delay start J Start the programme The START indicator lamp will flash as soon as a programme can be started. ^ Press the START button. After the programme has started the START indicator lamp will light up constantly. ^ Press the Delay start button repeatedly until the required delay start period shows up in the display (from i to 9 hours). Press the"START" button. The chosen time will start to count down hour by hour.
WASHING AND DRYING Washing and drying in a continuous sequence Where the amount of laundry to be washed and dried in one programme does not exceed the maximum weight permitted for the drying programme, washing and drying in one continuous sequence is recommended. It is essential to read both sections "Separate washing" and "Separate drying" first. G Add detergent Use approximately 1/3 less detergent than is recommended by the manufacturer on the packaging. H Select the programme.
After each washing or drying programme At the end of a programme ^ A buzzer will sound (see "Programmable functions") and the Anti crease / Finish light will come on. Press the Door button and open the drum door wide. ,Take care, the metal cap is hot after drying. Do not touch the metal cap located on the inside of the door glass. Danger of burning! ^ Remove the laundry. ^ Check the folds in the door seal for any small articles, e.g. buttons. Remove any fluff from drying from around the door seal.
After each washing or drying programme After drying "Rinse out fluff" programme The fluff which occurs during drying can collect in the drum and also in the suds container. It is best to rinse out this fluff before the machine is used again, so that it cannot be deposited on the next load of laundry. The Rinse out fluff programme must not be used for rinsing items of laundry. Make sure that there are no items of laundry in the drum before starting this programme. ^ Switch the machine on.
Changing a programme sequence Programme sequences can be changed after the START button has been pressed. It is also possible to select a follow-on drying programme any time up to the end of a washing programme. To cancel a programme ^ Turn both programme selectors to the Finish position. The programme sequence indicators will flash one after the other in the programme sequence display. The programme has been successfully cancelled when only the On indicator lamp is on.
Safety lock Safety lock Electronic programme locking (the Locked indicator lamp is on) prevents the door from being opened or the programme cancelled during a programme. – The Anti-crease/Finish lamp flashes to show that an attempt has been made to alter a programme. This has no effect on the programme sequence. To de-activate the safety lock ^ Press the START button until the Locked indicator lamp goes out.
Cleaning and care ,Disconnect the machine from the Cleaning the detergent dispenser electricity supply by switching off at the wall socket and withdrawing the plug before any cleaning and maintenance work. Cleaning the machine ^ Clean the casing with a mild non-abrasive cleaning agent or with soap and water. Wipe dry with a soft cloth. ^ Clean the drum with a suitable proprietary cleaner for stainless steel.
Cleaning and care ^ Clean the siphon tube. 1. Remove the siphon from compartment p and rinse under warm running water. The channel in compartment p should also be cleaned. 2. Replace the siphon securely. Over time, detergent residue can build up in the water jets in the top of the detergent drawer housing. Before replacing the detergent drawer, use a bottle brush or similar to clean them out. Clean the porthole glass. ^ From time to time you should also clean ...
Cleaning and care Cleaning the filter in the water inlet The machine has a filter to protect the water inlet valve. ^ First turn off the stopcock. ^ Unscrew the threaded union connecting the free end of the inlet hose to the stopcock. The filter in the open end of the inlet hose should be checked and cleaned approx. every 6 months. It should also be checked after an interruption to the external water supply. ^ Remove the rubber seal 1 from the recess.
Problem solving guide What to do if ... ? With the aid of the following guide, minor problems can be easily corrected without calling in a Miele service technician, saving you both time and money. The following charts are designed to help you establish the cause of a fault or problem, and rectify it. Please note the following: ,Repair work to electrical appliances should only be carried out by a suitably qualified person in accordance with local and national safety regulations.
Problem solving guide The programme does not start. Problem The On indicator lamp does not light up in the programme sequence display or the START button indicator lamp does not flash. If one of the following indicator lamps is flashing - Soak/Pre-wash - Washing - Rinses The "Locked" indicator lamp is on. 44 Possible cause Remedy There is no power to the machine. Check whether – the door is properly closed. – the mains plug is plugged in. – the mains fuse has blown. There is a fault.
Problem solving guide The wash programme stops and a fault indicator light comes on. Problem Possible cause Remedy The Water inlet/drain indicator lamp is flashing and the load in the machine has not been washed. The water inlet system is blocked. – Turn the programme selectors to Finish. – Open the stopcock. – Select and start the programme again. The Water inlet/drain indicator lamp is flashing. There is a blockage in the water outlet. – Clean the fluff filter and the drain pump.
Problem solving guide A fault indicator lamp comes on but the wash programme continues as normal. Problem The Water inlet/drain indicator lamp flashes during a programme, but the wash programme has run normally. Possible cause Remedy There is a blockage in Check whether: the water inlet. – the stopcock is opened wide enough. – the inlet hose is kinked. The water pressure is – In this case, call the Miele too low. Service Dept. The filter in the water inlet hose is dirty.
Problem solving guide General problems or an unsatisfactory wash or drying result. Problem The door cannot be opened. Possible cause Remedy The machine is not connected to the electricity supply. Insert the plug in the socket. Power cut. Open the door as described at the end of this section. The door was not correctly closed. Press hard against the left hand side of the door and press the Door button. There is still water in the drum. – Turn the WASHING programme selector to Drain.
Problem solving guide Problem Possible cause The door cannot be For safety reasons the opened during or after door cannot be drying. opened when the internal temperature is above 70°C. Remedy Option 1 Wait until the temperature has dropped below 70°C and then open the door. Option 2 Select the cooling down phase*: – Turn the DRYING programme selector to the Finish position.
Problem solving guide Problem The laundry is still damp after a drying cycle. Possible cause The load weighed less than 1 kg. The moisture sensing system cannot operate with too small a load. Remedy In future dry small loads in a TIMED DRYING programme. When washing and – Turn the WASHING and drying in one continuous DRYING programme sequence: selectors to the Finish during the spin the laundry position. formed a ring in the drum – Open the door and because the laundry was loosen the laundry.
Problem solving guide Problem The laundry is not spun satisfactorily. Possible cause The spin speed selected was too low. The machine was not able to distribute the laundry load evenly. Laundry was spun at a reduced spin speed to protect the machine. The fluff filter is clogged. The machine is not steady during a spin cycle. In spite of adequate water pressure, the water flows into the machine too slowly. Large amounts of detergent residue remain in the detergent dispenser drawer.
Problem solving guide Problem Possible cause There is an excessive Too much detergent build-up of foam. was used. Remedy – Follow the manufacturer’s instructions on dosage given on the packaging. – Take the water hardness level into account. – Use less detergent for lightly soiled or small loads. White residues which The detergent – Try and brush out the residues after drying using contained compounds look like powder a soft brush.
Problem solving guide Problem Liquid detergent does not give the required result. Possible cause Remedy Liquid detergents usually – Use a general purpose contain no bleaching detergent containing a agents. They do not bleaching agent. remove fruit, coffee and – Pour stain removers into tea stains. compartment j and liquid detergent into a dispensing ball (Remember to remove the dispensing ball before drying!). – Never put stain removers and liquid detergent together in the dispenser drawer.
Problem solving guide Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the machine off. ,Caution: If laundry has been washed at a high temperature, water draining out of the machine will still be hot. Danger of scalding! If the drain outlet is clogged, a large amount of water will be retained in the machine (up to 25 litres). ^ Point the drain hose into a suitable container. ^ Remove the yellow lever from behind the detergent drawer fascia panel.
Problem solving guide Opening the drum door ,Always make sure that the drum is stationary before reaching into the machine to remove laundry. Reaching into a moving drum is extremely dangerous. ^ Use a spoon handle or similar to push the emergency door latch downwards (see illustration). The drum door will open. ^ Push the hose with the stopper refitted back into the plinth again.
Problem solving guide Cleaning the fluff filter and pump The fluff filter access flap is visible when the drum door is open. ^ Open the access flap. ^ Check that the impeller can turn easily. Remove any foreign objects (e.g. buttons, coins, etc.) and fluff. Clean the fluff filter housing. ^ Replace the fluff filter. ,Make sure it is securely tightened. Otherwise there is a risk of water leakage during use. ^ Remove the fluff filter completely. ^ Clean the fluff filter thoroughly.
Problem solving guide After sales service Appliance guarantee In the event of any faults which you cannot remedy yourself, please contact The appliance is guaranteed for a period of 1 year. – Your Miele Dealer or See the guarantee card supplied with the appliance for further details. – The Miele Service Department (see address on back cover). When contacting the Service Department, please quote the model and serial number of your appliance, both of which are shown on the data plate.
Installation and connection Front view a Electrical connection f Adapter strips b The Waterproof system g Door interior plate with fixing points for a front panel c Drain hose with flexible / detachable swivel elbow d Detergent dispenser e Control panel h Four height adjustable screw feet i Access panel to the fluff filter and the drain pump j Access panel to the emergency door release and drainage 57
Installation and connection Installation surface Installation A concrete floor is the most suitable installation surface. It is far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. Lift the machine from its packaging base and move it to its site. Please note the following: ^ Do not lift the machine by the drum door. Please note the following: ,Ensure that the machine feet and ^ The machine must be level and securely positioned.
Installation and connection Removing the transit fitting A Turn the left-hand transit bar 90°. B Turn the right-hand transit bar 90°. C Withdraw the two bars together with the support plate. D Plug the holes with the plastic caps supplied. The machine must not be moved without the transit fitting in place. Store the transit fitting in a safe place for future use. It must be re-fitted if the machine is to be moved again (e.g. when moving house). Re-fitting is carried out by reversing the procedure.
Installation and connection Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation. ^ Loosen counternut 2 with a screwdriver by turning it anti-clockwise, then unscrew foot 1 together with the counternut. ^ Put the machine back on all four feet. ^ Use a spirit level to check the machine is standing level. Incorrect installation may increase electricity and water consumption and may cause the machine to move about.
Installation and connection Building under: This machine is specially designed for installation under a continuous worktop run in a fitted kitchen. It is supplied with a cover plate which must be used in place of the machine’s own lid. ,To ensure electrical safety the cover plate must be fitted and must not be removed! Please note: – The slides supplied should be used to protect the floor from damage when the machine is pushed into position or taken out for servicing.
Installation and connection Matching the facia panel to the height of adjacent drawer fronts The adapter can be height adjusted to match the height of adjacent drawer fronts by: – adjusting the nuts or – removing one or more of the adapter strips. Adapter strip adjustment range: Fitting the front panel The machine front can be fitted with a decor panel to match kitchen units. If fitted in a MIELE kitchen, a front panel can be ordered pre-drilled with the necessary fixing holes.
Installation and connection Drilling template ^ Place the template on the lower edge of the rear of the door panel. There are four short parallel marks in all four corners of the template. ^ Drill fixing holes for the inner door panel to the specified depth. On chipboard fronts: inject silicone sealant (supplied) into the (= Ø10 mm) free holes. ^ Align the template using these marks as your guide.
Installation and connection Aligning the door The door must align so that it is flush with the control panel. If the door is not flush with the control panel it will not shut properly. Example of a flush door: Example of a door which is not flush: To align the door add or remove the spacers located underneath the door latch. Additional spacers are supplied in the accessory pack. Please note: If you use too many spacers the door will not provide a sufficient seal when shut.
Installation and connection Fitting a plinth facing. Fitting the plinth facing: The appliance plinth below the door can be fitted with a plinth facing to match your kitchen. ^ Stick the velcro strip provided to the appliance plinth. The height and return of the appliance plinth cannot be altered. A higher plinth facia can only be fitted if the overall niche height is higher.
Installation and connection The Miele Waterproof system The Miele Waterproof system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose 1) Inlet hose – The inlet hose is fitted with an additional electrical safety valve which works like an automatic stopcock and is housed in the inlet hose connection box. – It is pressure proof to between 70 and 100 bar.
Installation and connection Connection to the water supply Connection to the mains water supply Installation For the Miele Waterproof system to function correctly, it may only be fitted in the positions shown in the illustrations above. The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washer-dryer has been designed to comply with DIN regulations.
Installation and connection The plastic casing of the safety valve contains electrical components. The Waterproof system must only be connected to its own stopcock. It must not be connected to mixer taps or similar and must not be fitted in areas where there is the risk of water or other liquids reaching it. The protective sleeve of the hose must not be damaged or kinked. Do not get wet.
Installation and connection Maintenance and care If you intend to unscrew the Miele Waterproof system hose from the stopcock it is essential to disconnect the machine from the electricity supply first. Only use a Miele Waterproof system hose should you need a replacement. In order to protect the water inlet valves, the dirt filter in the water inlet safety valve connection must not be removed. Extension hose A 4.
Installation and connection Connection to the drainage system Drain hose connection: The machine drains via a drain pump with a delivery head of 1 metre. The drain hose is 1.5 m long. It must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull. Please note the following 1. Direct into a sink. – Hook the hose over the edge and secure.
Installation and connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with national and local safety regulations. The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained.
Consumption data Programmes Full load kg Programme Water Energy duration consumpti consumpt ion on kWh l h min WASHING COTTONS 95°C 5.0 1.70 59 COTTONS 60°C (1) 5.0 0.95 56 1 53 1 56 COTTONS 40°C 5.0 0.50 56 1 56 MINIMUM IRON 40°C 2.0 0.45 57 1 20 DELICATES 30°C 1.0 0.40 75 1 00 WOOLLENS 30°C 1.0 0.15 25 0 38 2.5 1.
Technical data Height 82.0 cm Width 59.5 cm Depth 57.5 cm Weight, empty 102 kg Max. floor load 1600 Newton (approx. 160 kg) Capacity - Washing Capacity - Drying max. 5.0 kg dry laundry max. 2.5 kg Cottons Voltage see data plate Rated load see data plate Fuse rating see data plate Consumption data see "Consumption data" section Minimum water flow pressure 1 bar (100 kPa) Maximum water flow pressure 10 bar (1000 kPa) Maximum drain pump head 1.00 m Maximum drain pump length 5.
Programmable functions for changing standard settings
Programmable functions The programmable functions can be used to tailor programmes to suit your individual requirements. Once activated the programmable functions remain in memory until they are deactivated. High water level This is useful where a higher quality rinse is required. A Press the additional option buttons Soak and Pre-wash at the same time, hold pressed in and . . B . . . switch the machine on with the I-ON / 0-OFF button. C Then release these buttons.
Programmable functions Additional rinse for the COTTONS programme Suitable for areas with soft water (hardness range I). A Press the additional option buttons Soak and Pre-wash at the same time, hold pressed in and . . B . . . switch the machine on with the I-ON / 0-OFF button. If a particularly good rinsing effect is required in an area with soft water, then the high water level can be activated in addition to the additional rinse. C Then release these buttons.
Programmable functions Buzzer An audible tone will sound at the end of a washing / drying programme. The machine is delivered with this programmable function activated. A Press the additional option buttons Soak and Pre-wash at the same time, hold pressed in and . . B . . . switch the machine on with the I-ON / 0-OFF button. C Then release these buttons. Follow steps A to G to programme and store in memory. – The Soak/Pre-wash and Washing sequence indicator lamps will flash.
Programmable functions Opening the door at high temperatures It is possible to open the door during a washing or drying programme, even if the temperature is above 70°C. ,Warning: The water in the machine will be very hot and could cause burning or scalding. A Press the additional option buttons Soak and Pre-wash at the same time, hold pressed in and . . B . . . switch the machine on with the I-ON / 0-OFF button. C Then release these buttons.
Programmable functions Final residual moisture after drying The machine is set to give the best drying results. You do, however, have the option of shortening or lengthening the drying time if you prefer. Shortening the drying time: by: 1 minute 2 minutes 3 minutes 4 minutes the display will show: I 2 3 4 Lengthening the drying time: by: 1 minute 2 minutes 3 minutes 4 minutes the display will show: 5 6 7 8 Factory setting: 0 – the WASHING and DRYING programme selectors are at the Finish position.
Alteration rights reserved / 3404 / WT 946 i S M.-Nr. 05 876 100 / 03 en - GB This paper consists of cellulose which has been bleached without the use of chlorine.