Operating and Installation instructions Freezer with Ice/Water Dispenser F 1471 Vi To prevent accidents and machine damage read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control panel for freezer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Control panel for Ice/Water Dispenser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Before use . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Exchanging the water filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Filter Performance Data Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 After sales service . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. Electrical safety ~ Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent the possibility of tipping forward. Keep the door closed until the appliance is completely installed and secured per installation instructions. ~ Before installing the appliance, check for externally visible damage. Do not operate a damaged appliance. ~ This appliance must be installed and connected in compliance with the installation instructions.
IMPORTANT SAFETY INSTRUCTIONS Use ~ Persons who lack physical, sensory or mental abilities, or experience with the machine should not use it without supervision or instruction by a responsible person. ~ To reduce the risk of injury, do not allow children to play in, on or near the appliance, especially in the door hinge area. ~ After your freezer is in operation, do not touch the cold surfaces in the freezer compartment, particularly when hands are damp or wet.
IMPORTANT SAFETY INSTRUCTIONS Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable. ~ Take off the door. ~ Leave the shelves in place so that children may not easily climb inside. ~ Consult with your municipal policy on recycling. ~ Be careful not to damage any part of the pipework while awaiting disposal by: puncturing the refrigerant channels in the evaporator. bending any pipework. scratching the surface coating.
Guide to the freezer a Interior lighting b Door shelf c Ice cube maker d Ice cube container e Interior shelf f Control panel for the Freezer g Main switch to turn the appliance On/Off h Freezer basket i Water filter j Ice / Water Dispenser k Control panel for Ice / Water Dispenser l Dispenser m Drip tray with cover 8
Guide to the freezer Control panel for freezer a Access button "p" activates the control panel d On/Off sensor button for the Ice/Water dispenser b Temperature display X colder; Y warmer Allows you to set the desired temperature in the freezer e Sensor button for the temperature and/or door alarm* c On/Off sensor button for the SuperCool function f Water filter change indicator* * Only visible when the relevant function is activated Control panel for Ice/Water Dispenser a Lighting sensor button d
Before use Before using for the first time Turning the appliance On/Off ^ Clean the inside of the appliance and the accessories with a mild solution of warm water and liquid dish soap. Dry with a soft cloth. ^ Open the appliance door. After installing the appliance, wait at least 30 minutes before switching the appliance on. During transport, fluids in the freezer system may have shifted and will need some time to settle. ^ Turn the appliance On/Off with the main switch.
Settings Using the settings Custom settings When a sensor button has been selected with a finger touch, it will appear yellow. A de-selected button will appear white. In the custom settings mode you can select and change functions. The function possibilities are described in the respective chapters of this manual. Function ^ Touch the access button "p" so it turns yellow. On the control panel you will see additional sensor buttons to operate the appliance.
Settings Turning the button sound On/Off ^ Tap the X button until = appears in the display. If you prefer the buttons to be silent when touched the button sound can be turned off. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the X button, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible.
Settings Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions need to be taken: ^ Shut off the water supply line, (several hours before switching off the appliance) ^ Take all food out of the appliance ^ Turn the appliance off ^ Unplug the appliance ^ Empty the ice cube container ^ Clean the interior ^ Remove and discard the water filter (secure the filter cap) ^ Leave the door open to prevent odors 13
Alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed because of energy loss or an open door. The alarm system is always operational, it does not need to be switched on. Temperature alarm If the temperature becomes too warm, an alarm sounds and the "alarm" indicator turns red and flashes. The temperature display shows the highest temperature reached during the alarm.
Setting the temperature Setting the temperature ^ Touch the access button "p" so it turns yellow. ^ Use the X and Y buttons next to the temperature display to set the temperature warmer or colder. Tap the X and Y sensor buttons to raise/lower the temperature 1°, or hold it down to move through the temperature range more quickly. Temperature range The temperature can be set within the following range: 7°F to -11°F (-14°C to -24°C).
Setting the temperature Temperature unit (Fahrenheit/Celsius) The temperature can be displayed in degrees Fahrenheit (°F) or Celsius (°C). ^ While holding down the X button, press the access button "p" once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). ^ Touch the access button "p" so it turns yellow. ^ Tap the X button until † appears in the display. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" to confirm.
Using the freezer efficiently Freezing food Placing food in the freezer Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food. Food to be frozen can be placed anywhere in the freezer. Never refreeze partially or fully defrosted food. Consume defrosted food as soon as possible, it will lose its nutritional value and spoil if left for too long. Do not refreeze defrosted food unless it has been cooked.
Using the freezer efficiently Defrosting Cooling drinks quickly Frozen food can be defrosted in different ways: To cool drinks quickly, switch on the SuperCool function. See "SuperCool" for more information. – in a microwave oven, – at room temperature, – in the refrigerator (the cold given off by the frozen food helps to keep the other food cold), – in a steam oven. Poultry It is especially important to observe proper hygiene when defrosting poultry. Never save the liquid from defrosted poultry.
Using the freezer efficiently Freezing tips – The following are examples of foods suitable for freezing: Fresh meat, poultry, game, fish, vegetables, herbs, fresh fruit, pastry/dough, leftovers, and a range of pre-cooked meals. – The following examples of foods not suitable for freezing: Lettuce, radishes, sour cream, mayonnaise, eggs in their shells, onions, whole raw apples and pears. – To retain color, taste and vitamin C, vegetables should be trimmed, washed, and blanched.
SuperCool When the SuperCool function is activated, the appliance is cooled as cold as possible (to a factory-preset temperature). SuperCool The SuperCool function is ideal for freezing large quantities of unfrozen food. Ideally the function should be switched on 4 - 6 hours before the food is placed in the freezer. If the max. freezing capacity is used, 24 hours are recommended. This helps food to freeze quickly and retain its nutrients, vitamins, flavor and appearance.
Ice/Water Dispenser For the automatic ice/water dispenser to operate, it must be connected to the household power and water supply. Turning on the Ice/Water Dispenser Once the freezer has cooled to a freezing temperature, the ice cube tray filles with water. Cold air is blown directly over the tray. Use sturdy glass when dispensing water or ice - risk of injury from broken glass! As soon as the cubes are frozen they fall into the ice cube container. Keep fingers clear of the dispenser opening.
Ice/Water Dispenser Dispensing water ^ Place a suitable cup on the drip tray. ^ Turn on the Ice/Water dispenser with a finger touch to the control panel or by passing your hand under the dispenser to activate it via the light sensor. All of the touch controls for the Ice/Water Dispenser should now appear white. If this is not the case, the Safety Lock is activated i.e. "lock" will appear yellow. See "Safety Lock".
Ice/Water Dispenser As soon as the drip tray indicator signals that the drip tray is full, the current operation will automatically stop. Empty out the drip tray using a sponge or dish towel. After the appliance is turned on for the very first time, it can take up to 24 hours for the first ice cubes to drop out of the ice cube maker and collect in the container.
Ice/Water Dispenser Using the Ice/Water Dispenser for the first time Before using the Ice/Water Dispenser for the first time, you must flush then fill appliance water lines with water. ^ Open the freezer door. ^ Touch and hold the "water" button again. This activates the flushing function, which uses approximately 1.6 gallons (6 liters) of water. ^ Touch the "Access" button so it turns yellow.
Ice/Water Dispenser Safety lock The Ice/Water dispenser can be locked to prevent unwanted use. ^ Touch the "lock" button so it turns yellow. Turning off the Ice/Water dispenser The water supply line must be shut off several hours before the appliance or ice maker is switched off. ^ Open the freezer door. The Ice/Water dispenser buttons are now locked. To unlock the buttons: ^ Touch the "lock" button so it turns white. ^ Touch the sensor button for the ice maker so that it turns white.
Ice/Water Dispenser Settings Anti-condensation heater The following settings on the Ice/Water dispenser can be adjusted: A heater behind the cover of the Ice/Water dispenser ensures that frost and ice do not build-up. To save energy, you can turn the heater Off. Entering the settings mode This feature is turned off by factory default. ^ Touch and hold the "lock" button (appears white). ^ At the same time tap the "light" button. ^ Hold the "lock" button for approx.
Ice/Water Dispenser Anti-clumping Button sound The anti-clumping feature ensures that crushed ice or ice cubes do not freeze together. A noise will be heard periodically to indicate that the feature is working. If the sound disturbs you, the feature can be turned off. If you prefer the buttons to be silent when touched, the button sound can be turned off. This feature is turned on by factory default. Note: Disabling the anti-clumping feature can result in the formation of ice clumps in the dispenser.
Automatic defrost The freezer defrosts automatically. The moisture generated in the appliance collects in the evaporator. It is automatically defrosted and dissipated by the condenser periodically. This automatic defrosting system enables the freezer to remain permanently ice-free, while ensuring that the food stored in the freezer stays frozen.
Adjusting the interior fittings Moving the shelves Door shelf The shelves can be adjusted according to the height of the food. For easier loading, unloading and cleaning the door shelf can be shifted or completely removed. ^ Using both hands, grasp the shelf from underneath and lift slightly so that the rear of the shelf is slightly above the mountings. ^ Pull the shelf forward. ^ Move the shelf to the desired height, then insert the (rear) hooks into place. ^ Make sure the shelf is level.
Adjusting the interior fittings Freezer baskets Replacing the freezer basket For easier loading, unloading, and cleaning, the freezer baskets can be shifted or completely removed. ^ Fully extend the telescopic tracks. ^ Pull the basket forward until resistance is felt. On the hinged-side of the door is a safety lock, which must be turned to a horizontal position before the drawer can be removed. ^ Using a suitable object, turn the safety lock to a horizontal position a.
Cleaning and care Before cleaning To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents. Non-abrasive cleaning agents are also unsuitable, as they can cause matte areas to appear.
Cleaning and care Aluminum frames Ice cube container The frames of the door bins and shelves are made of aluminum. ^ Pull out the ice cube container. ^ Clean with a mild solution of warm water and liquid dish soap. Aluminum is susceptible to scratches and nicks, treat with care. The aluminum frames may become discolored or otherwise altered if soiling is not cleaned away promptly.
Cleaning and care Ventilation slits After cleaning ^ Check the ventilation slits in the base panel regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. ^ Return all shelves and accessories. Door seals Do not use any oils or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Plug in the appliance and turn it on with the main switch. ^ Switch on the SuperCool function. The freezer section will cool down quickly.
Cleaning and care Changing the light bulb The lighting automatically switches off after the door has been open for approx. 10 minutes. This is not a fault. Never touch a halogen bulb with bare fingers. When inserting a glass halogen bulb always hold with a soft cloth. If the light does not come on when the door is opened briefly, the light bulb should be changed. ^ Use the main switch to turn the appliance off.
Cleaning and care Side lighting Ice/Water Dispenser lighting Do not remove the light cover for the dispenser lighting. Should the lighting covers be damaged or need to be removed due to damage, do not look directly or with an optical instrument at the lighting. ^ Turn the light cover counterclockwise and pull out. The lighting automatically switches off if the dispenser is not used for an extended period of time. This is not a fault.
Water filter The water filter improves the taste and smell of ice cubes by removing chlorine and other substances from the incoming tap water. – Depending on how many ice cubes are produced, the filter will need to be changed approximately every 6 months. It is important to change the water filter regularly.
Water filter Exchanging the water filter ^ Push in and rotate the filter cap on the base panel of your appliance counterclockwise 180°, 1. ^ Pull the used filter cartridge out of the appliance, 2. ^ Remove the cap from the used filter, 3. ^ Take a new filter cartridge out of the packaging and remove the protective cap. ^ Push the cap onto the new filter cartridge, 4. ^ Push the filter cartridge with cap, in a horizontal position, all the way into the opening in the base panel, 5.
Water filter Re-setting the filter indicator ^ While holding down the X button, press the access button "p" once. Keep holding the X button down until the following appears in the display (approx. 5 seconds). The filter indicator still flashes in the display. ^ Tap the X button until an ^ appears in the display. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white.
Water filter ^ Tap the X button until ^ - appears in the display. ^ Touch the access button "p". ^ Tap the X button until ; appears in the display. Deactivating the water filter The ice cube maker in this appliance can be operated without the installed water filter, for example if the household water supply already uses a water filter. If you choose this option, it is important to insert a bypass cartridge. Only then can the performance of the appliance be ensured. ^ Touch the access button "p".
Filter Performance Data Sheet State of California Department of Public Health Water Treatment Device Certificate Number 06 - 1775 Date Issued: March 10, 2006 Date Revised: April 3, 2008 Trademark/Model Designation 9000 077095 Miele 07134220 Replacement Elements 9000 077104 07134220 Manufacturer: Cuno, Incorporated The water treatment device(s) listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminant
Filter Performance Data Sheet Performance Data Sheet For Filter Model 07134220 Using Replacement Cartridge 07134220 This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42 and 53.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. Problems with temperature Issue Possible fault Solution The freezer does not get cold. The machine is not turned Check whether the appliance is on.
Frequently asked questions General problems Issue Possible fault Solution Water is flowing out of Close the shut-off valve immediately. the appliance. Check whether the water Contact Miele Technical pipe in the appliance is Service. defective. Check whether the water pressure is too low. Contact a plumber. Check whether the correct Self-tapping valves and water valve has been 3/16" (4.76 mm) saddle installed. valves reduce the water pressure and can block the pipe. The door will not open.
Frequently asked questions Alarm / Indicator warnings Issue Possible fault Solution The alarm is going off. The appliance door(s) have been open for longer than 5 minutes. Close the door. The alarm is ringing and The door is not closed. the "alarm" indicator is A large amount of fresh flashing. food is being frozen at the same time. There has been a power failure. Once the alarm condition has been corrected, the alarm will turn off and the "alarm" indicator will stop flashing.
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault The ice maker will not The appliance is not switch on. plugged in. The ice maker is not producing any ice. Solution Check that the appliance is connected to the power supply. When the appliance is turned on for the very first time, it can take up to 10 hours for the first ice cubes to drop out of the ice cube maker and collect in the container. The appliance is not turned Check that the appliance is on. switched on.
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault Solution The ice cubes are small. Other domestic appliances that use water are in operation. Avoid using such items as a dishwasher, washing machine or shower at the same time. Check whether the water filter needs changing. See "Water filter" for more information. Check the water pressure. Consult a plumber. The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Frequently asked questions Problems with the ice/water dispenser Issue Possible fault Solution The ice maker is not producing enough ice or the ice cubes are misshapen. Check the water pressure. The water pressure must be between 25 and 120 psi (1.72-8.25 bar). Contact a plumber. Check that the freezer temperature is not too low. See "Selecting the correct temperature". Change the water filter. See "Water filter". The Ice/Water dispenser The appliance is not does not appear to be plugged in.
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service Department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. Keep the door closed until the appliance is completely installed and secured as per the installation instructions. Empty weight of your machine: F 1471 Vi . . . . . . . .
Installation Base Ventilation A fully loaded appliance is very heavy. The load-bearing capacity of your floor must meet the following requirements: The air intake and outlet must not be blocked or covered in any way. They also need to be dusted/cleaned on a regular basis. F 1471 Vi . . . . . . . . . . 505 lbs (229 kg) To ensure that the appliance is installed securely and functions properly, the base must be flat, level and made of a hard, rigid material. If in doubt, contact Miele.
Installation Custom door panels Side-by-side This appliance is compatible with all styles and designs of kitchen cabinetry. This appliance can be installed "side-by-side" with another fridge/freezer using a "Merging Kit". The total weight of the decorative panel(s) must not exceed the following: F 18X1 Vi . . . . . . . . . . . 134 lbs (61 kg) Installation options There are many different installation options. These are limited only by the design of the kitchen.
Installation . . . with partition The minimum thickness of the partition is 5/8" (16 mm). A heating mat must only be installed if the partition wall is less than 6" (160 mm) wide. If there is a partition between the adjacent appliances, then each appliance is to be individually installed within its own niche. For instructions on how to install the heating mat please refer to the instructions included in the "Merging Kit". The "Merging Kit" can be obtained from Miele.
Dimensions Niche dimensions Niche width (A) F 1471 Vi 18" (457 mm) 55
Dimensions 1. Power supply 2. Water connection A F 1471 Vi 9" (229 mm) Door dimensions (open min.
Dimensions 57
Installing the appliance Before you begin Read these instructions completely and carefully. Have the appliance installed by a qualified technician, according to the enclosed installation instructions. To reduce the risk of injury or damage to the product, two people should be used for installation. These installation instructions are intended for use by qualified installers.
Installing the appliance Check the installation niche To ensure a safe, trouble-free installation and the best possible cosmetic result, check to be sure that the installation space complies with the installation requirements. Before installation ,Caution - the appliance is very heavy. Use caution when unpacking and opening the door, danger of tipping. ^ Check that the cavity is square. ^ To protect the base from damage during installation, attach a hard board, linoleum, etc.
Installing the appliance ^ Loosen the bracket that holds the appliance to the pallet. ,Caution! The appliance is no longer secured and may be unstable. ^ Unscrew the screws a on the cover b and pull off the sticker c. ^ Remove the cover b. ^ From the rear of the appliance carefully lift it from the pallet. Once the appliance is on the ground it can be wheeled around.
Installing the appliance ^ Connect the appliance to the power supply and turn it on. After several seconds the indicator light will come on. The indicator light will display different colors one after the other; any control light at the end indicates that the module was correctly installed. Preparing the installation niche Keep the appliance door closed until it is securely fastened in the niche. Tipping hazard. If the indicator light does not come on, installation of the module was unsuccessful.
Installing the appliance Anti-tip brackets The anti-tip brackets help keep the appliance safely secured to the installation niche to prevent tipping. Two anti-tip brackets are recommended for each appliance or appliance combination (side-by-side). ^ Drill pilot holes: 1 – /8" (3 mm) for 5 x 60 mm wood screws – 1 /16" (2 mm) for 4 x 15 mm wood screws The distance "D" between the anti-tip brackets b is the width of the appliance. ^ Tightly secure the anti-tip brackets in the niche.
Installing the appliance Securing an alternative anti-tip device – The beam must cover the appliance by at least 2" (50.8 mm). If the anti-tip brackets cannot be attached securely, an alternative anti-tip device can be used. Ensure that there is no "give" between the appliance and the anti-tip device. ^ Mark the installation height (lower edge of the beam) on the rear wall of the niche. If possible, always screw the wooden beam to existing studs.
Installing the appliance Sliding the appliance into the installation niche In the case of side-by-side installations, a separate outlet must be used for each appliance. ^ To prevent the power cord from becoming caught: Tie a piece of string to the middle of the power cord and feed it forward under the appliance. When sliding the appliance in, pull the cable forward c. ^ Carefully slide the appliance into the space until the height-adjustable wheels interlock with the anti-tip brackets d.
Installing the appliance Aligning the appliance ^ Align the appliance with the custom front. A mark is located on the appliance base and is used as a standard gauge for height adjustment. When adjusting the height, align this mark at 1 1/4" (32 mm) above the floor. ^ Place a marking-out level over the installation aids e on the door. ^ Unscrew the height-adjustable feet until the mark on the base has reached the indicated guide dimension 1 1/4" (32 mm).
Installing the appliance Note: – Do not twist or jam the appliance inside the niche. When unscrewing the height-adjustable feet, proceed gradually, alternating between left and right. – The adjustment of the rear feet is aided if the appliance is lifted at the rear (tipped forward slightly). – If using a wooden beam as an alternative anti-tip device, rotate the appliance all the way toward the wooden beam.
Installing the appliance For a side-by-side combination the filler strips from both appliances are put together to form one long filler strip: ^ Take the peg from the "side-by-side merging kit" and insert it halfway into the filler strip rail on the left-side appliance. ^ Place the second filler strip on the peg and press both filler strips together. ^ Insert both filler strips into the installation space above the appliance, until they click into place.
Installing the appliance Preparing the custom door ^ Open the appliance door. ^ Unscrew the installation supports n from the appliance door. ^ Loosen the remaining screws from the strips o on each side of the door, then remove. ^ Set aside the screws and side strips o - you will need them again later. ^ Remove the light switch cover (see arrow). 68 ^ Measure the distance X between the bracket from the door and the overhead furniture/fixtures. ^ Loosen the two nuts.
Installing the appliance The bracket includes a variety of holes for the various design options of custom doors. When performing work on the custom door, always observe the following: – Always select the best load-bearing surface of the custom door as the location for screws. – Always select a screw length that is shorter than the thickness of the door front. Attaching and aligning the custom door front ^ Mark the distance X on the back-side of the custom door.
Installing the appliance ^ Adjust the custom door to adjacent furniture/fixtures. Attaching the covers ^ Align the custom door with the double-threaded bolts. ^ Tighten the nuts on the adjusting rail. This will correct the side alignment of the door. ^ Put the side strips (15) back into place and screw them completely down on both sides of the appliance door.
Installing the appliance Attaching the toe-kick panel The maximum height of the toe-kick panel is 4" from the top of the floor. Do not cover the ventilation slits in the base panel. Risk of damage to the appliance. ^ Insert the cover strip into the space between the appliance and the side panel. For side-by-side combinations, the cover strips (on both sides of the appliance) are applied to the outermost spaces only. ^ If required, cut the toe-kick panel to the required length and height.
Installing the appliance Mounting the air separator ^ Open the freezer door. The air separator on the inside of the freezer door keeps the supply and exhaust air separate. This prevents warm exhaust air from flowing into the machine, optimizing the energy performance of the unit. ^ Wedge the air separator at the bottom of the freezer door, so it connects in place. ^ If necessary, shorten the three parts of the air separator. ^ Insert the foam pieces back into the sides.
Installing the appliance Aligning the Ice/Water Dispenser If necessary the depth of the Ice/Water dispenser can be aligned from inside the custom door cut-out. This allows the dispenser to be aligned with the custom door to achieve the best possible appearance. ^ Remove the cover and the plastic grill. ^ Press the dispenser back and pull downwards to remove. ^ Remove the screw from the rear casing, then lift the tab on the drip tray up and off.
Installing the appliance ^ Loosen the screws of the four clamps. ^ Pull the rear cover forward and out. ^ Insert a screwdriver into one of the four slots and push sideways until the dispenser is aligned with the custom door (the gray arrow will adjust to the rear; the black arrow will adjust front). ^ Re-tighten the screws of the clamps. ^ Insert the drip tray back into place, then clip the water sensors back onto the drip tray. ^ Replace the rear cover, panel and screw.
Installing the appliance Attaching the frame and the shelf For 3/4" (19 mm) thick custom doors: ^ Slide the cover frame onto the Ice/Water Dispenser and press until it is flush with the door surface (be sure the word "TOP" on the cover frame is upward). For 1 1/2" / (38 mm) thick custom doors: ^ Press the extension frame onto the cover frame. ^ Slide the cover frame onto the dispenser an press until the it is flush with the door surface (be sure the word "TOP" on the cover frame is upward).
Plumbing All plumbing work should be carried out by a suitably qualified and competent person, in accordance with all applicable local and national regulations. The manufacturer is not liable for damage to property due to an incorrect installation or water connection. The water quality must conform to country requirements for drinking water. – The appliance is only suitable for connection to the cold water supply. – The water pressure must be between 25 and 120 psi (1.72-8.25 bar).
Plumbing Preparing the water connection The connection to the household water supply must be installed before the appliance is installed. ^ Turn off the main water valve to prevent damage caused by leaking water. ^ Attach the connecting pipe to the shut-off valve, according to the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Install the connecting pipe.
Plumbing Connecting the water supply ^ Push the union nut and seal onto the water pipe. When connecting the water pipe to the solenoid valve of the appliance, follow the instructions supplied by the manufacturer of the ice cube maker installation kit. ^ Push the end of the water pipe into the appliance connection and screw on the union nut, 3. First tighten by hand. When bending the water pipe, be sure not to kink it, otherwise there is a risk of leaks and water damage. Use bending aids.
Electrical connection , Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
RemoteVision The Miele RemoteVision system is designed to send messages directly to Miele and/or your PC. For information on set-up and installation of the RemoteVision module see the "Installation" section of this manual. Be sure your wireless system meets the following requirements – Windows XP® or newer operating system, Mac® OS X 10.3 or higher – Cable or DSL modem – Microsoft® Internet Explorer 6 or higher, Safari 2.0 or higher, Firefox 1.
RemoteVision Accessing the RemoteVision control panel ^ Tap the X button until ; appears in the display. ^ Touch the access button "p" to confirm. ^ Touch the access button "p" so it turns yellow. ^ Note the position of the button X, but do not touch. ^ Touch the access button "p" again so it turns white. Only the access button "p" is visible. ^ Place one finger on the position of the X button and hold (the X button will not be visible). ^ While holding down the X button, press the access button "p" once.
RemoteVision MasterCool control panel options for RemoteVision Selectable options Description of function ;- Back ;2 Reboot the module ;3 Reset the module to factory settings ;4 Enter Ad-Hoc Mode Note: If you cannot select any option (other than ; - "back"), the module has not been installed correctly.
Alteration rights reserved / 3408 For the most updated manual see the Miele web site. M.-Nr.
