Quick Guide

Using for the first time Operation Drying Fragrance flacon
M.-Nr. 11 495 23000
3. Loading the tumble dryer
ĺ Open the door.
ĺ Unfold the laundry and load
loosely into the drum.
Do not overload the drum.
Overloading can cause
unnecessary wear and tear of
the laundry, give a disappointing
drying result and cause more
creasing.
If you are not using a fragrance
flacon: the tabs must be pushed
down completely (see arrows) to
ensure both sockets are closed.
ĺ Shut the door with a gentle
swing.
When closing the door, make
sure that laundry does not get
trapped in the door opening.
FragranceDos – the dryer has two
positions for inserting a fragrance flacon.
Use one or both whenever you want to
add a pleasant fragrance to your laundry.
Close the unused socket.
Before using a fragrance flacon, please
read "Warning and Safety instructions
- Using a fragrance flacon (optional
accessory)" and "Fragrance flacon" in
the operating instructions.
Inserting a fragrance flacon
1. 2.
3. 4.
Markers  and  must line up with
each other.
5. 6.
ĺ Turn the outer ring clockwise a little.
Markers  und  must line up with
each other.
Before drying
ĺ Turn the outer
ring clockwise
a little.
The further you open the flacon, the
more intense the fragrance.
After drying
To avoid the fragrance escaping
needlessly:
ĺ Turn the outer
ring anti-clock-
wise until
marker  is in
position .
When not in use, you can store the
fragrance flacon in its original
packaging.
Before cleaning the fluff filters
ĺ Remove the
fragrance
flacon.
ĺ Only store the
fragrance
flacon in its
original
packaging.
Never lay the fragrance flacon down.
Otherwise, the fragrance will leak out.
Changing the programme sequence
TWF 720 WP en - AU, NZ
1 Condensed water container
– Empty after every drying programme
2 Door
3 Control panel
4 Access panel for the heat exchanger and plinth filter
– Do not open during drying
5 Cool air intake grille
– Do not obstruct with a laundry basket or other objects
OPERATION
DRYING
CHANGING THE PROGRAMME SEQUENCE
3. Selecting a programme and starting it
Selecting a programme
ĺ Turn the programme selector.
– The dryer is switched on.
– A drying level may light up and durations will appear in
the time display.
Programmes with drying levels
– Cottons, Minimum iron, Delicates, Shirts, Express,
Denim, Bed linen, Pre-ironing
ĺ Touch the sensor for the drying
level you want. It then lights up
brightly.
Any drying level can be selected
for the Cottons, Express, and
Bed linen programmes. A lim-
ited range is available with the
other programmes.
Other programmes and timed drying programmes
– Cottons , Woollens handcare, Proofing
The drying level ⁄ duration is preset by the dryer
automatically and cannot be altered.
– Warm air
ĺ Touch the  sensor repeatedly
until the required programme
duration appears in the display.
You can set the duration in
10-minute increments from
0:20 minutes up to 2:00 hours.
ĺ You can reduce the duration with the  sensor.
1. Notes on correct laundry care
ɒDamage due to foreign objects.
Foreign objects left in the laundry can melt, burn, or
explode.
Ensure that any foreign objects (e.g. detergent
dispensing balls, lighters, etc.) have been removed from
the laundry.
ĺ Sort the laundry according to the type of fibre and
weave, size, garment care label symbol and the drying
level required.
ĺ Untangle the laundry.
ĺ Check seams and stitching to ensure that padding and
linings are intact.
ĺ Fasten duvet covers and pillow cases to prevent small
items from being rolled up inside them.
ĺ Fasten hooks and eyes.
ĺ Tie together textile belts and apron ties.
ĺ Sew in or remove loosened underwiring from bras.
Adding or removing laundry
You have forgotten an item of laundry, but
the programme has already started.
ĺ Touch the Start/Add laundrysensor.
Add* will light up in the time display.
ĺ Open the door.
ĺ Add or remove laundry.
ĺ Close the door.
ĺ Touch the Start/Add laundrysensor.
The programme will start.
* Exceptions:
In some cases, e.g. during the cooling
phase or in the Proofing programme, you
cannot add laundry.
– In these cases Add will not light up.
Cancelling or changing the current
programme
It is no longer possible to change the
selected programme. This prevents the
appliance being operated unintentionally,
e.g. by children.
If you adjust the programme selector, 
will light up in the time display.
 goes out when you select the original
programme again.
ĺ Turn the programme selector to the
position.
The programme is cancelled.
ĺ Select a new programme.
ĺ Touch the Start/Add laundrysensor.
Select Gentle tumble (if required).
Delicate fabrics (with the symbol on the
care label, e.g. acrylic garments) are dried
at a lower temperature with a longer
programme duration.
ĺ Touch the Gentle tumble sensor. It then
lights up brightly.
Selecting Delay start (if required)
With Delay start you can delay the start of
the programme by up to a maximum of
24hours.
Delay start cannot be used with the Warm
air programme.
ĺ Touch the .
It then lights up
brightly.
ĺ Touch the  or  sensors repeatedly
until the required Delay start time appears
in the display.
Starting a programme
ĺ Touch the flashing Start/Add laundry
sensor. It will light up.
Energy saving:
After 10 minutes the indicators dim and
the Start/Add laundry sensor starts
flashing.
ĺ Touch the Start/Add laundry sensor to
switch the indicators on again (this does
not have any effect on a running
programme).
4. Removing the laundry at the
end of the programme
End of programme:  lights up in the
time display and the Start/Add laundry
sensor goes out.
– Energy saving: After 10 minutes the
indicators dim and the Start/Add laundry
sensor starts flashing.
– The dryer will switch off automatically
15minutes after the end of the
Anti-crease phase (with programmes
without an Anti-crease phase it will switch
off 15minutes after the end of the
programme).
ɒDo not open the door before the end
of the programme.
ĺ Open the door.
ĺ Remove the laundry.
ɒCheck that all items have been
removed from the drum. If items are left
in the dryer, they could be damaged by
overdrying when the dryer is used the
next time.
If the dryer is switched on at the mains and
the door is opened, the drum lighting will
come on. It will go out after a few minutes
to save energy.
ĺ Turn the programme selector to .
ĺ Clean the fluff filters.
ĺ Shut the door with a gentle swing.
ĺ Empty the condensed water container.Adding laundry
You can add laundry.
ĺ Follow the instructions in "Changing the
programme sequence".
Energy saving tips
To avoid unnecessarily long drying times
and high consumption of energy:
– Spin the laundry at the maximum spin
speed in the washing machine.
Clean the fluff filters in the door and
in the door opening after every drying
cycle.
– Load according to the optimum
amount of laundry recommended for
the programme being used. This will
mean that the energy consumption for
the amount of laundry is at its most
economical.
– Make sure the room temperature is not
too high.
If there are other heat producing
appliances in the room in which the
tumble dryer is located, make sure the
room is well-ventilated and switch the
other appliances off, if possible.
1 Control panel
The 2, 4, 6 and 7 sensors react to
fingertip contact.
Selection is possible as long as the
respective sensor is illuminated.
– If a sensor is brightly lit, this means:
currently selected
– If a sensor is dimly lit, this means:
selection possible
2 Sensors for the drying levels
After selecting a drying level programme
with the programme selector: touch one
of the sensors to select a drying level.
3 Indicator lights   
–   light up if necessary:
see "Problem solving guide".
–  Perfect Dry:
The Perfect Dry system measures the
residual moisture present in the
laundry in programmes with selectable
drying levels and provides a more
precise drying result.
After starting the programme, this
message...
...will flash until the programme
duration has been determined, and
then go out.
...will light up when the selected
drying level is reached near the end of
the programme.
...will remain dark with the
following programmes: Woollens
handcare, Warm air.
4 Gentle tumble sensor
For drying temperature-sensitive textiles
with the  symbol.
5 Time display
The remaining programme duration will
be displayed in hours and minutes.
6 Sensors   
– After touching the sensor, a later
start time for the programme (Delay
start) can be selected.
– The  and  sensors are used for
selecting the duration of the Delay
start period or the duration of the
Warm air programme.
7 Start/Add laundry sensor
Touching the Start/Add laundrysensor
starts the selected programme. The
current programme can be interrupted to
add laundry. The sensor flashes slowly
as soon as it is possible for a
programme to be started and then lights
up constantly after the programme has
started.
8 Optical interface
For service technicians.
9 Programme selector
The programme selector can be turned
clockwise or anti-clockwise.
The dryer is switched on by selecting a
programme, and switched off by turning
the programme selector to the 
position.
ɒBefore using the tumble dryer for
the first time, ensure that it is correctly
installed and connected.
Please read the separate operating
instructions supplied with the appliance.
ɒDamage caused by switching the
appliance on too soon.
This can damage the heat pump.
After setting up the tumble dryer, wait for
at least one hour before starting a drying
programme.
Emptying the condensed water
container
Empty the condensed water container
after every drying programme.
The  indicator will light up when the
maximum level in the condensed water
container is reached.
To switch the  indicator light off: Open
and close the door while the dryer is
switched on.
Damage to the door and fascia panel.
The door and the fascia panel can be
damaged when removing the condensed
water container.
Always close the door completely.
ĺ Pull out the
condensed water
container.
ĺ To prevent water running out, keep it in a
horizontal position when carrying it. Hold
it at the front and at the back.
ĺ Empty the con-
densed water
container.
ĺ Replace the
container in the
dryer.
Do not drink condensed water. It can
cause health problems in people and
animals.