G1000 / G2000 Dishwashers Technical Information TECHNICAL INFORMATION G1000 / G2000 Dishwashers 1
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwasher - Table of Contents WARNINGS AND SAFETY INFORMATION ......................................................................10 1.0 CONSTRUCTION AND DESIGN...............................................................................11 1.1 Appliance Overview ................................................................................................................................................11 1.1.
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - Table of Contents (Continued) 4.3 4.4 4.5 4.6 4.2.8 Sensor Softener............................................................................................................................................38 4.2.9 Electronically Controlled Water Hardness (EGS) .......................................................................................39 4.2.10 Intelligent Tab Function ...............................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - Table of Contents (Continued) 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.4.8 5.4.9 5.4.10 5.4.11 5.4.12 5.4.13 5.4.14 5.4.15 5.5 Flowmeter (circuit board) – Removal .........................................................................................................84 Top Spray Arm Removal.............................................................................................................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - Table of Contents (Continued) 6.4 6.5 6.6 6.7 6.8 6.3.2 Inspira Series - G1180 & G2180 ................................................................................................................. 139 6.3.2.1 G1180 / G2180 - Programming Mode ...................................................................................... 139 6.3.2.2 G1180 / G2180 - Service Mode ........................................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - List of Figures Figure 1-1: Appliance Overview (Typical Integrated Unit)............................................. 11 Figure 1-2: Appliance Overview (Typical Fully Integrated (Vi) Unit) ............................. 12 Figure 1-3: Pre-Finished Dishwasher............................................................................ 14 Figure 1-4: Integrated Dishwasher.................................................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - List of Figures (Continued) Figure 5-4: Door Seal with Door.................................................................................... 70 Figure 5-5: Door Seal Installation.................................................................................. 74 Figure 5-6: Drip Pan Removal.......................................................................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - List of Tables Table 1-1: Table 1-2: Table 1-3: Table 1-4: Table 1-5: Controls Overview..........................................................................................................13 Overview of US Model Numbers....................................................................................19 Door Spring Summary ...................................................................................................
G1000 / G2000 Dishwashers Technical Information G1000 / G2000 Dishwashers - List of Tables (Continued) Table 6-34: G2420 / G2430 Programming Mode Options (Cont. from Table 6-33) (Cont. on Table 6-35) .................................................................................................155 Table 6-35: G2420 / G2430 Programming Mode Options (Continued from Table 6-34) ................156 Table 6-36: G2420 / G2430 Service Mode Options (Continued on Table 6-37) .............................
G1000 / G2000 Dishwashers Technical Information Warnings and Safety Information Service and repair work should only be carried out by suitably qualified persons in accordance with all appropriate local and national safety regulations. Before any service work is started, the appliance must be disconnected from the power supply. If it is necessary to tip the machine when working on the lower areas, it may only be tilted onto its back.
G1000 / G2000 Dishwashers Technical Information 1.0 Construction and Design 1.1 Appliance Overview 1.1.
G1000 / G2000 Dishwashers Technical Information 1.1.
G1000 / G2000 Dishwashers Technical Information 1.2 Controls Overview Controls on Miele dishwashers are categorized into four (4) types: Control Type Description Novotronic Each Novotronic model dishwasher can be operated with a single knob. Surface mounted design technology (SMD) allows Miele Novotronic components to be extremely durable and reliable. These controls are capable of performing hundreds of tasks, which cannot be handled by mechanical components.
G1000 / G2000 Dishwashers Technical Information 1.3 Types of Dishwashers 1.3.1 Pre-Finished Figure 1-3: Pre-Finished Dishwasher The pre-finished construction consist of a pre-assembled door panel and control panel; making it an ideal replacement unit. Available in white, black or stainless steel. 1.3.2 Integrated Figure 1-4: Integrated Dishwasher Integrated dishwashers ship with a separate control panel, and optional GDU (door) panel.
G1000 / G2000 Dishwashers Technical Information Figure 1-5: Fully Integrated (Incognito) (Vi) Dishwasher Fully Integrated Dishwashers are designed to blend into the surrounding cabinetry. The operator controls are only available when door is opened. Each dishwasher is shipped with a bracket for securing a custom cabinet panel. An optional Miele stainless steel SCVi panel is also available. 1.4 Technical Data 1.4.1 Electrical Information Power Requirements: 120 VAC, 60 Hz Rated Load: 12.
G1000 / G2000 Dishwashers Technical Information GND To ground connector. Hard wiring the dishwasher should only be done if required by electrical code. Do not cut the plug off the power supply cord / plug and connect it directly to the house wiring under any circumstances. This voids the warranty. For hard wiring, the power cord must be removed from the appliance by disconnecting the cord from the terminal box located at the lower left front of the dishwasher, behind the Toekick and Service Panel.
G1000 / G2000 Dishwashers Technical Information Figure 1-6: Dimensions For the latest product specifications, including product dimensions visit: Miele.com 1.
G1000 / G2000 Dishwashers Technical Information 1.5.1 Data Tag - Location Figure 1-7: Data Tag Location 1.5.2 Data Tag – Information Figure 1-8: Data Tag Information 1.
G1000 / G2000 Dishwashers Technical Information Figure 1-9: Model Numbering 1.6.
G1000 / G2000 Dishwashers Technical Information 1.7 Door Springs / Weights – Specifications Springs should always be installed in matching pairs Model Color G1xxx, freestanding, builtunder G2xxx, built under G1xxx, (I) (VI) G2xxx, (I) (VI) Orange Tensile strength Length (mm) (N) Approx. 230 150 Blue Approx. 290 157 Uncolored Green Approx. 320 Approx.
G1000 / G2000 Dishwashers Technical Information 1.8 Layout of Components (Typical) 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Reed switch salt, B8/2 Salt reservoir Solenoid valve (reactivation) Y38 Solenoid valve (water hardness) Y5 Sensor softener, 10N1 Heater relay, K1/1 Spray arm sensing (middle) 4N1 Reed switch rinse aid, B8/1 Combi-Dispenser solenoid, Y50 Flowmeter, B3/4 Module tray electronic, 1N1 Door contact switch, S24 Water Intake valve (water intake) Y2 Turbidity sensor, B3/10 15. 16.
G1000 / G2000 Dishwashers Technical Information 2.0 Installation Refer to the Residential Appliance Installation Manual.
G1000 / G2000 Dishwashers Technical Information 3.0 Commission and Operation 3.1 Door Handle / Lock – Prefinished & Integrated Models To open the door: Press the release inside the door grip (Figure 3-1). To close the door: Push door closed, until an audible click is heard. Figure 3-1: Door Handle Release Note If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. 3.2 Child Safety Lock Refer to Figure 3-2.
G1000 / G2000 Dishwashers Technical Information 3.3 Water Softener If your tap water hardness is above 8 grains per gallon (140 ppm), the water should be softened. If the Water Softener is needed (for select models only): The water softener sets automatically to the local water hardness. Note The water hardness level can be programmed manually. See Diagnostic Modes 6.1 or Operational Manual. If the water softener is needed the salt reservoir must be filled – refer to 3.3.1 through 3.3.2 for details.
G1000 / G2000 Dishwashers Technical Information The Salt Reservoir holds approximately 4.5 lbs (2 kg) of salt For models with salt reservoir located on the inner door 1. Open door and hold at an angle, so that the salt container can be completely filled. 2. Open salt reservoir by pressing the button in the direction of the arrow until the flap springs open - as shown in Figure 3-3. 3. Open the built in funnel, carefully fill with salt until water runs out. 4. Clean any excess and/or spilled salt. 5.
G1000 / G2000 Dishwashers Technical Information 3.4 General Operation 3.4.1 Novotronic Controls 1. Ensure the Spray Arms are not blocked. 2. Close the door. 3. Turn on the dishwasher. The “Start” Indicator will flash. 4. Select a wash program by turning the Program Selector to the left or right to the desired wash program. 5. Press the “Start” button. 3.4.2 Touchtronic & Navitronic Controls 1. Ensure the Spray Arms are not blocked. 2. Close the door. 3. Turn on the dishwasher.
G1000 / G2000 Dishwashers Technical Information Select the desired options; a √ check will appear next to the option selected. See Figure 3-7. Figure 3-7: Display (With Selected Options) When finished customizing the program, confirm with OK. Select Start. 3.4.3 Fully Integrated (Incognito) (Vi) Controls 1. Open the door. 2. Ensure the Spray Arms are not blocked. 3. Turn on the dishwasher. The main menu shows in the display (Figure 3-8).
G1000 / G2000 Dishwashers Technical Information 5. Select the desired options; a √ check will appear next to the option selected. See Figure 3-10. Figure 3-10: Display (With Selected Options) When finished customizing the program, confirm with OK. Select Start. Close the door. Note For specific program details and further information on operating the dishwasher refer to the model specific Operating Manual.
G1000 / G2000 Dishwashers Technical Information 4.0 Description of Function 4.1 Cabinet Construction The inner cabinet is constructed of stainless steel (1.4301) welded onto four (4) vertical U-section sub-frames. The cabinet is sound and heat-insulated with bitumen and/or mineral wool matting.
G1000 / G2000 Dishwashers Technical Information 4.2 Water Intake 4.2.1 WaterProof System (WPS) The Water Inlet Valve (Y2) consists of two (2) electro-mechanical valves mounted within a waterproof box located at the water connection (end of the water intake hose). The valves are mounted in physically and electrically in series to ensure that if one valve should fail (e.g. due to blockage caused by a foreign body) the water flow will still be switched off by the other valve.
G1000 / G2000 Dishwashers Technical Information The WaterProof System (WPS) consists of a number of interdependent safety features, which provide protection against water leakage. 1. Protection against solenoid valve leakage: Each water intake is controlled by an inlet valve. If this valve cannot close properly due to some defect or blockage by a foreign body, a second inlet valve ensures that the water supply is shut off. 2.
G1000 / G2000 Dishwashers Technical Information 4.2.3 Water Inlet Mixer Water is taken into the appliance via the inlet valve and the water inlet mixer, through the ion exchanger (water softener) into the sump. The water softener resin (for reactivation) is located at the bottom of the water inlet mixer. The assembly also contains the EGS valve (for the electronically controlled water softener) reactivation valve and a built in flow meter.
G1000 / G2000 Dishwashers Technical Information Figure 4-4: Water Inlet Mixer 33
G1000 / G2000 Dishwashers Technical Information Component List – Refer to Figure 4-4. 1. Flow Meter B3/4 2. Ball Valve 3. Water Reservoir – Softener Reactivation 4. Overflow 5. Non-return Device 6. Vent 7. Ion Exchanger 8. Water Outlet to Salt Container 9. Water Intake from Salt Container 10. Connection to Inlet Valve 11. Reactivation Valve 12. EGS Valve 13. Water Outlet to Sump 14. Cabinet Water Inlet A. Middle Spray Arm Sensor B.
G1000 / G2000 Dishwashers Technical Information 4.2.4 Water Inlet Mixer Without EGS 1. 2. 3. 4.
G1000 / G2000 Dishwashers Technical Information 4.2.5 Water Inlet Mixer wth EGS 1. 2. 3. 4.
G1000 / G2000 Dishwashers Technical Information 4.2.6 Water Inlet Mixer during Reactivation 1. 2. 3. 4.
G1000 / G2000 Dishwashers Technical Information 4.2.7 Flow Meter B3/4, Water Intake Quantity A Flow Meter B3/4 integrated in the Water Inlet Mixer monitors the water intake quantity. The water flow is measured in the hard water area. A permanent magnet located in the Flow Meter axle activates an external reed switch each time the axle rotates.
G1000 / G2000 Dishwashers Technical Information 4.2.9 Electronically Controlled Water Hardness (EGS) To prevent or avoid possible glass corrosion, the wash water hardness level should not exceed or fall below 3 gr/gal, in program steps with heating and 5 gr/gal in program steps without heating. With mains water hardness below 20 gr/gal. (In heating steps under 16 gr/gal) the Solenoid Valve Y5 is activated to add a proportion of hard mains water to the cabinet.
G1000 / G2000 Dishwashers Technical Information Note When selecting the function “2in1” or “3in1”, impulses dispense rinse aid (1 ml), to slowly empty the dispensing chamber. This is necessary since rinse aid remnants, depending on their chemical composition, can clump, or separate, under certain temperature and storage conditions. The additional rinse aid dispensed as the chamber is being emptied has a positive effect on the drying result.
G1000 / G2000 Dishwashers Technical Information 4.
G1000 / G2000 Dishwashers Technical Information 4.3.1 Circulation Pump 1 2 3a 3b Water Intake (suction area) Output to Middle Spray Arm Output to Top Spray Arm Output to Bottom Spray Arm Figure 4-9: Circulation Pump – Water Paths Water is passed to the spray arms via the circulation pump. There are two circulation pump versions depending on model. Circulation pump with slide shutter: MPEW (approx. 65 W) With spray arm alternation, the spray arms are only intermittently supplied with water.
G1000 / G2000 Dishwashers Technical Information Circulation pump without slide shutter: MPEH (approx. 85 W) With the circulation pump without the slide shutter, all three spray arms are supplied with water at the same time. The total water circulation rate is approx. 68 l/min. Approx. 15 l/min flow through the top spray arm, approx. 34 l/min through the middle spray arm and approx. 19 l/min through the bottom spray arm. This pump version does not have a speed sensor.
G1000 / G2000 Dishwashers Technical Information Note This system has an additional advantage. Good wash results are also ensured if the dishwasher load includes items with less than ideal shape (e.g. cups with deep bases) as the controlled additional water intake will replace the water that may be trapped in such pieces. This similarly applies if, e.g., a light plastic bowl should be turned over and filled inadvertently by the stream of water.
G1000 / G2000 Dishwashers Technical Information 4.3.3 Heating A ring heater element in the circulation pump housing heats the water. The heater element and circulation pump together form one component. This ensures that on models with spray arm alternation, heating can always be carried out whichever water path is currently being used.
G1000 / G2000 Dishwashers Technical Information NTC Sensor Resistance Values Temperature (° F) Resistance (kΩ) 32 35.979 41 28.519 50 22.766 59 18.281 68 14.774 77 11.982 86 9.787 95 8.048 104 6.653 113 5.523 122 4.608 131 3.856 140 3.243 149 2.745 158 2.333 167 1.990 176 1.704 185 1.464 194 1.262 199 1.157 203 1.
G1000 / G2000 Dishwashers Technical Information 4.3.5 Heater Pressure Switch, B1/13 The heater pressure switch B1/13 is located directly on the circulation pump and registers the water pressure when the pump is in operation. Using the pressure switch contacts, the heating is controlled via 2 poles. The heating is switched via a heating relay located before the pressure switch contacts in the circuit. Heating activation occurs during the wash and final rinse cycles.
G1000 / G2000 Dishwashers Technical Information 4.3.6 Turbidity Sensor (ECO Sensor III, Auto-sensor), B3/10 Dishwashers from the G 1000/G 2000 generation are provided with one of two turbidity sensors, depending on model: The ECO sensor III measures the turbidity of the water and based on this result, the wash blocks, temperatures and running times of automatic programs are modified. In addition to this, the Auto-sensor has a microprocessor to evaluate the particle measurement.
G1000 / G2000 Dishwashers Technical Information Figure 4-13: Turbidity Sensor The sensor is situated in the feed pipe to the top spray arm, as shown in Figure 4-13. The flow rate is approx. 15 l/min. In order to compensate for residues on the sensor and ageing of the optical system, the turbidity sensor must be recalibrated regularly. This process is carried out automatically by the electronic unit and cannot be modified in any way.
G1000 / G2000 Dishwashers Technical Information 4.3.7 Spray Arm Sensing Specific model dishwashers are equipped with a spray arm sensing system to alert the operator that the spray arm is obstructed by a large dish, or utensil etc.... A spray arm sensor(s) is / are fitted on the water intake to monitor the middle and / or lower spray arm(s) as shown in Figure 4-14. A small magnet is fitted on one end of the appropriate spray arm.
G1000 / G2000 Dishwashers Technical Information 4.3.8 Filter Combination with Micro Fine Filter 1 2 3 4 Crown Coarse Filter Large Surface Area Fine Filter Micro Fine Filter Filter Cap Figure 4-15: Filter Combination in Sump The circulation pump M6 pumps the wash water from the sump via the filter combination to the spray arms. The circulating wash water is filtered via 2 parallel paths.
G1000 / G2000 Dishwashers Technical Information 4.4 Dispensing 4.4.1 Combination Dispenser 1 2 Reed Switch Solenoid Figure 4-16: Combination Dispenser The dispenser contains a solenoid that is activated via pulses to dispense detergent and rinse aid. The first pulse opens the detergent dispenser flap. All following pulses then dispense rinse aid. During detergent dispensing the solenoid is activated by a brief pulse, and this opens the detergent dispenser flap. Rinse aid is dispensed in pulses.
G1000 / G2000 Dishwashers Technical Information 4.5 Drain System 4.5.1 Drain Pump The drain pump M8 is driven by a synchronous motor and located under the cabinet on the left next to the sump. It is directly activated by the electronic module. In case of fault, the drain pump M8 is also activated directly via the overflow float switch B8/3. The drain pump pumps the suds via the non-return valve and the drain hose to the on-site drain.
G1000 / G2000 Dishwashers Technical Information 4.6 Drying Depending on model and production time frame, the G1xxx/G2xxx series dishwashers are outlined below: 4.6.
G1000 / G2000 Dishwashers Technical Information Circulation Turbothermic drying (UTT) operates with two separate air paths: Condensing Circuit To get dishes dry, moisture has to be removed from the dishwasher cabinet. The moist, warm air in the cabinet is gradually cooled. Cold air can hold less moisture than warm air, and thus, in this cooling process condensation drops form, which settle in the coldest areas of this circuit.
G1000 / G2000 Dishwashers Technical Information 4.6.2 Circulation Turbothermic Drying (active): UTT Version 2 Note This system is installed in models Gx04x – Gx47x starting with production index 34/… Figure 4-18: Drying System UTT Version 2 The function of both versions of circulation Turbothermic drying is comparable. However, Version 2 has no condenser pocket. Therefore the dishwashing cabinet is completely closed – the openings, to which the condenser pocket is attached in Version 1, are eliminated.
G1000 / G2000 Dishwashers Technical Information 4.6.3 Fan Two different fan types are employed for the two different versions of circulation Turbothermic drying: Circulation Turbothermic drying (active): UTT Version 1 A split-pole motor (approx. 23 W) drives two impellers. One impeller directs cool air across the outer surface of the stainless-steel condensation surface foils. The second impeller transports steam from the cabinet to the condensation surfaces.
G1000 / G2000 Dishwashers Technical Information 5.0 Service and Maintenance 5.
G1000 / G2000 Dishwashers Technical Information 5.1.1 Side Panel – Removal 1. 2. 3. 4. Refer to Figure 5-2. Remove the three retaining screws - Item 1. Use needle nose pliers to press in the retainer on the corner tabs. Remove the side panel. Figure 5-2: Side Panel Removal 5.1.2 Drip Pan – Removal Warning Before tilting the machine onto its back, the following must be carried out: 1. Open the salt container cap briefly then close it firmly - to empty the mixer. 2. Pump water out of the cabinet. 3.
G1000 / G2000 Dishwashers Technical Information Warning Ensure that the intake and drain hoses are not crushed. FRONT Figure 5-3: Drip Pan Removal Important To ensure a proper ground connection, the screws with the serrated surface under their heads MUST be used to secure the drip pan to the connection strip.
G1000 / G2000 Dishwashers Technical Information 5.2 Door Figure 5-4: Door Panel 5.2.
G1000 / G2000 Dishwashers Technical Information 1. Remove the screw caps from the side of the door (2 each side). 2. Support the panel while loosening the 4 screws, Figure 5-5. 3. Lift / remove the panel from the appliance. Figure 5-5: Integrated Door Panel Screw Locations Important Loosen the screws – Do NOT completely remove them. During reassembly do NOT over tighten the screws. 5.2.
G1000 / G2000 Dishwashers Technical Information Note The front door must be completely assembled before performing the door adjustment. This includes the installation of the GDU panel or custom panel. 1. Remove the Toe Kick. 2. Refer to Figure 5-6. 3. Open the door about halfway. 4. Use a Torx T20 driver to adjust the tension. Important The door tension should be adjusted so the door stays where it is placed.
G1000 / G2000 Dishwashers Technical Information 5.2.3 Outer Door Panel – Removal Caution Support the outer panel while removing the retaining screws. 1. Remove the front panel (5.2.1). 2. Refer to Figure 5-7. 3. Open the door and remove the countersunk screws (Item 1) from the perimeter of the door. 4. Close the door and remove the door outer panel.
G1000 / G2000 Dishwashers Technical Information 5.2.4 Fascia Panel Removal Figure 5-8: Door Fascia Panel 1. Remove the retaining screws, Fig. 5-8, Item 1. 2. Slide the fascia panel upwards. Note When refitting, care must be taken with the following: • The fascia must be fitted before the switch buttons are refitted. • To secure the fascia panel, only short screws (countersunk self-tapping 3.9 x 14) may be used as otherwise the electronic unit holder could be damaged. 5.2.
G1000 / G2000 Dishwashers Technical Information Note Door hinges must be replaced in pairs. 1. 2. 3. 4. 5. 6. Remove the outer door panel (5.2.3). Remove the right and left side panels (5.1.1). Close the door. Relax the tension in the ropes of the tension springs. Refer to Figure 5-9. Disconnect the ropes from the tension springs - Item 1 (Use special tool Miele Mat. # 05054690 to decrease tension to spring). 7. Open the hinge by bending it upward - Item 2. 8. Disconnect the ground cable. 9.
G1000 / G2000 Dishwashers Technical Information Figure 5-10: Front Hinge Retaining Screw 12. Remove the front door hinge retaining screws (Figure 5-10 - Item 1). 13. Remove the side door hinge retaining screws (Figure 5-11 - Item 1). Figure 5-11: Side Hinge Retaining Screw 5.2.
G1000 / G2000 Dishwashers Technical Information 1. Remove the outer door panel (5.2.3). 2. Disconnect the connections from the dispenser 3. Remove the retaining screws (Figure 5-12, Item 1). 4. Release the retaining clips (2 on top & 1 on bottom) and press out the dispenser unit. 5. Ensure the new dispenser functions correctly using the service mode. Figure 5-12: Dispenser Removal 5.2.7 Cable Holder - Removal 1. 2. 3. 4. 5. 5.2.8 Remove the outer door panel (5.2.3).
G1000 / G2000 Dishwashers Technical Information 1. Remove the cable holder (5.2.7). 2. Remove the door seal. Note When fitting the door seal, make sure that the seal holder is fitted back in the double U shape of the door inner panel. Figure 5-13: Lower door seal holder 5.2.
G1000 / G2000 Dishwashers Technical Information Note Ensure the appliance is perfectly level. 1. 2. 3. 4. Open the door. Loosen the flat round screw. Adjust the locking plate – as necessary. Tighten the screw. Figure 5-14: Door Seal with Door Note Adjust the locking plate such that the door seal is not excessively crushed and not under excess pressure when the door is closed (see Figure 5-14, Item A). The locking plate can be adjusted by 1 mm in either direction. 5.2.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 6. 7. 8. Remove the outer door panel (5.2.3). Remove the retaining screw, Figure 5-15 - Item 1. Press down the retaining lugs with a screwdriver, Figure 5-15 - Item 2. Pull the door lock slightly to the front. Remove the side screws from the inner door panel. Remove the holding plate. Remove the door lock from the holding plate. Disconnect all plugs.
G1000 / G2000 Dishwashers Technical Information 2. Bend the retaining lug on the switch to the side. 3. Replace the switch. 5.2.12 Fully Integrated (VI) Lock with Door Contact Switch Removal 1. 2. 3. 4. 5. 6. 7. 5.2.13 Door outer panel removal (5.2.3). Fascia panel removal (5.2.4). Remove the screws from the sides of the door inner panel. Remove the lock retaining screw. Remove the holder with electronic unit. Remove the lock with door contact switch.
G1000 / G2000 Dishwashers Technical Information 5.3 Inner Cabinet 5.3.
G1000 / G2000 Dishwashers Technical Information Figure 5-17: Door Seal Installation 1. Open the door. 2. Remove the old seal. 3. Clean the groove around the cabinet. Note Coating the seal with water may simplify fitting, 4. Refer to Figure 5-17. 5. Press the new seal in the groove, starting at corners (positions 1). 6. Press the middle of seal (positions 2) into the groove under the locking plate, while pressing the seal into the corners. 7.
G1000 / G2000 Dishwashers Technical Information 1. Refer to Figure 5-1, as necessary. 2. Remove the screw caps. 3. Remove the retaining screws Figure 5-18: Toe Kick (Plinth) Removal 5.3.3 Cover Plate - Removal Warning Due to the close proximity of the terminal block the appliance must be unplugged before removing the cover plate. 1. Remove the toe kick (plinth) (5.3.2). 2. Remove the two cover retaining screws, Figure 5-19. 3. Remove the cover plate.
G1000 / G2000 Dishwashers Technical Information Figure 5-19: Cover Plate Removal 5.3.4 Connecting Strip (Lower Support) – Removal Important The connecting strip should only be removed with the appliance uninstalled, and positioned on its back. Do not attempt to remove the connecting strip with the appliance installed in an upright position. 1. 2. 3. 4. 5. 6. Remove the toe kick (plinth) (5.3.2). Remove the cover plate (5.3.3). Remove the drip pan (5.1.2) Remove the retaining screws, Figure 5-20.
G1000 / G2000 Dishwashers Technical Information Figure 5-20: Connecting Strip Removal Note Use care when removing the connecting strip as the electrical connector to the waterproof inlet valves are held in place by retainers mounted on the inside of the connecting strip. 5.3.5 Multi-Plinth Removal (Door Tension Spring Housing) 1. Side panel removal (5.1.1). 2. Connecting strip removal (5.3.4). Figure 5-21: Connecting Strip 3. Remove the connecting strip retaining screws, Fig. 5-21, Item 1. 4.
G1000 / G2000 Dishwashers Technical Information 5.3.6 Steam Condenser Removal 1. 2. 3. 4. 5. 6. 7. 8. Remove the right side panel; see Side panel removal (5.1.1). Remove the cutlery tray (if present). Unscrew the splash protection cap (connection piece to air duct) in the cabinet. Remove the vent screw. Remove the bottom basket. Remove the air duct (from the condenser). Release the retaining lugs between the condenser and fan, Fig. 5-22, Item 1. Remove the condenser.
G1000 / G2000 Dishwashers Technical Information 5. Release the retaining legs between the condenser and fan, Fig. 5-22, Item 1. 6. Pull the fan out of its connection to the condenser. Figure 5-22: Condenser and Fan Assembly Note When refitting, make sure that the retaining lugs between the condenser and fan engage properly. 5.3.8 Basket Runners - Removal Warning Do not lever the basket runner off in the 79 area of the bolts, since this could lead to permanent damage to the wash cavity.
G1000 / G2000 Dishwashers Technical Information 1. Open the door. 2. Remove the upper basket. 3. Pull the basket runner out far enough so that the clip (Figure 5-23, Item 1) between the bolt on the cabinet wall and the basket runner is visible. 4. Remove the retaining clip by pushing it upward. 5. Remove the basket runner. Figure 5-23: Retaining Clip Note In the event the retaining clip is damaged during removal, it must be replaced with a new clip. 5.3.9 Water Level Check 1.
G1000 / G2000 Dishwashers Technical Information 3. Do not cancel the program. Slowly open the door to observe the water level in the bottom of the wash cavity. If the water level is within close proximity of the filter handle (about 4 mm above the filter), sufficient water has been taken in, Figure 5-24. Figure 5-24: Water Level Reference 5.
G1000 / G2000 Dishwashers Technical Information Figure 5-25: Water Path Layout 5.4.
G1000 / G2000 Dishwashers Technical Information Note For the G1000 and G2000 series, green restrictors (4.1 l/min) must be fitted in the WaterProof System valve holder. 1. Shut off the water supply. 2. Disconnect the WPS at the plumbing supply connection. 3. Remove the sealing washer and filter from inside the WPS connection. Using a 5mm nut-driver; press and tilt the restrictor to the side; as shown in Figure 5-26. 4. Remove the Restrictor - Figure 5-27. 5.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 6. 7. 5.4.3 Shut off the water supply. Disconnect the WPS at the plumbing supply connection. Remove the left side panel (5.1.1). Remove the drip pan (5.1.2). Disconnect the hose from the water. Disconnect the electrical connection. Unclip the wiring from the retainers. Release the WPS retainer from the rear of the appliance and remove the WPS.
G1000 / G2000 Dishwashers Technical Information 5.4.6 Bottom Spray Arm Removal 1. Remove the bottom basket. 2. Remove the spray arm. 5.4.7 Feed Pipe with Turbidity Sensor – Top Spray Arm, Removal 1. 2. 3. 4. 5. 6. 5.4.8 Remove the right side panel; see Side panel removal ( 5.1.1). Disconnect the turbidity sensor plug connections. Top spray arm removal (5.4.4). Unscrew the counter nut. Drip pan removal (5.1.2). Disconnect the hose clip connection to the circulation pump.
G1000 / G2000 Dishwashers Technical Information Figure 5-28: Spray Arm Sensor 2. Remove the spray arm sensor, Fig. 5-28, Item 1. 3. Disconnect its plug connection. 5.4.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 6. 7. Unscrew the water inlet mixer vent connection inside the cabinet. Unscrew the salt container cap. Remove the sealing ring. Empty the salt container. Close the opening with the service cap (available through Miele). Unscrew the retaining nut. Remove the left side panel (5.1.1). Warning Do not tilt the unit onto its right side, as this would cause water to run into the fan. 8. Remove the drip pan (5.1.2). 9.
G1000 / G2000 Dishwashers Technical Information 1 2 3 4 5 Middle Spray Arm Sensor Flowmeter Circuit Board Lower Spray Arm Senso Solenoid for EGS Valve Solenoid for Reactivation Figure 5-29: Water Intake Mixer Assembly and Related Components 5.4.11 EGS Valve Solenoid - Removal 1. 2. 3. 4. 5. 6. 5.4.12 Remove the left side panel (5.1.1). Remove the drip pan (5.1.2). Remove the connecting strip (5.3.4). Disconnect the electrical connector from the solenoid.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 6. 5.4.13 Remove the left side panel (5.1.1). Remove the drip pan (5.1.2). Remove the connecting strip (5.3.4). Disconnect the electrical connector from the solenoid. Twist the reactivation valve 90° clockwise. Remove the reactivation valve upwards. Salt Container - Removal 1. 2. 3. 4. 5. 6. 7. 8. 9. Remove the salt container cap from the cabinet interior. Remove as salt water from the salt container. Remove the sealing ring.
G1000 / G2000 Dishwashers Technical Information 2. Remove the drip pan (5.1.2). 3. Disconnect the electrical connectors. 4. Disconnect the plumbing connections for the feed pipes to the top and middle spray arms. 5. Disconnect the plumbing connections between the circulation pump and the sump assembly. 6. Remove the circulation pump. Important When installing the circulation pump, the seal must be installed on the pump.
G1000 / G2000 Dishwashers Technical Information 1 2 3 4 5 6 7 Slide Shutter Motor Heater Pressure Switch Heater Element Speed Sensor Electrical Connection Capacitor Housing Cap Figure 5-30: Circulation Pump and Related Components (Typical) 5.4.
G1000 / G2000 Dishwashers Technical Information appliance. Refer to Figure 5-30, as directed. Important During reassembly of the circulation pump ensure: 1. 2. 3. 4. 5. 5.4.15.1 A new sealing ring is installed The sealing ring is seated correctly in the pump housing cap The pump housing cap is evenly seated The cap retaining screws are secure The fastening clips are pressed over the retaining lugs Pump Cap Removal / Heater Element – Access 1. Remove the cap retaining screws. 2.
G1000 / G2000 Dishwashers Technical Information Figure 5-31: Slide Shutter Assembly Note The slide shutter can only be removed or fitted when the drive cog wheel is turned with the double tooth in the position shown, see Fig. 5-31. 4. Turn the drive cog wheel to bring the double tooth to the desired position as follows: Insert a small screwdriver in one of the holes on the cam (linked to the slide shutter control motor). Turn the cam until the slide shutter can be removed. 5. Remove the slide shutter.
G1000 / G2000 Dishwashers Technical Information 2. Pump housing cap removal (5.4.15.1). 3. Slide shutter removal (5.4.15.2). Figure 5-32: Drive Cam 4. Remove the drive retaining screws, Fig. 5-27, Item 1. Warning! When refitting, check that the O-ring is seated correctly on the drive cam. Before refitting the slide shutter in the pump housing, make sure that the double tooth on the drive cog wheel points to the arrow on the housing.
G1000 / G2000 Dishwashers Technical Information 5.4.15.4 Pump Impeller Removal 1. Circulation pump removal (5.4.14). 2. Pump housing cap removal (5.4.15.1). 3. Hold the shaft base with suitable pliers and unscrew the pump impeller clockwise. 5.4.15.5 Pump Housing Removal 1. 2. 3. 4. 5. 6. 5.4.15.6 Capacitor Removal 1. 2. 3. 4. 5.4.15.7 Circulation pump removal (5.4.14). Pump housing cap removal (5.4.15.1). Pump impeller removal (5.4.15.4). Remove the retaining screws.
G1000 / G2000 Dishwashers Technical Information 1. Circulation pump removal (5.4.14). 2. Lift the PCB slightly with a pair of needle nose pliers so that it can be gripped with the hand. 3. Turn the PCB 90° clockwise and remove it. 5.4.16 Drain Pump Removal 1. Remove the non-return valve from the sump under the filter combination. 2. Cover plate removal (5.3.3). 3. Disconnect the pump plug connections. Figure 5-33: Drain Pump Retaining Clip 4. Open the safety retainer clip with a screwdriver, Fig.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 5. 6. 7. Open the door. Remove the bottom basket. Remove the filter combination. Remove as much residual water as possible from the sump and drain hose. Lay the dishwasher on its back. Drip pan removal (5.1.2). Pull off the float switch. Disconnect its plug connections. Note When refitting the float, make sure that the side with the Mat. No. faces downwards. 5.4.18 Sump Removal 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
G1000 / G2000 Dishwashers Technical Information Warning! To avoid possible leakages later, the clip on the sump should not be overtightened. 5.4.
G1000 / G2000 Dishwashers Technical Information 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 5.4.20 Open the door. Remove the bottom basket. Remove the bottom spray arm. Remove the filter combination. Remove as much residual water as possible from the sump and drain hose. Lay the dishwasher on its back. Remove Drip pan, 5.1.2 Disconnect the NTC temperature sensor plug connections. Remove the NTC temperature sensor. Remove the sealing ring.
G1000 / G2000 Dishwashers Technical Information 2. Place a screwdriver on the retaining clip spring, Fig. 5-34, and press against it. 3. Turn the handle clockwise and release the filter combination clip connection. 5.4.21 Filter Combination Assembly (New Micro Fine Filter and Handle) Note During assembly, the dishwasher is used as a guide. If a new micro fine filter and handle (crown coarse filter) are used, a locking piece is not required. 1. Place the micro fine filter in the sump.
G1000 / G2000 Dishwashers Technical Information Figure 5-36: Filter Combination Lock/Unlock Positions 4. Press the large surface area fine filter downwards, Fig. 5-36, Pos. 1. 5. Fit the handle (crown coarse filter) and turn it clockwise as far as possible, Fig. 536, Pos. 2. 6. Carry out a visual check: The handle (crown coarse filter) should be parallel to the door, Fig. 5-36. 7. Carry out a functional check: Remove the filter combination and refit it. 5.4.
G1000 / G2000 Dishwashers Technical Information Figure 5-37: Combination Filter Locking Clip (Unlocked) Figure 5-38: Combination Filter Locking Clip (Locked) 9. Fit the locking piece, Mat. No. 06248730, to prevent the retaining clip spring opening, see Fig. 37 and 38.
G1000 / G2000 Dishwashers Technical Information 5.
G1000 / G2000 Dishwashers Technical Information 5.5.1 Mains Switch Removal (Integrated) 1. 2. 3. 4. Fascia panel removal (5.2.4). Remove the screws from the sides of the door inner panel. Remove the middle screw from the top of the door inner panel. Tilt the holding plate to the front. Note If the dishwasher has a furniture front, take care to insert a towel or similar between its top edge and the fascia to prevent the risk of scratching. 5. Disconnect all plugs. Fig. 5-40: Mains Switch Removal 6.
G1000 / G2000 Dishwashers Technical Information 5.5.2 Electronic Unit Holder Removal 1. 2. 3. 4. 5. 6. 7. 5.5.3 Door outer panel removal (5.2.3). Fascia panel removal (5.2.4). Remove the screws from the sides of the door inner panel. Remove the door contact switch retaining screw. Disconnect all plug connections at the electronic unit. Remove the holder with electronic unit. Remove the lock with door contact switch. Electronic Unit Removal (Integrated) 1. Fascia panel removal (5.2.3). 2.
G1000 / G2000 Dishwashers Technical Information 6.0 Fault Diagnosis 6.1 Diagnostic Modes – Overview The G1000 / G2000 series dishwashers contain the following diagnostic modes: Customer Programming Mode, Service Programming Mode and Service Mode. Access to the different modes varies by model number. Functions, settings and parameters vary by model number. Refer to the model specific information contained in this section. USA Models are listed as follows: Section Series Model Number 6.
G1000 / G2000 Dishwashers Technical Information 6.1.1 Water Hardness Setting – Checking and Programming Access the programming mode. The display shows P and the set value alternately. Setting range: P0 to P70 = Water hardness. E.g. P15 (standard setting) corresponds to 15 gr/gal, (15°d), see Table 6-2.
G1000 / G2000 Dishwashers Technical Information Acknowledgement Indicator Successful accessing of the Service Dept. programming mode is indicated by a rapid flashing Start/Stop LED (5 Hz) Options Refer to Tables: 6.3 through 6-6. Control Dial Function Position 1 o’clock Programming Display Pos. 1 Reset Flashing Rhythm of Rinse LED Turn the control dial With this program Long to the 1 o’clock function, all position.
G1000 / G2000 Dishwashers Technical Information Control Dial Position Function Programming Display Flashing Rhythm of Rinse LED Pos. 12: To move through With this Long Short Resetting the levels, turn the programming standard settings control dial to the function, all 11 o’clock position. parameters that can be modified by Press the Start/Stop button the customer, can 1x. Turn the Control be reset to the dial to the 9 o’clock factory setting. If position.
G1000 / G2000 Dishwashers Technical Information Control Dial Position 11 o’clock Function Programming Pos. 22: Program To move through the running time levels, turn the control reduction dial to the 11 o’clock position. Press the Stop/Start button 3x. Turn the control dial to the 6 o’clock position. To change the setting, press the Start/Stop button.
G1000 / G2000 Dishwashers Technical Information Control Dial Position Function Programming Display Flashing Rhythm of Rinse LED To move through Options: Rinse LED Long the levels, turn the is off = standard control dial to the machine height 11 o’clock position. (G1xxx); Rinse LED flashes = XXL units Press the Start/Stop button (G2xxx) 5x. Turn the control dial to 9 o’clock position. To change the setting, press the Start/Stop button. Pos.
G1000 / G2000 Dishwashers Technical Information *1 If the dishwasher is hooked up to an external softener system, which operates on the ion exchange principle (meaning salt reactivation), the water hardness supplied by that system has to be set. If this value is not known, set to 10 gr/gal. *2 If the electronic unit is replaced during service work, it must be programmed as follows: First set the country version and model version, then switch the dishwasher off.
G1000 / G2000 Dishwashers Technical Information Control Dial Position 1 o’clock Function Programming Display Flashing Rhythm of Rinse LED Pos. 1: Fault Turn the control dial If the Rinse LED is Long off, no faults are memory to the 1 o’clock display position. While the registered. The Rinse LED flashes, flashing rhythm of make a note of the the Rinse LED indicates which fault code, then press the Start/Stop faults are registered 1 button. If the same in the fault memory.
G1000 / G2000 Dishwashers Technical Information Control Dial Position Function Programming Display 3 o’clock Flashing Rhythm of Rinse LED Component Turn the control dial The flashing rhythm Long Short Display test to the 3 o’clock of the Rinse LED U0 position. To start indicates which 1 U1 the component test, component test is 2 U2 or to access the activated. For the 3 U3 next component to sequence of 4 U4 be tested, press the component testing 5 U5 Start/Stop button.
G1000 / G2000 Dishwashers Technical Information 6.2.1.3 G2020 Component Test – Information After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1. R1, Y2, M6, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. a Note During the period when the auxiliary winding relay is activated, a higher circulation pump current of approx. 0.
G1000 / G2000 Dishwashers Technical Information 6.2.2 Advanta Series – G2170 6.2.2.1 G2170 - Programming Mode Initial requirements 1. Open the door. 2. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button. 4. Immediately press and release the program button 5 times and at the 5th time hold until the Rinse & Hold LED flashes rapidly. 5. Release the program button If the Rinse & Hold LED has not started to flash within approx.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Intake/Drain Lt. Function Long Short Pos. 0: Long - - Indication Flashing Rhythm of SaniWash LED The Sani-Wash Long Short Display LED is off or flashes. Shows the ID No. software version ID No., e.g. -769 Press the Program The Intake/Drain Short Pos. 1: Long Short Display button 1x. LED flashes 1x Reset briefly intermittently. With this programming P0 function, all parameters can be reset to delivery condition.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Intake/Drain Lt. Function Long Short Pos 3: Set amount of rinse aid dispensed - 3 Pos 4: Buzzer on/off - 4 Programming Indication Flashing Rhythm of SaniWash LED Press the Program The Intake/Drain Long LED flashes 3x button 3 times. To modify the rapidly dispensing amount, intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Intake/Drain Lt. Long Short Pos. 12: Reset to factory setting 1 2 Long Short Pos. 20: Set the wash temperatu re 2 - Indication Flashing Rhythm of SaniWash LED Press the Program The Intake/Drain Long Short Display LED flashes 1x long button 12x To reset all and 2x briefly parameters to intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Indication Intake/Drain Lt. Long Short Pos. 22: Press the Program The Intake/Drain Program button 22x running time reduction 2 2 Long Short Pos. 23: Water quantity normal / increased 2 3 LED flashes 2x long and 2x briefly intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Intake/Drain Lt. Programming Indication Long Short Pos. 26: Flashing Rhythm of SaniWash LED Press the Program The Intake/Drain Long Short Display Add second button 26x. LED flashes 2x interim rinse To change the long and 6x briefly setting, press the intermittently. P0 The SaniWash Program button and hold it until the LED is off = Intake/Drain LED program cycle per 2 6 flashes.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Indication Intake/Drain Lt. Press the Program The Intake/Drain Long Short Pos. 39: Country variant setting *1 3 9 button 38x. LED flashes 3x long and 8x briefly intermittently. To change the The flashing rhythm setting, press the of the SaniWash Program button LED shows which and hold it until the country variant is Intake/Drain LED set: 1x = Europe; flashes.
G1000 / G2000 Dishwashers Technical Information 6.2.2.2 G2170 - Service Mode Initial requirements 1. Open the door. 2. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button. 4. Immediately press and release the program button 3 times and at the 3rd time hold until the Rinse & Hold LED flashes rapidly. 5. Release the program button If the Rinse & Hold LED has not started to flash within approx. 4 sec.
G1000 / G2000 Dishwashers Technical Information Flashing rhythm of Intake/Drain LED Long - - Function Short Pos. 0: - Software version ID check Pos. 1: Fault memory display and deletion 1 Programming Indication Do not press the Program button. The Intake/Drain LED is off. Press the Program button 1x. If the fault is indicated in the SaniWash LED, check if additional faults are registered. Press the Program button and hold it until the Intake/Drain LED flashes. Then press the Program button briefly.
G1000 / G2000 Dishwashers Technical Information Flashing rhythm of Intake/Drain LED Long Short - Function Pos 4: Operating hours check 3 Pos. 5: Control Panel LED test - 4 Pos. 6: Control Panel Buzzer Test Programming Indication Press the Program button 3x. To check the operating hours, press the Program button and hold until the Intake/Drain LED flashes. Then press the Program button briefly. *1 Press the Program button 4x.
G1000 / G2000 Dishwashers Technical Information 6.2.2.3 G2170 Component Test – Information After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1. R1, Y2, M6,…, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec Note During the period when the auxiliary winding relay is activated, a higher circulation pump current of approx. 0.
G1000 / G2000 Dishwashers Technical Information 6.3 Inspira Series 6.3.1 Inspira Series - G2140 & G2150 6.3.1.1 G2140 / G2150 - Programming Mode Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Release the Start/Stop button. 4. Immediately press and release the Start/Stop button 5 times and at time hold until the Start/Stop LED flashes rapidly. 5. Release the Start/Stop button the 5th If the Start/Stop LED does not flash, repeat the procedure.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Intake/Drain Lt. Long Short Pos. 0: Display The Rinse LED is off Long Short Display or flashes. Shows the software version ID No. ID No., e.g. –769. The Rinse LED is off Long Short Display or flashes. This programmable function can be used to reset all modifiable P0 parameters (both customer and service programming) to the standard settings.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Intake/Drain Lt. The Rinse LED is off Long Short Pos. 12: Press the Flashing Rhythm of Sani-Wash Lt. Long Short Display or flashes. This programmable function can be used to reset all P0 parameters that can be modified by the customer to the standard settings: P0 1 2 = Non-standard settings have been made; P1 = All settings reset to 1 P1 standard settings or no modifications have been made. Long Short Pos.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Intake/Drain Lt. Press the Program Long Short Pos. 23: Display Flashing Rhythm of Sani-Wash Lt. The Rinse LED is Long Short Display button 22 times. The off or flashes. The Rinse & Hold LED display shows P P0 flashes 2 times slowly and a digit and 2 times rapidly alternately: P0 = intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Intake/Drain Lt. Press the Program The Rinse LED is off Long Short Pos. 38: Flashing Rhythm of Sani-Wash Lt. Long Short Display or flashes. Individual setting possibilities depend on model and P0 whether a circulation pump with slide shutter (WAW) and sensor softener (SEH) 3 8 are fitted as follows: P0 = G12xx, G22xx (without WAW, without 1 P4 SEH); P4 = Australian version G12xx, G22xx (with WAW, without SEH).
G1000 / G2000 Dishwashers Technical Information 6.3.1.2 G2140 / G2150 Service Mode Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Release the Start/Stop button. 4. Immediately press and release the Start/Stop button 3 times and at the 3rd time hold it until the Start/Stop LED flashes. 5. Release the Start/ Stop button If the Start/Stop LED has not started to flash within approx. 4 sec., the accessing procedure must be repeated.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Intake/Drain Lt. Long Short Pos. 0: Software version ID check Long Short Pos. 1: Fault memory display and deletion - 1 Programming Display Flashing Rhythm of Rinse LED Do not press the The Rinse LED is Long Short Display Program button. off. Shows the The Rinse & Hold software version ID LED is off. No., e.g. -769 Press the Program The Rinse LED is Long Short Display button once.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Intake/Drain Lt. Programming Display Flashing Rhythm of Rinse LED Press the Program The Rinse LED Long Short Display Component button 2 times. The shows which U0 test Rinse & Hold LED component is being tested: For example flashes 2 times 1 U1 if the drain pump rapidly intermittently. Press M8 is being tested, 2 U2 the Rinse LED the Start/Stop 3 U3 flashes 3x briefly button. Press it again to activate the intermittently.
G1000 / G2000 Dishwashers Technical Information 6.3.1.3 G2140 / G2150 Component Test - Information After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec Note During the period when the auxiliary winding relay is activated, a higher circulation pump current of approx. 0.
G1000 / G2000 Dishwashers Technical Information 6.3.2 Inspira Series - G1180 & G2180 6.3.2.1 G1180 / G2180 - Programming Mode Initial requirements 3. Open the door. 4. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button. 4. Immediately press and release the program button 5 times and at the 5th time hold until the Rinse & Hold LED flashes rapidly. 5.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Intake/Drain Lt. Function Long Short Pos. 0: - Long - - Programming Indication Flashing Rhythm of SaniWash LED The Sani-Wash Long Short Display LED is off or flashes. Shows the ID No. software version ID No., e.g. -769 Press the Program The Intake/Drain Short Pos. 1: Long Short Display LED flashes 1x Reset button 1x. briefly To reset all intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Intake/Drain Lt. Long - Long - Short Function Pos 3: Set amount of rinse aid dispensed 4 Indication Press the Program The Intake/Drain button 3 times. LED flashes 3x rapidly intermittently. To modify the dispensing amount, press the Program button and hold it until the Intake/Drain LED flashes. Then use the Program button to enter the desired setting changes.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Indication Intake/Drain Lt. The Intake/Drain Press the Long Short 1 2 Pos. 12: Reset to factory setting Program button LED flashes 1x long and 2x briefly 12x intermittently. With To reset all this programming parameters to function, all factory setting, parameters that can press the be modified by the Program button customer can be and hold it until reset to the factory the Intake/Drain setting. LED flashes.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Indication Intake/Drain Lt. Press the The Intake/Drain Long Short Pos. 22: Program button LED flashes 2x long Program and 2x briefly running time 22x intermittently. reduction 2 2 Long Short Pos. 23: Water quantity normal / increased 2 3 The SaniWash LED is off = normal program cycle (factory setting); the SaniWash LED flashes = shortened program cycle.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Intake/Drain Lt. Programming Indication Flashing Rhythm of SaniWash LED Press the Program The Intake/Drain Long LED flashes 2x Add second button 26x. long and 6x briefly interim rinse To change the intermittently. setting, press the The SaniWash Program button and hold it until the LED is off = 2 6 Intake/Drain LED program cycle per flashes.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Intake/Drain Lt. Function Long Short Pos. 38: Model variant setting *1 3 8 Long Short Pos. 39: Country variant setting *1 3 9 Programming Indication Flashing Rhythm of SaniWash LED Press the Program The Intake/Drain LED flashes 3x button 38x. To change the long and 8x briefly setting, press the intermittently. Program button and hold it until the The SaniWash Intake/Drain LED LED is off = Gx18x flashes.
G1000 / G2000 Dishwashers Technical Information 6.3.2.2 G1180 / G2180 - Service Mode Initial requirements 3. Open the door. 4. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button. 4. Immediately press and release the program button 3 times and at the 3rd time hold until the Rinse & Hold LED flashes rapidly. 5. Release the program button If the Rinse & Hold LED has not started to flash within approx. 4 sec.
G1000 / G2000 Dishwashers Technical Information Flashing rhythm of Intake/Drain Function LED Long Short Pos. 0: Software version ID check Pos. 1: Fault memory display and deletion - Programming Indication Do not press the Program button. The Intake/Drain LED is off. The Sani-Wash LED is off or flashes. Shows the software version ID No., e.g. -769 Press the Program button 1x. If the fault is indicated in the SaniWash LED, check if additional faults are registered.
G1000 / G2000 Dishwashers Technical Information Flashing rhythm of Intake/Drain LED Long Short - - 4 5 Function Pos 4: Operating hours check Pos. 5: Control Panel LED test Programming Indication Press the Program button 3x. The Intake/Drain LED flashes 3x. To check the operating hours, press the Program button and hold until the Intake/Drain LED flashes. Then press the Program button briefly. *1 Press the Program button 4x.
G1000 / G2000 Dishwashers Technical Information 6.3.2.3 G1180 / G2180 – Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1. R1, Y2, M6,…, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Note During the period when the auxiliary winding relay is activated, a higher circulation pump current of approx. 0.
G1000 / G2000 Dishwashers Technical Information 6.4 Optima Series 6.4.1 Optima Series – G2420 & G2430 6.4.1.1 G2420 / G2430 – Programming Mode Initial requirements 1. Close the door. 2. Switch off the machine. Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Release the Start/Stop button. 4. Wait for dot in display, then immediately press and release the Start/Stop button 5 times and on the 5th time hold until the Start/Stop LED flashes rapidly. 5.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Delay Start LED Do not press the The Rinse LED is Long Short Pos. 0: Software version ID check Flashing Rhythm of Rinse LED Long Short Display Delay start button. off or flashes. The The Delay start display shows the LED is off. software version ID No., e.g. –769. Press the Delay The Rinse LED is Long Short Pos. 1: Long Short Reset start button once. off or flashes.
G1000 / G2000 Dishwashers Technical Information Flashing Flashing Rhythm of Rhythm of Function Programming Display Rinse LED Delay Start LED Press the Delay The Rinse LED is off or Long Short Display Long Short Pos. 5: flashes. The display start button 5 times. The Delay shows P and a digit alternately: P0 = start LED P0 flashes 5 times Normal program sequence (standard rapidly setting); P1 = Modified intermittently. program sequence.
G1000 / G2000 Dishwashers Technical Information Flashing Flashing Rhythm of Rhythm of Function Programming Display Rinse LED Delay Start LED Press the Delay start The Rinse LED is off Long Short Display Long Short Pos. 21: button 21 times. The or flashes. The display shows P and Delay start LED flashes 2 times slowly a digit alternately: P0 P0 = Standard setting; and once rapidly intermittently. Press P1 = Final rinse the Start/Stop button temperature 2 1 increased.
G1000 / G2000 Dishwashers Technical Information Flashing Flashing Rhythm of Rhythm of Function Programming Display Rinse LED Delay Start LED Press the Delay start The Rinse LED is Long Short Display Long Short Pos. 25: Pre-wash activation / deactivation (from software version ID no.-818) button 25 times. The Delay start LED flashes 2 times slowly and 5 times rapidly intermittently. Press 2 5 the Start/Stop button as appropriate to make the desired setting. Press the Delay start Long Short Pos.
G1000 / G2000 Dishwashers Technical Information Flashing Flashing Rhythm of Rhythm of Function Programming Display Delay Start Rinse LED LED Press the Delay The Rinse LED is off Long Short Display Long Short Pos. 38: Model start button 38 or flashes. The variant times. The Delay display shows P and setting (from start LED flashes 3 a digit alternately. software times slowly and 8 Individual setting version ID times rapidly possibilities depend no. –818) *1 intermittently.
G1000 / G2000 Dishwashers Technical Information 6.4.1.2 G2420 / G2430 - Service Mode Summary Initial requirements 1. Close the door. 2. Switch off the machine. Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Release the Start/Stop button. 4. Immediately press and release the Start/Stop button 3 times and at time hold until the Start/Stop LED flashes. 5. Release the Start/ Stop button the 3rd If the Start/Stop LED has not started to flash within approx. 4 sec.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Delay Start LED Do not press the The Rinse LED is Long Short Pos. 0: Software version ID check Flashing Rhythm of Rinse LED Long Short Display Delay start button. off. The Display The Delay start shows the software Led is off. version ID No., e.g. -769 The Rinse LED is Long Short Display Long Short Pos. 1: Fault Press the Delay memory start button once. off or flashes.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Delay Start LED Press the Delay The display shows Long Short Pos 2: - 2 Component start button 2 which component is test times. The LED being tested. For flashes 2 times example if the drain rapidly pump M8 is being intermittently. Press tested, U and 3 are the Start/Stop shown alternately. button.
G1000 / G2000 Dishwashers Technical Information 6.4.1.3 G2420 / G2430 Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1. R1, Y2, M6,…, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Warning! The circulation pump must not run for more than 30 sec. without water.
G1000 / G2000 Dishwashers Technical Information U13. Y38, reactivation valve: The reactivation valve is activated for 60 sec. U14. M2, fan: The fan is activated for 60 sec. U15. Vacant U16. Vacant U17. Vacant 6.4.2 Optima Series – G1470 & G2470 6.4.2.1 G1470 / G2470 Programming Mode Initial requirements 1. Open the door. 2. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button when the decimal point is in the display. 4.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Gel LED Do not press the The display shows Long Short Pos. 0: Software version ID check Long Short Pos. 1: 1 Reset Flashing Rhythm of Sani-Wash LED Long Short Display Gel button. The Gel the software LED is off. version ID No., e.g. -769 Press the Gel This programmable Long Short button once. The function can be Gel LED flashes used to reset all once rapidly modifiable intermittently.
G1000 / G2000 Dishwashers Technical Information Flashing Display Rhythm of Function Programming Gel LED Press the Gel The display shows Long Short Pos 4: Buzzer on/off Flashing Rhythm of Sani-Wash LED Long Short Display button 4 times. The P and a digit Gel LED flashes 4 alternately: P0 = times rapidly Buzzer off; P1 = P0 intermittently. Press Buzzer on. 4 the program button as appropriate to make the desired 1 P1 setting. Press the Gel The display shows Long Short Display Long Short Pos.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Gel LED Press the Gel The display shows Long Short Pos. 20: Wash temperature modification (from software version ID No. –984) Flashing Rhythm of Sani-Wash LED Long Short Display button 20 times. P and a digit The Gel LED alternately. Setting flashes 2 times options: P0 = P0 slowly Standard setting; intermittently. Press P1 = Wash the program button temperature 2 as appropriate to increased.
G1000 / G2000 Dishwashers Technical Information Flashing Rhythm of Function Programming Display Delay start LED Press the Gel button The display Long Short Pos. 24: 2 4 Soak activation / deactivation (from software version ID no. 818) Long Short Pos. 25: Pre- 2 5 wash activation / deactivation (from software version ID no. 818) Long Short Pos. 26: 2 6 Second interim rinse selection (from software version ID No. –984) Long Short Pos. 27: 2 7 Extended drying time (from software version ID no.
G1000 / G2000 Dishwashers Technical Information Table 6-41: G1470 / G2470 Programming Mode Options (Cont. from Table 6-40) (Cont. on Table 6-42) Flashing Rhythm of Function Programming Display Delay start LED The display shows Press the Gel Long Short Pos. 38: Flashing Rhythm of Rinse LED Long Short Display P and a digit button 38 times. alternately. The Gel LED Individual setting flashes 3 times slowly and 8 times possibilities depend on model and rapidly intermittently.
G1000 / G2000 Dishwashers Technical Information 6.4.2.2 G1470 / G2470 – Service Mode Initial requirements 1. Open the door. 2. Switch off the machine. Accessing 1. Press and hold the program button. 2. Switch on the machine. 3. Release the program button when the decimal point is in the display. 4. Immediately press and release the program button 3 times and at the 3rd time hold until the Rinse & Hold LED flashes. 5. Release the program button.
G1000 / G2000 Dishwashers Technical Information Function Programming Display Pos. 0: Do not press the Gel button. The Software Gel LED is off. version ID check Pos. 1: Fault Press the Gel button once. The Gel memory display LED flashes once rapidly and deletion intermittently. Press the program button. Press it again to display fault codes that may have been saved. To delete the fault memory, press the program button again and hold it until F and 0 are shown alternately Pos.
G1000 / G2000 Dishwashers Technical Information 6.4.2.3 G1470 / G2470 Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: U1. R1, Y2, M6,…, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information U6. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Warning! The circulation pump must not run for more than 30 sec. without water.
G1000 / G2000 Dishwashers Technical Information U14. M2, fan: The fan is activated for 60 sec. U15. Vacant U16. Vacant U17. Vacant 6.5 Excella Series 6.5.1 Excella Series – G2630 6.5.1.1 G2630 Programming Mode Initial requirements 1. Close the door. 2. Switch off the machine. Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Once the “Miele welcome” display appears release the Start/Stop button. 4.
G1000 / G2000 Dishwashers Technical Information Options Refer to Tables: 6-44 through 6-48. Function Programming Display Use the cursor buttons as This programmable function can appropriate to select Reset, be used to reset all parameters Pos. 1: Reset then press the OK button. Use (both customer and service the cursor buttons to make the programming) to the standard desired setting. settings. Use the cursor buttons as appropriate to select The display shows the available Pos.
G1000 / G2000 Dishwashers Technical Information Function Programming Pos. 7: Sensor wash program modification (from software version ID no. 984) Pos. 8: Main menu modification Display Use the cursor buttons as The display shows the options On and appropriate to select Off. This function is used to adjust the Adjust sensor wash, then Sensor wash program parameters so it press the OK button.
G1000 / G2000 Dishwashers Technical Information Function Pos. 13: Buzzer activation / deactivation and volume setting Pos. 14: Audible confirmation signal activation / deactivation Pos. 15: Brightness setting Programming Display Use the cursor buttons as appropriate to select Buzzer, then press the OK button. Use the cursor buttons to make the desired setting. The display shows the options Off, Normal and Loud. The function is activated as standard 5).
G1000 / G2000 Dishwashers Technical Information Programming Display Pos. 20: Resetting standard settings Function Use the cursor buttons as appropriate to select Factory default, then press the OK button. Use the cursor buttons to make the desired setting. Pos. 21: Wash/Final rinse temperature modification (from software version ID no. 984). Main wash Use the cursor buttons as appropriate to select Temperatures, then press the OK button. Use the cursor buttons to make the desired setting.
G1000 / G2000 Dishwashers Technical Information Function Programming Pos. 27: Machine height setting3) Use the cursor buttons as appropriate to select Appliance height, then press the OK button. Use the cursor buttons to make the desired setting. Use the cursor buttons as appropriate to select Country version, then press the OK button. Use the cursor buttons to make the desired setting. Use the cursor buttons as appropriate to select Model type, then press the OK button.
G1000 / G2000 Dishwashers Technical Information 6.5.1.2 G2630 – Service Mode Initial requirements 1. Close the door. 2. Switch off the machine. Accessing 1. Press and hold the Start/Stop button. 2. Switch on the machine. 3. Once the “Miele Welcome” display appears, release the Start/Stop button. 4. Immediately press and release the Start/Stop button 3 times and at the 3rd time hold until the programmable functions appear in the display. Note If the Start LED does not switch off within approx. 10 sec.
G1000 / G2000 Dishwashers Technical Information Function Software version ID check Programming Select ID no. with the OK button. Display The display shows version ID no. for the selection-display module (BAE) *1 and controlpower module (SLT) *2 Fault memory Use the cursor buttons to select The display shows saved fault display Fault memory. To return to the messages. If several faults main menu select Back, press have been registered, they will the OK button. be indicated one after the other.
G1000 / G2000 Dishwashers Technical Information 6.5.1.3 G2630 Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: V01. R1, Y2, M6, …, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information V06. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Warning! The circulation pump must not run for more than 30 sec. without water.
G1000 / G2000 Dishwashers Technical Information Starting with software version ID 984 the reactivation component test operates as follows: At the start of the mini-program the drain pump M8, water inlet valve Y2 and EGS valve Y5 are activated at the same time. M8 pumps water for 30 sec. and is primed with pulsed priming (2 sec. on/2 sec. off). Y2 and Y5 are switched off when 250 ml has been reached or 60 sec. has elapsed. The reactivation valve Y38 is then activated for 150 sec.
G1000 / G2000 Dishwashers Technical Information V17. 5N1, M6, wash sequence with bottom spray arm sensor (mini program): This starts with 30 sec. drainage, which begins with pulsed priming (2 sec. on / 2 sec. off). The water inlet valve is then activated (on models with and without slide shutter) until 5.4 l has been taken in. At the same time the water inlet valve is activated, the slide shutter is set to the middle spray arm position. The circulation pump with switched auxiliary winding is then operated.
G1000 / G2000 Dishwashers Technical Information Function Reset Language setting Programming Display Select Reset. To reset all parameters to the standard setting, press the OK button. Press the back button to return to the main menu. Select Language. Make the desired selection and confirm with the OK button. The display shows Reset factory default settings? Time of day setting Select Time of day, then one of the sub-menus and confirm with the OK button.
G1000 / G2000 Dishwashers Technical Information Function Programming Temperature setting Display Select Temperature. Make the The options °C and °F are available desired selection and confirm with the OK button. Buzzer Select Buzzer. Make the The display shows the options Off, activation / desired selection and confirm Normal and Loud deactivation and with the OK button. volume setting Audible Select Keypad tone.
G1000 / G2000 Dishwashers Technical Information Function Programming Water-Plus quantity Select Water plus. Make the normal / increased desired selection and confirm with the OK button Sensor softener Select Water hardness. Make activation / the desired selection and deactivation, water confirm with the OK button hardness manual setting Program running Select Shorten the program. time reduction Make the desired selection and (from software confirm with the OK button. version ID no.
G1000 / G2000 Dishwashers Technical Information 6.5.2.2 G2670 – Service Mode Initial requirements 1. Open the door. 2. Switch off the machine. Accessing Press and hold the C (Clear) button or touchpad. Switch on the machine. Release the C (Clear) button or touchpad. Immediately press and release the C (Clear) button or touchpad 3 times, at the 3rd time hold for at least 4 seconds.
G1000 / G2000 Dishwashers Technical Information Function Programming ID no. check Display Select ID Number. To return to The display shows version ID the main menu, press the OK no. for the selection-display button or touchpad. module (BAE) *1 and controlpower module (SLT) *2 Fault memory Select Fault memory. To return The display shows saved fault display to the main menu, press the OK messages. If several faults button or touchpad. have been registered, they will be indicated one after the other.
G1000 / G2000 Dishwashers Technical Information 6.5.2.3 G2670 Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: V01. R1, Y2, M6, …, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Warning! The circulation pump must not run for more than 30 sec. without water.
G1000 / G2000 Dishwashers Technical Information Starting with software version ID 984 the reactivation component test operates as follows: At the start of the mini-program the drain pump M8, water inlet valve Y2 and EGS valve Y5 are activated at the same time. M8 pumps water for 30 sec. and is primed with pulsed priming (2 sec. on/2 sec. off). Y2 and Y5 are switched off when 250 ml has been reached or 60 sec. has elapsed. The reactivation valve Y38 is then activated for 150 sec.
G1000 / G2000 Dishwashers Technical Information V17. 5N1, M6, wash sequence with bottom spray arm sensor (mini program): This starts with 30 sec. drainage, which begins with pulsed priming (2 sec. on / 2 sec. off). The water inlet valve is then activated (on models with and without slide shutter) until 5.4 l has been taken in. At the same time the water inlet valve is activated, the slide shutter is set to the middle spray arm position.
G1000 / G2000 Dishwashers Technical Information Function Programming Reset Select Reset. To reset all parameters to the standard setting, press the OK touchpad. Press the back button to return to the main menu. Language setting Select Language. Make the desired selection and confirm with the OK touchpad. Display The display shows Reset factory default settings? The display shows the available options. A language must be selected to return to the main menu.
G1000 / G2000 Dishwashers Technical Information Function Programming Saving extras Display Select Save extras. Make the desired This function is activated as selection and confirm with the OK standard. This is indicated in touchpad. the display by On. If the function is not desired, select Off. System lock Select System lock. Make the desired This function is deactivated activation selection and confirm with the OK as standard. This is indicated touchpad. in the display by Off.
G1000 / G2000 Dishwashers Technical Information Function Programming Resetting Select Factory default. If all standard settings parameters that can be modified by the customer (extras and settings) should be reset to the standard settings, press the OK touchpad. Otherwise, press the Back touchpad to go back one level. Wash/Final rinse Select Temperatures then temperature select the desired sub-menu. modification (from software version ID no. 984).
G1000 / G2000 Dishwashers Technical Information *1 If Permitted is selected, locking during operation is possible. However, locking can only be carried out after a program has been started, see the appropriate operating instructions. *2 If the electronic unit is replaced during service work, it must be programmed as follows: First set the country variant and model variant, then switch off the unit, repeat the accessing procedure and set the machine height.
G1000 / G2000 Dishwashers Technical Information 6.6.2 G2830 – Service Mode Initial requirements 1. Close the door. 2. Switch off the machine. Accessing 1. Press and hold the C (Clear) button or touchpad. 2. Switch on the machine. 3. Release the C (Clear) button or touchpad. 4. Immediately press and release the C (Clear) button or touchpad 3 times, at the 3rd time hold for at least 4 seconds.
G1000 / G2000 Dishwashers Technical Information Function Programming ID no. check Display Select ID Number. To return to The display shows version ID the main menu, press the OK no. for the selection-display touchpad. module (BAE) *1 and controlpower module (SLT) *2 Fault memory Select Fault memory. To return The display shows saved fault display to the main menu, press the OK messages. If several faults touchpad. have been registered, they will be indicated one after the other.
G1000 / G2000 Dishwashers Technical Information 6.6.3 G2830 Component Test After selecting the service mode and successfully accessing the component test program, individual electrical components can be activated via the program button (Start/Stop for Integrated models). During this procedure, certain components can only be activated via special mini-programs. Test sequence and background information: V01. R1, Y2, M6, …, wash sequence with heating (mini-program): This starts with 30 sec.
G1000 / G2000 Dishwashers Technical Information V06. M6, circulation pump switched winding relay: The circulation pump with switched auxiliary winding is activated. With a controlled circulation pump, the activation is at the maximum speed for controlled operation. The circulation pump is activated for 30 sec., but the auxiliary winding relay is only activated during the first 15 sec. Warning! The circulation pump must not run for more than 30 sec. without water.
G1000 / G2000 Dishwashers Technical Information Starting with software version ID 984 the reactivation component test operates as follows: At the start of the mini-program the drain pump M8, water inlet valve Y2 and EGS valve Y5 are activated at the same time. M8 pumps water for 30 sec. and is primed with pulsed priming (2 sec. on/2 sec. off). Y2 and Y5 are switched off when 250 ml has been reached or 60 sec. has elapsed. The reactivation valve Y38 is then activated for 150 sec.
G1000 / G2000 Dishwashers Technical Information (miniprogram): This starts with 30 sec. drainage, which begins with pulsed priming (2 sec. on / 2 sec. off). The water inlet valve is then activated (on models with and without slide shutter) until 5.4 l has been taken in. At the same time the water inlet valve is activated, the slide shutter is set to the middle spray arm position. The circulation pump with switched auxiliary winding is then operated. After 2 sec.
G1000 / G2000 Dishwashers Technical Information 6.
G1000 / G2000 Dishwashers Technical Information 6.8 Fault Repair Summary 6.8.1 No Power - Main Switch Is On 1. Check for 120 VAC from wall outlet. If hard wired check for voltage at terminal X3/1. If no voltage is present, check: a. Circuit Breaker Panel or “Fuse Box. b. If hard wired check for proper connection at terminal X3/1 2. Check for power to the electronic unit. a. If power is present, go to step 3. b. If no power is present, check wire continuity between electronic board and terminal X3/1. 3.
G1000 / G2000 Dishwashers Technical Information 6.8.4 Inlet / Drain LED Flashes and Lights up Alternately (Fully Integrated) On-site water supply valve closed. a. Open water supply valve. 1. Check Filter in WPS (WaterProof System) for blockage. a. Disconnect the dishwasher from the power supply. b. Close the water supply valve. c. Unscrew the WaterProof System from the water supply valve. d. Remover the washer from the threaded union. e. Remove the filter with needle nose pliers. f.
G1000 / G2000 Dishwashers Technical Information 6.8.7 Door does not close correctly 1. Incorrectly fitted Stopper at end of Top Basket Guide. a. Remove the Stopper and fit it correctly. 2. Door Seal incorrectly fitted and protrudes forward. a. Remove the Door Seal and fit it correctly (5.3.1). 3. Damaged Door Hinges a. Inspect and replace Hinges as necessary (5.2.5). 4. Locking latch is in the wrong position (Integrated models) a. Press door lock release. 5.
G1000 / G2000 Dishwashers Technical Information 6.8.9 Noises during drying cycle After the fan is switched on, there may be noises during the drying cycle. 1. Fan impeller not firmly mounted. a. Replace the fan (5.3.7). 6.8.10 Foreign object in drain system The drain pump or the non-return valve is blocked by a foreign object. 1. Insure the ring to the filter trap is properly fitted with the microfine filter housing, Mat No. 5672961 (refer to Fig. 6-2) Figure 6-2: Microfine filter trap.
G1000 / G2000 Dishwashers Technical Information Note For remedies to clear blockage see Fault code F11 “Drainage fault”, 6.8.13. 6.8.11 Poor Drying Results 1. Incorrect Dispenser setting. a. Adjust setting as necessary. 2. Rinse Aid Dispenser Flap not properly closed. The Rinse Aid Container filed with water during program operation. a. Flush the Dispenser, refill with new Rinse Aid. b. Replace Dispenser Assembly as necessary (5.2.6). 3. Rinse Aid not being dispensed/released. a.
G1000 / G2000 Dishwashers Technical Information 5. Heating element defective (F25). a. Replace the heating element 6. Heating relay defective (F25). a. Check the heating relay solenoid voltage (12 VDC) from the electronic unit. b. If no voltage is present, replace the electronic unit. c. Check the heating relay solenoid. Replace if necessary. 7. Excess quantity of detergent or rinse aid dispensed. Excess foam has developed (F25). a. Check the dispensed quantities of detergent and rinse aid.
G1000 / G2000 Dishwashers Technical Information 6.8.13 Water Present In Appliance And Is Not Being Drained Off 1. Drain Blocked (F11) Figure 6-3: Circuit test path for F11. After each drain pump step, the circulation pump operates for 2 sec. and the heater pressure switch checks the water level. If it is too high (Large quantity of residual water remaining in cabinet), the drainage time is extended.
G1000 / G2000 Dishwashers Technical Information 5. With the non-return valve removed, check the drain pump for proper operation by performing the following steps: a. Check the Drain pump Impeller blades for proper rotation. If stuck, look for Foreign objects blocking Impeller blades and remove. If Impeller blades are jammed and no foreign objects are located, proceed to next step. b. Remove the lower service door panel. c. Operate the dishwasher in a draining step. d. Check for power at the Drain pump.
G1000 / G2000 Dishwashers Technical Information 5. Check the Flow meter B3/4 for too few pulses (F13), no pulses (F12) or sluggish movement (F19) by performing the following steps: a. Remove the left side panel (5.1.1). b. Check that the plate with the reed switch on the flow meter is seated correctly. c. Check that the reed switch connection plug is seated correctly.
G1000 / G2000 Dishwashers Technical Information Test routine: Figure 6-5: F19 – Test routine. • Item a: Test time for one liter • If the test routine is successfully completed, water intake time will be extended • If the test routine is not successfully completed, a Fault code F19 is registered. Figure 6-5: F19 – Test routine. Refer to Fig. 6-5 for following test routine: a. As a first step, the water intake valve Y2 is activated, to let an additional 2 liters into the appliance.
G1000 / G2000 Dishwashers Technical Information e. If however the heater pressure switch B1/13 switches, the wash program is interrupted immediately, the drain pump runs, and Fault F19 is registered. 6.8.15 Wash Program Is Interrupted And Drain Pump Is Operated If an F18 fault is displayed The water inlet valve is open when it should not be (signal to open it has not been given by the electronic module). Water then flows into the appliance and unexpected pulses from the flow meter B3/4 are detected. 1.
G1000 / G2000 Dishwashers Technical Information d. Check if circulation pump is defective by performing the following steps: 1. Open the dishwasher door and insert your Miele bypass tool into the latching mechanism. 2. Turn on the dishwasher and select a wash program. 3. After the 30 sec. draining step, pay attention to the lower spray arm. As water enters the cabinet the circulation pump should be operating, increasing the water flow pressure.
G1000 / G2000 Dishwashers Technical Information If An F24 fault is displayed 18 sec. after starting the drain sequence the electronic board will perform an operational test on the heater relay. The circulation pump is not operating and no power is applied to the heater relay coil. If 120 VAC is registered at ST5 on the electronic board, then an F24 is logged in memory (see Fig. 6-6). Figure 6-6: Circuit test path for F24. 1. Check the heater relay contacts to see if they have been fused together.
G1000 / G2000 Dishwashers Technical Information If a F40 fault is displayed The electronic unit has a fault that cannot be repaired by the Service Dept. (e.g. hardware fault) 1. Replace the electronic unit (5.5.3). If a F42 fault is displayed A check ID carried out to ensure that the power frequency is within certain valid ranges (50 ± 5 Hz or 60 ± 5 Hz). This fault is registered when it cannot clearly be established which valid range is applicable. 1.
G1000 / G2000 Dishwashers Technical Information Figure 6-8: Circuit test path for F-51 (testing state) 1. Check the Heater relay for an open contact. If the relay is open during the testing state, Fig. 6-8. Then perform the following checks: a. Check to insure all plug connections are clean and secure. b. Check the connection wires for continuity. • If the Heater relay still shows an open contact, replace the Heater relay. 2. Insure the Heater pressure switch is in position 21/22 and 11/12.
G1000 / G2000 Dishwashers Technical Information If a F69 is displayed (circulation pump blocked) With the circulation pump operating, the pump pressure level switch contacts are checked. For this the heating relay must have been activated and both electronic unit inputs must be potential free. 1. Check for proper operation of the heater relay, see F25 Heating relay defective. 2. Check for proper operation of the heater pressure switch, see F14 Water intake fault: Heater pressure switch. 3.
G1000 / G2000 Dishwashers Technical Information Case 2: If the fault is registered later, the fault will be indicated in the display or via LEDs at the end of the program. The buzzer is then activated for 2 min. 1. The cause may lie with the position switch B3/12, which may have an intermittent contact. Check for dirty contacts clean or replace drive as necessary. 2. Check for pulses during operation at ST14 on the electronic board using a multimeter set for low voltage DC.
G1000 / G2000 Dishwashers Technical Information a. If pluses are present, the electronic board needs to be replaced. b. If pluses are not present, first check wire connections for an open or short circuit. Replace the slide shutter drive if necessary. 3. If the slide shutter gearing or the drive (synchronous motor) is defective. Replace the drive. Circulation pump speed too low fault is registered (F67). The check is carried out 10 sec. after the circulation pump has started. 1.
