Operating instructions Steam ironing system To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety.
Contents Caring for the environment .............................................................................. 2 Warning and Safety instructions ..................................................................... 6 Guide to the appliance ...................................................................................... 14 Transporting....................................................................................................... 17 Assembly...............................................
Contents Active ironing board ............................................................................................ Suction function ............................................................................................. Inflation function............................................................................................. Automatic switch on/off ................................................................................. Memory function ............................................
Contents Care products...................................................................................................... 65 Descaling tablets for the steam ironing system ............................................. 65 Problem solving guide ...................................................................................... 66 Troubleshooting................................................................................................... 67 Display messages .........................................
Warning and Safety instructions This steam ironing system complies with current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the steam ironing system, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance. Keep these instructions in a safe place and pass them on to any future owner.
Warning and Safety instructions Safety with children Children under the age of eight must be kept away from the steam ironing system unless they are supervised. Children older than eight may only use the steam ironing system unsupervised if they have been shown how to use it in a safe way, and recognise and understand the consequences of incorrect operation. Children must not be allowed to clean or maintain the steam ironing system unsupervised.
Warning and Safety instructions Technical safety Before setting up the steam ironing system, inspect it visually for any external damage. Never use a damaged steam ironing system. A damaged steam ironing system can be dangerous! Check the iron of the steam ironing system for damage. Do not use the iron if it has been dropped, if there is any visible damage or if it is leaking.
Warning and Safety instructions The electrical safety of this steam ironing system can only be guaranteed when correctly earthed. It is essential that this standard safety requirement is met. If in any doubt, please have the wiring system of the building tested by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate earthing system (e.g. electric shock).
Warning and Safety instructions The steam ironing system must be isolated from the electricity supply during installation, maintenance and repair work. The steam ironing system is only considered disconnected from the power supply if: - the power plug of the steam ironing system is unplugged, or - the mains circuit breaker is switched off, or - the mains screw-out fuse is removed (in countries where this is applicable).
Warning and Safety instructions Correct application Risk of burning due to hot components and steam. The soleplate and the areas surrounding it on the iron and the Steamer nozzles are very hot. Escaping steam can cause severe burns. Avoid direct contact with escaping steam, the soleplate and the Steamer nozzles. Never direct the soleplate and Steamer at other people, animals or electrical appliances of any kind.
Warning and Safety instructions Do not use solely demineralised water (e.g. distilled, battery water) to fill the water container. This could cause the steam ironing system to malfunction. Always place the iron with its soleplate horizontally on the resting surface of the steam ironing system. Ensure the steam function is switched off and the soleplate does not protrude over the edges. Do not place the iron anywhere else as this presents a fire hazard.
Warning and Safety instructions Do not use the residual water drawer to store accessories or similar items. The residual water drawer should be used only to collect residual water. Do not insert any objects into the apertures on the steam ironing system. If an aperture is blocked, do not use the system. Do not hang items of laundry on the folded steam ironing system. This may cause the steam ironing system to tip over due to the effect of leverage. Avoid ironing across hard or sharp-edged items.
Guide to the appliance a Ironing board i Ironing board X-frame b Iron with steam hose j Iron resting surface c Steam hose holder k Mains connection cable d Handle l Bottom storage compartment For the mains connection cable, the Steamer* and the non-stick soleplate e Water container f Tower g Residual water drawer h Top storage compartment For the iron and the steam hose holder m Rollers n Release handle For assembling the steam ironing system * Supplied as standard with steam ironing system B 484
Guide to the appliance Tower a Rotary dial for height adjustment and folding the appliance away Tower (top view) with open storage compartment (top) d Steam hose holders b Iron resting area e Control field c Steam connection f Iron with steam hose 15
Guide to the appliance Control panel on tower h On/Off button Switches the steam ironing system on or off. i Display Displays messages and instructions for the user. j Arrow button Lights up if additional options are offered or if the display text exceeds the specified length of a line. Scrolls down the list to the next option or decreases a value. k Arrow button Lights up if additional options are offered or if the display text exceeds the specified length of a line.
Transporting Danger of injury and damage to the appliance due to released ironing board. The ironing board lock may become dislodged if the steam ironing system is transported or lifted while it is assembled. Only ever transport the steam ironing system while it is folded up. The steam ironing system is fitted with 2 rollers. This allows the steam ironing system to be pulled across an even surface when folded up.
*INSTALLATION* Assembly Take the steam ironing system to its installation site. Use one hand to pull the release mechanism upwards. This releases the locking mechanism of the ironing board and the X-frame folds down. Use both hands to pull the ironing board upwards into a horizontal position until it audibly clicks into place on both sides of the tower. click! click! Ensure the ironing board has locked into place on both sides of the tower.
*INSTALLATION* Assembly Adjusting the height The steam ironing system can be adjusted to suit your personal preference. The maximum working height is around 102 cm. When adjusting the height, ensure the mains connection cable does not become trapped in the mechanism. The steam ironing system is now assembled. This is its lowest working position of approx. 83 cm high. Turn one of the rotary controls on the side of the tower handle as far as it will go in the direction.
*INSTALLATION* Assembly At the same time, pull the handle upwards with the other hand or press the handle down. Do not push down on the ironing board while adjusting the height. Always use the handle on the tower to adjust the height. When you have reached your desired working height, release the rotary control. The rotary control will spring back into the centre position. The ironing board remains in this position by itself.
*INSTALLATION* Connection Insert the mains plug into the socket. The steam ironing system is designed for connection to a properly installed earthed socket for AC 220-240 V, 50-60 Hz. Guide the power cable through the groove in the cover. Close the (bottom) storage compartment. Open the (lower) storage compartment by swinging the lid downwards. When closing the compartment, ensure the power cable does not become trapped between the cover and the housing or between the wheels and the tower.
*INSTALLATION* Connection Removing the iron and the steam hose holder The steam ironing system is suitable for right- or left-handed people. The operation is optimised for both sides. Connecting the steam hose Lift the lid of the steam connection. Open the lid of the top storage compartment on the tower. Take out the iron. Close the storage compartment lid. Pull back the slider on the steam hose plug. Insert the plug into the steam connection.
*INSTALLATION* Connection Danger of the iron tipping over if it is placed upright on its edge. An iron placed upright can easily tip over or fall to the floor. Always place the iron onto the resting surface with its soleplate down. Danger of burning on the resting Guide the steam hose on the rubber ring into the steam hose holder. Ensure the steam hose fits tightly and is not twisted.
Before using for the first time Before using the steam ironing system for the first time, remove all packaging (e.g. the protective film from the tower). Using the test strips Determining water hardness In order for the steam ironing system to function properly and to display a message prompting you to descale it at the correct time, it is important to adjust the steam ironing system to the hardness of your local water supply.
Before using for the first time Before using for the first time The following steps must be carried out before using the appliance for the first time: Language selection deutsch Switch on the steam ironing system Use the or arrow buttons to select your preferred language. Press the button on the control panel on the tower. Willkommen The Welcome screen appears for a few seconds in the display.
Before using for the first time Setting the water hardness Level 7 Set water hardness... Before the water hardness can be set, the display message Set water hardness... must be acknowledged by pressing the OK button. The steam ironing system gives you the option to set the water hardness to one of 10 settings. Use the following table to determine the water hardness level that must be set for your steam ironing system: °dH mmol/l °f Setting 1-4 0.2 - 0.7 2-7 Level 1 5-7 0.9 - 1.
Before using for the first time The steam ironing system is now ready for use This completes the settings for using the appliance for the first time. The message Initial set-up complete will appear in the display. Confirm this message by pressing the OK button. The steam ironing system will normally run a rinse programme automatically after it has been set up for use. The steam ironing system can then be switched off or you can continue using it.
Switching on Switching on the steam ironing system Press the button on the control field of the tower to switch on the steam ironing system. The button lights up and the welcome screen appears for several seconds in the display. If the iron was not connected to the steam connection before switching it on, the message Attach hose appears on the display. In this case, the steam hose must be attached to the steam connection (see “Connection”).
Switching on Filling the water container Filling the water container If the water container is empty or not installed in the tower, the message Fill water cont. will appear in the display. Removing the water container Open the screw cap at the rear of the water container by turning the cap anti-clockwise. Remove the screw cap. Hold the water container by its handle. Pull the handle downwards. The water container is released from the retainer. Pull the water container upwards and out.
Switching on Steam operation Water quality Use only fresh tap water. Ready for use After inserting the water container, wait until the steam ironing system is ready to use steam. This is indicated by the Ready for use message in the display. If the water container is refilled during the ironing process, the steam generator may have to reheat. Tip: If you fill the water container as soon as the Fill water cont. message is displayed and the container is inserted into the tower there is no delay.
Switching on Selecting the ironing temperature ➨ Use the temperature selector on the iron to set the ironing temperature. With temperature level the soleplate temperature is too low for ironing with steam. If you use this temperature level, do not use the steam button. If you do, water will escape from the steam jets. Tip: Sort your laundry according to the heat sensitivity of the fabric. This allows you to iron faster: First, iron your laundry that is made of heat-sensitive fabric (e.g.
Switching on Care label (on the garment) Ironing with steam for best results Ironing without steam (Material / Temperature setting) (Material / Temperature setting) Low temperature With non-stick soleplate (see “Ironing with the non-stick soleplate”) Minimum iron, synthetics, appliqués, prints, flocking, etc.
Switching on CoolDown function Iron switched off The heating of the iron switches off automatically if the iron is not moved for longer than 3 minutes. The message Iron switched off appears in the display to indicate that the heating has switched off. After a certain time, steam is no longer available. The message Release stm. button appears in the display when the steam button is locked. In this case, unlock the steam button by pushing the slider on the iron forwards (see “Ironing”).
Ironing Iron Depending on the model, your steam ironing system has one of the following irons: Steam ironing system B 4826 / B 4847: Steam ironing system B 4312: a Steam button b Slider for constant steam provision c Power level button a Steam button b Slider for constant steam provision c Suction function button d Inflation function button 34 d Inflation/suction button Irons supplied with previous Miele steam ironing systems (B 1xxx/B 2xxx) cannot be used with this appliance.
Ironing Ironing with steam The steam ironing system is ready for use when Ready for use appears in the display. The burst of steam is controlled by the button on the iron. When the button is pressed, the fan on the underside of the ironing board starts automatically. When the button is released, the fan will also stop after a brief run-on time. When using the steam function for a long time, make sure the room is well ventilated, as high air humidity can develop.
Ironing Ironing without steam Attaching the non-stick soleplate Remove the water container from the steam ironing system if you want to iron without steam. Place the tip of the iron inside the non-stick soleplate. The steam generator will not heat up and saves you energy. Ironing with the non-stick soleplate A non-stick soleplate has been included with the accessories which can simply be clipped onto the iron. The non-stick soleplate allows appliqués, printed or flocked textiles, etc.
Ironing Removing the non-stick soleplate Hold the iron by the handle. Risk of burning or scalding due to hot iron and non-stick soleplate. The non-stick soleplate is still very hot after ironing. Avoid direct contact. Only touch the tab of the non-stick soleplate. Active ironing board The steam ironing system uses a fan that sucks away the steam or uses the inflation function to inflate the ironing board for optimum positioning while ironing garments.
Ironing Memory function Fan control for the B 4826 / B 4847: The memory function saves the fan direction and the power setting used last with your steam ironing system. When you use the appliance the next time, you do not need to set it again. Heated ironing surface When the iron is connected and the steam ironing system is switched on, the surface of the ironing board will heat up automatically. This function reduces the formation of condensation on the ironing board.
Steamer The B 4847 steam ironing system is equipped with a steamer in addition to the iron. The steamer is available as an optional accessory for the B 4312 and B 4826 steam ironing systems. Disconnecting the iron from the steam connection Risk of burning or scalding due to the hot soleplate. The iron soleplate is still very hot after use. Avoid direct contact. Place the iron on its resting surface and let it cool down completely before you store it away. Do not pull on the steam hose.
Steamer Attaching the Steamer to the steam connection You can at any time plug the iron into the steam connection as an alternative to the Steamer. You do not need to switch off the steam ironing system to do this. After switching between the iron and the Steamer, there is a short interval before the steam is ready. This ensures that sufficient steam is available. The Steamer is ready when the message Ready for use is shown in the display.
Steamer Using the steamer Danger of burning due to hot steam! Never direct the steam or the steam jets at people, animals or electrical appliances of any kind. Never point the steam at clothing while the clothes are being worn! The clothing will intensify burning of the skin. Using short bursts of steam Briefly press button . Then release the button. Using continuous steam Press button . Keep the button pressed in. Stopping the continuous steam function Release button .
Steamer Brush attachment The steamer is equipped with a brush attachment which can be clipped on. The brush attachment helps to raise the fibres. You can hold the steamer directly onto the fabric while the brush attachment is in place. Always try it first on an inconspicuous part of the fabric. Connecting the brush attachment Guide the brush attachment into the notches on the opposite side. Press the brush attachment against the steamer until the lugs snap into the notches.
Switching off the steam ironing system To switch off the steam ironing system, press the button. The light in the button goes out. The steam ironing system is now switched off. The last selected fan settings are saved and are available for the next time you switch on the appliance. Bottom storage compartment Remove the mains connection cable from the bottom storage compartment. Place the iron on the resting surface until it has cooled down.
Dismantling Setting the ironing board to its lowest working height To dismantle the steam ironing system, the ironing board must first be set to its lowest working height. Make sure you do not trap the mains connection cable in the mechanism. Ensure the residual water drawer is completely emptied, pushed in and locked in place. Keep holding the rotary control in the direction and, simultaneously, use the handle to push the ironing board down as far as possible.
Dismantling Folding the ironing board Turn one of the two rotary controls as far as it will go towards the position. Push the ironing board up by the tapered end until it is upright and locks into position on the tower. The ironing board is now unlocked. Release the rotary control. The rotary control will spring back into the centre position. Push the protruding end of the Xframe onto the ironing board until the frame locks into place.
Dismantling Disconnecting the steam hose. Do not pull on the steam hose! Hold the plug at the end of the steam hose. The plug may still be warm immediately after using the system. Storing the iron Risk of burning or scalding due to the hot soleplate. The iron soleplate is still very hot after ironing. Avoid direct contact. Allow the iron to cool down after use. Do not stow the iron away while it is still attached to the hose.
Dismantling Emptying the water container Empty the water container if the steam ironing system is not going to be used for a long period of time. Storing the steam ironing system Take the steam ironing system to its storage place. Remove the water container (see “Filling the water container”). Make sure the water container is completely emptied. Do not store the steam ironing system in a room where temperatures below freezing may occur.
Cleaning and care Automatic rinsing The automatic rinse function clears the steam generator of mineral deposits from the evaporated water. After approx. 3 litres of water have been passed through the system, the rinse process will start automatically the next time the steam ironing system is switched on. The rinsing process takes several minutes. During the process, some steam escapes from the residual water drawer and splashing noises can also be heard.
Cleaning and care The residual water drawer is dishwasher-safe or can be washed by hand using warm water and a little washing-up liquid. Make sure the metal discs (contacts) at the top of the residual water drawer are clean and dry. These metal discs send a signal to the steam ironing system when the residual water drawer is full or if it is inserted into the tower. The discs will not function correctly if they are dirty or damp.
Cleaning and care Descaling warning Descale soon will appear in the display the next time you switch the steam ironing system on if there are only about 2 hours of ironing available before the system needs descaling. You can start the descaling process whilst the system is cold via the Settings menu (see “Starting the descaling process early”) or you can press the OK button to confirm the message in the display and continue ironing as normal.
Cleaning and care Starting the descaling process early Ready for use When the steam ironing system is switched on, press the button on the control panel. Descaling process The following display messages will guide you through the entire descaling process. Only proceed with the required action if you are prompted to do so by the appropriate message in the display. Detach hose The settings menu will be displayed. Use the arrow buttons to select individual settings.
Cleaning and care Fill water container to mark Add descaler Turn the screw cap at the back of the water container anti-clockwise and remove the cap. Hold the water container by its handle. Pull the handle downwards. The water container is released from the retainer. Pull the water container upwards and out. When removing the water container, you may notice some water dripping while the water container valves are closing.
Cleaning and care Fit water container Add descaler Press the OK button to display the next step. The message Fit water container will now appear in the display. Put the water container back into the tower. After about 10 minutes (the time it takes for the descaling tablet to dissolve), the descaling process begins automatically. Messages in the display will tell you when to empty the residual water drawer or when to fill the water container.
Cleaning and care Empty drawer This message may be displayed after inserting the water container with the descaling tablet. If you do not see this message, you can skip the following steps and continue as soon as you see Pre-rinse in the display. If the steam ironing system is still hot from the previous use, the cool down phase will start first. This may take up to 3 hours.
Cleaning and care Rinse water container and fill to the mark Remove the water container from the tower. As long as the water container is not inserted into the tower, the display will show the following message Fit water container. Open the screw cap. Empty drawer Remove the residual water drawer from the tower. The message Fit drawer will appear in the display. Empty the residual water drawer. Slide the residual water drawer back into the tower until it clicks into place.
Cleaning and care Descale After an activation time of approx. 1 hour, the descaling solution is drained from the steam generator into the residual water drawer. The steam generator is then rinsed with water. This rinse cycle takes approx. 5 minutes. During this time, the Rinsing (5 min) message is displayed. During the rinsing cycle, the message Rinsing is displayed.
Cleaning and care Rinsing the soleplate The iron must not be warm from previous use. Let the iron cool down for at least 60 minutes before rinsing the soleplate. Make sure that the non-stick soleplate has been removed from the iron. If the non-stick soleplate is still on the iron, remove it now (see “Removing the non-stick soleplate”). Fill the water container with fresh tap water (see “Filling the water container”).
Cleaning and care Now set the temperature selector on the iron to the highest temperature setting . Cleaning the housing Before cleaning the housing, switch off at the socket and withdraw the plug. Depending on the level of soiling, use a dry or moist soft cloth to wipe the housing. Do not use abrasive cleaning agents. Cleaning the soleplate of the iron The soleplate of the iron remains The indicator light on the temperature selector will light up yellow whilst the iron is heating up.
Cleaning and care To avoid damaging the surface, do not use the following for cleaning: - abrasive cleaning agents, (e.g. powder cleaners, cream cleaners, chrome polish, eraser blocks). - hard, abrasive brushes or sponges, (e.g. pot scourers), or sponges which have been previously used and still contain abrasive cleaning agents. - pointed objects. Cleaning or replacing the ironing board cover If the ironing board cover is soiled, you can wash and dry it.
Cleaning and care Wash and dry the ironing board cover according to the care label or replace the cover if it is damaged. Never use the steam ironing system without the ironing board cover in place! Put the dry or new cover onto the ironing board from the tower end first and draw it down towards the tapered end of the ironing board. Use the cord to pull the cover taut. Ensure the cover is secure.
Cleaning and care Removing the water filter cover Removing the sealing ring Use a cross-head screwdriver to remove the screw of the water filter cover. Use the hook on the water filter cover to pull the sealing ring up and out of the right-hand socket. Pull the water filter cover upwards. Please note that the top of sealing ring looks different to the bottom of it. The top has a smooth surface all round and the bottom has a narrow ridge around it.
Cleaning and care Pull out water filter Cleaning the water filter Push the round tool on the water filter cover onto the water filter from above. Detach the water filter from the round tool. The round tool will click into the water filter. Pull the water filter out of the socket. 62 Clean the water filter thoroughly under running water.
Cleaning and care Inserting the water filter Position the water filter with the small seal facing downwards. Press the water filter fully into the right-hand socket. Then replace the seal in the righthand socket. The side with the ridge must face downwards. Use a cross-head screwdriver to tighten the screw. Inserting the water container Replace the water container in the retainer in the tower. The steam ironing system is now ready for operation again.
Optional accessories Miele appliances are designed to achieve the best possible results and to provide uncompromising satisfaction for as long as possible. To achieve this, all factors must interact perfectly with one another. Therefore Miele offers a comprehensive range of accessories that harmonise with Miele appliances for optimum performance. The following items are just a few examples from our broad range of products, available to order from the Miele online shop (www.mieleshop.
Optional accessories Care products The Miele care product range has been developed specially to clean your appliance thoroughly and gently. Descaling tablets for the steam ironing system Miele descaling tablets guarantee the best cleaning result when descaling your Miele steam ironing system. One tablet is required for each descaling process.
Problem solving guide Most faults can be resolved by yourself. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a fault, and to correct it. Please note: Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Unauthorised or incorrect repairs can cause considerable danger to users.
Problem solving guide Troubleshooting Problem Cause and remedy The steam ironing sys- The steam ironing system does not have any power. tem cannot be switched Check that on. – the plug is inserted into the wall socket and that the socket is switched on. – the fuse in your fuse panel has not tripped. After an interruption to the power supply, the steam ironing system does not work any more.
Problem solving guide Problem Cause and remedy The ironing board cannot be set in the final position during assembly or dismantling. The ironing board became dislodged from the latching mechanism when the board was not in its lowest position. Danger of burning on the resting surface while it is hot. The resting surface for the iron remains hot after ironing. Switch off at the wall socket and unplug it.
Problem solving guide Problem Cause and remedy Use the button on the control panel to switch the steam ironing system on. The steam hose is not plugged in properly. Plug the steam hose into the steam connection on the tower again (see “Connection”). The iron has not been used for some time. Move the iron or activate the steam button . The steam button is locked. Unlock the button by pushing the slider on the iron forward.
Problem solving guide Problem Cause and remedy The ironing board is not Steam has not been used for a while. heated. Press the steam button . This will activate the ironing board's heating system. The steamer is attached to the steam connection on the tower. The ironing board does not heat up when the steamer is connected. The ironing board is not locked into place on both sides of the tower.
Problem solving guide Problem Cause and remedy The fan on the ironing board is not running. Steam was not used. The fan only runs when the steam function on the iron is activated. The appliance is not yet ready to produce steam. Wait until the message Ready for use is displayed to indicate that steam is ready. The water container is empty or not inserted. Refill the water container with fresh mains water and replace it in the tower. The steamer is connected.
Problem solving guide Problem Cause and remedy When using the steam button on the iron, drops of water or white deposits escape from the steam jets. The selected temperature level on the iron is too low. Set the temperature selector to at least (see “Selecting the ironing temperature”). The iron has not yet reached the selected temperature. Wait until the selected ironing temperature has been reached (see “Selecting the ironing temperature”).
Problem solving guide Display messages Message Drain valve closing Drain valve fault Switch off/on Memory fault Switch off/on Cause and remedy When the steam ironing system was switched on, the steam generator drain was open. The drain is closed automatically during this message. The descaling or rinsing processes have not been not carried out properly. Press the button to switch the steam ironing system off and then back on again.
Problem solving guide Message Cause and remedy There is a fault with the steam system. Press the button to switch the steam ironing system off and then back on again. Inlet fault, boiler Switch off/on After the cool-down phase, the steam ironing system will carry out an additional rinse function and attempt to correct the fault itself. The cool-down phase can take up to 3 hours. Remove the residual water drawer if you are prompted to do so by the appropriate message in the display.
Problem solving guide Message Cause and remedy There is a fault with the steam ironing system. Press the button to switch the steam ironing system off and then back on again. If the fault continues to be displayed, contact Miele Service. Boiler fault, cold Switch off/on Release stm. button Attach hose The iron has switched itself off because it has not been used for a period of time and the steam button has locked.
Problem solving guide Message Cause and remedy The residual water drawer has not been detected. Press the button to switch the steam ironing system off and then back on again. Drain valve fault Switch off/on After switching the steam ironing system off and back on, the residual water drawer has not been detected. Press the button to switch the steam ironing system off. Clean and dry the metal discs (contacts) on the residual water drawer.
Service Service Warranty In the case of a fault that you cannot rectify yourself, contact For information on the appliance warranty specific to your country please contact Miele. See back cover for address. - your Miele retailer or - Miele Service. The customer service telephone number can be found at the end of these operating instructions. Please note that telephone calls may be monitored and recorded for training purposes.
*INSTALLATION* Electrical connection UK Before you connect the steam ironing system, you must check the connection data (voltage and frequency) on the data plate and compare it with the data applicable to your local power supply. Compliance with this data is mandatory, otherwise there is a risk of damage to the steam ironing system. If in doubt, consult a suitably qualified electrician. You will find the necessary connection data on the data plate, which is located in the tower behind the water container.
*INSTALLATION* Electrical connection UK 79
Technical data Dimensions, folded (H x W x D) 1.280 × 470 × 370 mm Assembled dimensions (H x W x D) 970 × 470 × 1.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: info@miele.
FashionMaster en-GB M.-Nr.
