Operating instructions for condenser tumble dryer T 270 C To avoid the risk of accidents or damage to the machine it is essential to read these operating instructions before it is installed or used for the first time. G M.-Nr.
Contents Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Energy saving tips . . . . . . . . . . . . . . . . . . .
Contents Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Check and fault indicator lamps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 To change the interior drum lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 After sales service . . . . . . . . . . . . . . . . . . . . . .
Warning and Safety instructions To avoid the risk of accidents and damage to the machine please read these instructions carefully before using it for the first time. They contain important information on its safety, use and maintainence. Keep these operating instructions in a safe place and ensure that new users are familiar with the content. Pass them on to any future owner of the machine.
Warning and Safety instructions If the connection cable is faulty it must only be replaced by a Miele approved service technician to protect the user from danger. In the event of a fault or for cleaning purposes, the machine is only completely isolated from the electiricty supply when: – it is switched off at the wall socket and the plug is withdrawn, or – it is switched off at the mains, or – the mains fuse is withdrawn.
Warning and Safety instructions Always close the door after use. This way you will avoid the danger of: – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. Do not let anyone sit or lean on the door, as this can cause the machine to tip up. There is danger of fire with fabrics which: – contain a large proportion of rubber, foam rubber or rubber like materials. – have been treated with inflammable cleaning agents.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation! Rather than just throwing these materials away, please ensure they are offered for recycling.
Guide to the appliance Control panel / Features a Delay Start button The start of a programme can be delayed by up to 24 hours. b Start button Press the Start button to start a programme. The indicator lamp will flash to indicate that a programme can be started. It lights up constantly once the programme has started. c Display The display fulfills several functions. See next page for details.
Guide to the appliance Display The display shows a variety of functions: – it displays how long a programme has to run in hours and minutes; – with "Delay start" it displays the time remaining until the programme starts; – it displays programmable functions being selected and de-selected. Time left display for Cottons and Minimum Iron programmes Once a sensor programme has started the time left for a programme to run will be calculated by the machine.
Notes on laundry care Wash care labels Before drying check the drying symbol on the wash care label. Significance of symbols: q Dry at normal temperature r Dry at low temperature s Do not tumble dry If no symbol is featured, dry at your own risk applying the following principles: Cotton and minimum iron items should be dried using the appropriate programme for the degree of drying required. See programme chart.
Programme chart Programmes Fabric type Special notes Drying levels maximum load: 5 kg (1) COTTONS Multi-layered fabrics, which Do not dry jersey wear in the would not be thoroughly Extra dry programme dried using the "Normal +" tendency to shrink. programme. Single and multi-layered fabrics, e.g. mixed load of cotton fabrics (e.g. towelling, jerseywear).
Programme chart Programme Fabric type Special notes Drying levels maximum load: 2.5 kg (1) MINIMUM IRON Normal + Minimum iron items which are made of synthetic or blended fabrics (e.g. pullovers, dresses, trousers) which are not dried adequately in the "Normal" programme. Spin minimum iron fabrics for at least 30 seconds in the washing machine before drying. Normal (2) Minimum iron shirts, table cloths etc. made of blended fabrics (e.g. cotton/synthetics). Minimum iron shirts, table cloths etc.
Programme chart Programme Fabric type Special care programmes Woollens hand care Woollen fabrics maximum load: 2 kg (1) To refresh and fluff up woollen garments quickly. Remove garments immediately at the end of the programme. Do not repeat. Woollen fabrics are not dried completely by this programme. maximum load: 2.5 kg (1) Smoothing Cottons and linen fabrics. Minimum iron items made of cotton, blended fabrics or synthetics, e.g. cotton trousers, shirts.
How to dry correctly A Prepare the laundry ^ As far as possible, sort laundry for: - the type of fibre or weave, - the degree of dryness required, - similar size of items, - the moisture content after spinning. This will help towards achieving an even drying result. Fasten duvet covers etc. to prevent small items from being rolled up inside them. Do not overload the drum. Overloading can cause unnecessary wear and tear to the laundry and give a disappointing drying result.
How to dry correctly C Selecting a programme D Selecting additional options ^ Turn the programme selector to the programme required. ^ Additional options are selected before starting a programme by pressing the relevant buttons. It is not possible to activate additional options which are incompatible with the drying programme selected. The indicator light will go out when the option button is released. If an inappropriate combination of options is selected (e.g.
How to dry correctly Short For drying fabrics which can withstand high temperatures, e.g. pure linens and cottons. Do not use on minimum iron or delicate fabrics. E Delay start Once a programme has been selected, the start can be delayed by 30 minutes (30) up to 24 hours (24^). – Because the heater rating is increased clothes dry faster thus shortening drying times. Low temperature For drying delicate fabrics with the symbol r (e.g. acrylic garments) at a lower temperature.
How to dry correctly F Starting a programme ^ Press the Start button. The drying cycle begins. The drying stage reached is shown by the sequence indicator lamps on the right hand side of the control panel. At the end of the drying phase, a cooling down phase commences to cool the laundry down (the Cool air indicator lamp lights up). The drying level required has now been reached. G After drying The Anti-crease/Finish and the drying stage reached indicator lamps light up.
How to dry correctly Brief instructions F Start the programme These instructions are designed as a brief guide only. Please make sure that you also read the detailed instructions at the beginning of this section. ^ Press the Start button A Sort the laundry B Load the dryer and switch it on ^ Press the Door button to open the door. ^ Load the drum. ^ Close the door. ^ Switch the dryer on by pressing the l-On/0-Off button. C Select a programme ^ Turn the programme selector to the required programme.
How to dry correctly To change a programme Programmes cannot be changed after the start button has been pressed. If the programme selector is turned to a different programme after a programme has begun, this will not affect the programme. The Anti-crease / Finish indicator lamp will flash. The indicator lamp will go out when the selector is returned to its original position. After a programme has started, not all additional options can be switched on or off (see section "How to dry correctly").
Electronic system lock To de-activate the system lock The system lock prevents anyone from interfering with the dryer. If the system lock has been activated it is not possible to start a programme. The following steps (A,B,C...) must be carried out in the correct order. Please proceed step by step: To activate the system lock A Ensure that the door is closed and that the programme selector is turned to Finish. B Switch on the dryer with the I-On/O-Off button.
Cleaning and care Emptying the condensed water container The condensed water will be collected in the condensed water container unless the machine has been fitted with a drain hose (see installation). The condensed water container should be emptied after every drying cycle or as soon as the Empty out container indicator lamp comes on. The drying programme will be interrupted if the maximum level of the condensed water container is reached.
Cleaning and care Cleaning the fluff filters The fluff which is created by the drying process is collected by the fluff filters in the door and the door opening. Clean the filters after each drying programme. Cleaning them whilst dry ^ Open the door and pull the fluff filter out of the door as illustrated. ^ Remove any fluff from the hollow part of the door holder. A cleaning brush is available as an optional extra from your Miele dealer or the Miele Spare Parts Department.
Cleaning and care Cleaning them with water If there is a great deal of compacted fluff on any of the filters, they can be removed and cleaned under hot running water. ^ To remove the fluff filter from the door holder see previous page. ^ Place the filters back in the door opening (the left and right filters are identical) with the finger holders facing upwards. See illustration. Cleaning the tumble dryer Disconnect the machine from the mains electricity supply.
Cleaning and care Cleaning the condenser unit Detergent residue, hair and fine fluff from the dryer can get through the fluff filters and block the condenser unit. Dust from the room in which the dryer is installed can also get into the condenser unit and cause a blockage. Check the condenser unit at least twice a year. If the dryer is used frequently then clean the condenser unit after approx. 100 drying cycles.
Cleaning and care If you cannot see any fluff: ^ Replace the condenser unit (see following page). If you can see some fluff: ^ Clean the condenser unit as described below. Cleaning the condenser unit ^ When rinsing the condenser unit, make sure you position it as shown in the next two illustrations. ^ Pull the condenser unit out of its housing by the handle. Checking the condenser unit ^ Use a shower head or similar to rinse the unit out as shown. ^ Hold the condenser unit up to the light as shown.
Cleaning and care Replacing the condenser unit ^ With the handle facing upwards, push the condenser unit back into position in its housing. ^ Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the cover after cleaning, ensure that the rubber seal fits correctly into the groove. ^ Then flush the unit through from the front.
Problem solving guide With the help of the following notes minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repair work to electrical equipment should only be carried out by a suitably qualified person in accordance with local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work.
Problem solving guide Problem Possible cause Remedy There is a build up of fluff. Fluff is principally the result of friction when garments are being worn and washed. Machine drying hardly causes any fluff to form and has been established by research institutes to have no effect on the lifetime of fabric. The load consisted of different fabrics. Fluff is collected by the fluff filters and can be easily removed (see "Cleaning and Care"). – Finish drying using "Timed drying - Warm air".
Problem solving guide Problem Possible cause Remedy The drying process Important: Before attempting to remedy one of the goes on too long or following causes, switch the dryer off and switch on again even switches off. to start the programme again. Ventilation to and from the Open a door or window while the machine is in dryer may be insufficient (e.g because it is installed in operation for increased air a small room). This has flow. caused the temperature in the room to rise sharply.
Problem solving guide Problem Possible cause Remedy The inner cover of the condenser unit has not been locked properly and/or the condenser unit has not been positioned correctly. Water leaks from the Fluff has collected at the machine after the bottom of the condenser condenser unit has unit housing. been cleaned. The lighting switched off The interior drum lighting does not automatically. come on. – Ensure that the condenser unit is positioned correctly and lock the cover. – Check the rubber seals.
Problem solving guide Problem Possible cause Remedy The Clean out airways lamp comes on. The fluff filters may be blocked. The condenser unit may be blocked with fluff and detergent residues. Remove any fluff (see "Cleaning and care"). The programme stops and the Clean out airways lamp flashes. The Empty out container indicator lamp comes on. Please note that the condenser unit must be cleaned regularly (see "Cleaning and care"). The check lamp will go out when the door is opened.
Problem solving guide Problem Possible cause The programme has No obvious cause. been interrupted, the indicator lamp for Hand iron or Machine iron is flashing, and the buzzer sounds. Remedy – Switch the dryer off and then on again. – Then start the programme again. If the programme stops again and an indicator lamp flashes, there is a fault. Contact the Miele Service Department.
Problem solving guide To change the interior drum lamp ^ Open the door. Before changing the lamp, disconnect the machine from the mains power supply. ^ To close the flap push it upwards and press it on the left and right until you hear it click into position. The cover must be fixed securely, as otherwise moisture may seep in and cause a short circuit. You will find the interior lamp cover at the top of the drum aperture. ^ Insert the opener under the side edge of the cover as illustrated.
Problem solving guide After sales service Repairs Future updates (PC) In the event of any faults which you cannot remedy yourself, please contact The indicator or check lamp marked PC on the fascia panel is the interface used by the Miele service technicians during service work for testing purposes and for updating the machine's programme data. – Your Miele Dealer or – The nearest Miele Service Department (see back cover for address).
Installation Front view a Supply cable for electrical connection b Condensed water container c Control panel d Door e Service panel for condenser unit f Four height-adjustable screw feet g External drainage options (e.g. via wash basin, wash basin drain outlet, or gully).
Installation Installation site ,Make sure the dryer door can be opened without hindrance after installation. Transporting the machine to its installation site When moving the machine you can hold it by the lid where it protrudes to the rear of the dryer. To manoeuvre the dryer out of its packing case to its installation site you will also need to hold it by the front feet. Building under a continous worktop / in a row of kitchen units The dryer should not be installed next to a refrigerator or freezer.
Installation Aligning the machine Room in which the dryer is located Air taken in for use in the drying process will be warm when it is expelled from the rear of the dryer. This expelled air heats up the air in the room. It is therefore very important to ensure that the room is adequately ventilated, particularly if the dryer is located in a small room. Otherwise running times and energy consumption could be increased.
Installation External condensed water outlet From the back of the dryer at the bottom: When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the machine is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied. The drain hose (approx. 2 m long) is stored in the dryer.
Installation Connection to a sink drain outlet The drain hose can be connected directly to a sink drain outlet. If this nut has a flat disc sealing it you should take the disc out first. Important: if this nut has a washer or seal in it this must not be removed! ^ Attach the end of the hose to adapter 1. ^ Use a screwdriver to tighten hose clip 3 up close to the nut. If you no longer wish to use an external condensed water outlet ,Do not push the drain hose back into the dryer.
Electrical connection Electrical connection U.K. All electrical work should be carried out only by a suitably qualified and competent person, in strict accordance with national and local safety regulations. Ensure power is not supplied to the machine while installation work is being carried out. The machine is supplied with a mains cable with moulded plug for connection to a 230-240V mains supply. The voltage, rated load and fuse rating are given on the data plate.
Electrical connection If the colours of the wires in the mains lead of this machine do not correspond with the coloured markings identifying the terminals of your plug, proceed as follows: ^ The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol z or coloured green, or green and yellow. ^ The wire which is coloured blue must be connected to the terminal in the plug which is marked with the letter N or coloured black.
Consumption data Capacity Final spin speed (in a domestic washing machine) Electricity consumption Drying time incl. cooling down time kg rpm kWh Minutes Extra dry 5.0 Normal + 5.0 1200 1400 1600 1200 1400 1600 3.25 3.10 2.85 2.80 2.65 2.40 86 83 76 76 73 66 Normal (1) 5.0 800 (70 % residual moisture) 3.40 Normal 5.0 1200 1400 1600 2.65 2.55 2.25 89 73 70 63 Programme COTTONS (1) 5.0 800 (70 % residual moisture) Hand iron 5.0 Machine iron 5.
Technical data Height 85 cm (adjustable +0.7/- 0.7 cm) Height without lid 82 cm Width 59.5 cm Depth 58 cm Depth with door open Weight 106 cm 54 kg Drum volume Maximum capacity 100 litres 5 kg dry weight Capacity of condensed water container Length of connection cable approx. 3.5 litres 1.
Programmable functions for changing standard settings 45
Programmable functions Increased drying level The Sensitive System aims to dry using as little energy as possible. However, if you require the laundry to be drier, it is possible to reduce the final moisture level in the COTTONS and MINIMUM IRON programmes. The machine is delivered with this programmable function switched off.
Programmable functions Memory The additional options selected previously for specific programmes are stored in the machine’s memory. The machine is delivered with this programmable function deactivated. It can be activated if wished. Programming and storing in memory The programmable functions are activated to call up further features not shown on the control panel by using the additional option buttons in combination with the programme selector.
Alteration rights reserved/4703 M.-Nr. 05 993 050 / 01 This paper consists of cellulose which has been bleached without the use of chlorine.