User Manual

ManualsBrandsMidland Radio ManualsElectronicsVHF Transceiver

Table Of Contents

SERVICE MANUALS

Testing, alignment and service information are provided in the service

manual for this model. Service manuals for Titan™ radios are

available from Midland Radio Corporation at the address shown on

the back cover.

DO NOT transmit more than 50% of total radio use time (50% duty

cycle). Transmitting for more than 50% of the time can cause FCC

RF exposure compliance requirements to be exceeded. This radio is

transmitting whenever the TX icon is displayed on the LCD. Pressing

the PTT switch on the side of the microphone normally causes the

radio to transmit.



Note: The preceding information is provided to make you

aware of RF exposure and how to ensure that this radio is

operated within FCC RF exposure limits.

You, as the qualified end-user of this radio device must control the

exposure conditions of bystanders to ensure the minimum separation

distance, stated above for satisfying FCC RF exposure compliance, is

maintained between the antenna and nearby persons. Transmit only

when all person(s) are at least the minimum distance from the

properly installed, externally mounted antenna.

IMPORTANT SAFETY INFORMATION

CAUTIONS

The antenna connector must be snugly tightened to maintain

proper electrical connection and moisture resistance.

Equipment must be grounded according to Midland Radio

Corporation installation instructions for safe operation.

Equipment should be serviced only by a qualified technician.

Refer to radio service manual for additional information on

installation and safety precautions.

WARNING!

DO NOT allow the antenna to touch or come in very close

proximity with the eyes, face, or any exposed body parts while the

radio is transmitting

DO NOT operate the radio in explosive or flammable

atmospheres. The transmitted radio energy could trigger blasting

caps or cause an explosion.

DO NOT allow children to operate or play with this radio.



Note: The above warning list is not intended to include all

hazards that may be encountered when using this radio.

Summary of content (6 pages)

PAGE 1
SERVICE MANUALS Testing, alignment and service information are provided in the service manual for this model. Service manuals for Titan™ radios are available from Midland Radio Corporation at the address shown on the back cover. DO NOT transmit more than 50% of total radio use time (50% duty cycle). Transmitting for more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. This radio is transmitting whenever the TX icon is displayed on the LCD.
PAGE 2
CONTROLS AND INDICATORS POWER/VOLUME KNOB Press and hold for a few seconds for power on. Press and hold again for power off. Clockwise rotation increases volume of received messages. CHANNEL/MENU CONTROL KNOB Channel Function: Rotate to scroll through channels. Your radio can be programmed, by the radio technician to either stop at the highest and lowest channels, or for channel rollover.
PAGE 3
4. PRI monitor function is not available in this mode. If scan is stopped, Add/Delete of Group B channels is available in Add/Delete mode. MON 5. Other operation is the same as type “A” scan. TYPE “B’ ” SCAN MODE 1. Operation is the same as type “B” scan, except the SCAN button operation is the same as type “A” scan. 2. If scan is stopped, Add/Delete of Group B channels is available in Add/Delete mode. A/ D TYPE “PS” SCAN MODE 1. The “A” channels will be scanned in this mode. 2.
PAGE 4
NOTES: Squelch level setting can affect scan operation. If scanning SENDING A MESSAGE (TRANSMIT) appears slow it may be necessary to adjust the squelch to a higher level. The “OFF HOOK SCAN STOP” enable/disable is programmed by the radio technician prior to use of the radio. 1. Press MON to deactivate the Coded Squelch feature. If your transceiver is equipped with the Midland Switched Hang-Up Box, simply lift the hand microphone from the box, instead.
PAGE 5
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and MON A/D SCAN AUX 2. This device must accept any interference received, including interference that may cause undesired operation.
PAGE 6
70-2357 FCC RF EXPOSURE REQUIREMENTS The FCC has adopted a safety standard for human exposure to RF energy. Proper operation of this radio under normal conditions results in user exposure to RF energy below the Occupational Safety and Health Act and Federal Communication Commission limits.