Nokia Bluetooth Headset BH-806 5555555/1 Cyan Magenta Yellow Black
Cyan Magenta Yellow Black
Introduction About your headset With the Nokia Bluetooth Headset BH-806, you can handle calls hands-free, even when you are using two mobile devices at the same time. Note: The surface of this product does not contain nickel in the platings. The surface of this device contains stainless steel. Read this user guide carefully before using the product. Also, read the user guide for the device that you connect to the product. ENGLISH For more information, go to www.nokia.com/support.
Get started Keys and parts 1 Indicator light 2 Multifunction key 3 Earpiece 4 Microphone 5 Carrying clip 6 Charger connector Start using your headset The headset comes with different sized earpads. Select the earpad that fits the best and is the most comfortable for your ear. To change the earpad, pull the current earpad from the earpiece, and push the new earpad into place. ENGLISH 1. To switch the headset on, remove it from the carrying clip. If the headset doesn't switch on, charge the battery. 2.
light turns green when the battery is fully charged. 4. Disconnect the charger from the carrying clip, then from the wall outlet. The fully charged battery has power for up to 5 hours of talk time and up to 100 hours of standby time. If you keep the headset in the carrying clip, the standby time is up to 3 months. When the battery charge is low, the red indicator light flashes, and you hear a voice prompt every 5 minutes. If you have deactivated voice prompts, the headset beeps every 5 minutes.
Tip: Don't have the carrying clip with you? To switch the headset off, press and hold for 4 seconds. To switch the headset on, press . Pair and connect the headset to your mobile device Before using the headset, you must pair and connect it to a compatible device. 1. To switch the headset off, press and hold for 4 seconds. 2. Switch on the device to pair with. 3. If you have never paired the headset with a device, or you have cleared the device pairings, switch the headset on.
With some mobile devices, you may need to make the connection separately after pairing. Wear the headset Gently push the earpiece into your ear. Make calls Make and receive calls To make and receive calls using your headset, you need to connect it to your mobile device. Make a call — Make a call in the normal way. Answer a call — Remove the headset from the carrying clip. Tip: If the headset is not in the carrying clip, touch . ENGLISH When you're not using your headset, keep it in the carrying clip.
You can redial the last called number or use voice dialling, if your mobile device supports these features with the headset. Redial the last called number — When no call is in progress, press . Use voice dialling — When no call is in progress, press and hold for 2 seconds, and follow the instructions in the user guide of your mobile device. Change the volume Set the desired volume level on your connected mobile device.
Handle calls from two devices End an ongoing call, and answer a call on another device — Touch . Put an ongoing call on hold, and answer a call on another device — Touch and hold for 2 seconds. Switch between active and held calls — Touch and hold for 2 seconds. Settings Deactivate voice prompts Make sure the headset is switched on, and touch and hold for 9 seconds. You hear a voice prompt, and a yellow indicator light flashes once. ENGLISH End an ongoing call, and activate a held call — Touch .
Clear device pairings When you clear the device pairings, you need to select the language again. 1. To switch the headset off, press and hold for 4 seconds. 2. Press and hold for 9 seconds. The headset beeps twice, and the red and green indicator lights alternate. 3. When the headset switches on, follow the voice prompts. Pairing mode is activated. ENGLISH 1. To switch the headset off, press and hold for 4 seconds. 2. Press and hold for 9 seconds.
Product and safety information Compatible chargers This device is intended for use when supplied with power from the following chargers: AC-10, AC-6, DC-10, DC-6, DC-11, DC-11K, DT-600, and ENGLISH CA-146C. The exact charger model number may vary depending on the type of plug. The plug variant is identified by one of the following: E, X, AR, U, A, C, K, or B.
conditions: 1. This device may not cause harmful interference; and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Droits d'auteur et autres avis DÉCLARATION DE CONFORMITÉ NOKIA CORPORATION déclare par la présente que le produit BH-806 est conforme aux exigences essentielles et aux dispositions applicables de la Directive 1999/5/EC. Vous trouverez une copie de la déclaration de conformité à l'adresse www.nokia.com/phones/ declaration_of_conformity/. © 2010 Nokia. Tous droits réservés. Bluetooth est une marque déposée de Bluetooth SIG, Inc.
dans une installation donnée. Si cet appareil cause de l'interférence nuisible à la réception de la radio ou de la télévision, ce qui peut être déterminé en éteignant et en allumant l'appareil, essayez de corriger l'interférence au moyen des mesures suivantes : Réorientez ou déplacez l'antenne. Augmentez la distance entre l'appareil et le récepteur. Connectez l'appareil dans la prise d'un circuit différent de celui où est connecté le récepteur.