User's Guide

ManualsBrandsMicronet Union Technology ManualsComputers & AccessoriesAX1500 Wi-Fi 6 Router

Table Of Contents

页 1

4. Configure the Router

The device 1pc

Power adapter 1 pc

User guide 1pc

Ethernet cable 1pc

1. Product Overview

2. Indicator Led

3. Connect the Router

Green on

Red on

Flashing

Allow connection

No Internet connection

Please refer to this user guide to configure the router correctly.

Please make sure that the Ethernet cable is not loose and the

connection is correct

Please check if there is any network fault.

WPS or Mesh networking is

on processing

User Guide

AX1500 Wi-Fi 6 Router

If the above accessories are missing, please contact the

customer service in official website for replacement.

Packing list:

①Indicator light

②Reset (long press over 5 seconds)

③WPS Key(press within 5 seconds for WPS, 5 seconds above for

mesh)

④LAN port : connect to computer, etc.

⑤WAN port : connect to modem, broadband modem, etc.

⑥Power port ( DC IN )

Connect the Device

Wireless connection

The client-side connects to router Wi-Fi

The defaulted username

and password are on the

bottom label

Wired connection

Connect the PC and router via LAN1, LAN2 or LAN3 with cable

cable

switch on

cable

Use DSL or PON for Internet connection

modemn

Community broadband Internet access

telephone line or fiber

4.1 Open the mobile phone or computer browser, visit the http:// 192.

168.10.1 website, enter the router management interface.

4.2 Enter the default username and password on the label at the

bottom of the router.

4.3 After accessing the management interface, select the network-

mode-PPPOE, DHCP or Static IP to set according to the broadband

you are using.

(1) When selecting PPPOE, please enter the UserName and

Password provided by the network operator, and click Apply.

(2) When selecting DHCP, enter relevant information according to

the prompts on the page, click Apply.

(3) When you choose "Fixed IP" to access the Internet, enter

relevant information according to the prompts on the page and click

"Apply"

5. Password Setting

6. EasyMesh Configuration

In the router management interface of http:// 192.168.10.1, click

Quick Setup interface to customize the WLAN (2.4GHz) / WLAN

(5GHz) password. After setting the password, click Apply.

One-click Mesh function:

1.Complete the configuration of the Controller, ensure that the

Controller’s network is normal, and the green light is on.

2.When additional Agent is needed: take out the new device and

connect to the network, press the WPS button of the Controller and

the Agent at the same time (for more than 5 seconds) for networking.

3.Before networking, the indicator light of the Controller is on green

(the network is normal), and the Agent is on red (the network is

abnormal). In the process of networking, the indicator light of the

Controller is on green flashing and the Agent is on red flashing.

After the success of networking, the indicator light of the Controller

is on green, and the indicator light of the Agent turns to green from

red.

Mesh Setting

1. Setting the Controller: select WLAN –Easy Mesh in the router

management interface: fill Controller in Device Name; select

Controller in Role; Click the Apply button to save the Settings.

7. Frequently Asked Questions

9. FCC Warning Statement

10. After-sales Service Commitment

2. Setting the Agent, in the router management interface of Agent,

select WLAN -EasyMesh: fill Agent in Device Name; select Agent in

Role; Click the Apply button to save the Settings.

3. After the two devices complete the above steps, the EasyMesh

page will refresh and the Start PBC button will appear. Click Start

PBC for both devices, or press the WPS button shortly, automatic

mesh network can be triggered.

7.1. What to do if there is a problem when setting the router to surf

the Internet ?

①If you cannot find the router’s SSID on your mobile phone, please

make sure that the router is powered on, wait for a moment and wait

for the router to finish start-up, and then search again on your

mobile phone to connect.

②If the device cannot connect to the network, please ensure that the

network port connection of the router is not loose, no poor contact,

and no abnormal network cable.

7.2. How to restore the router to factory settings ?

①Power on the router and wait for a moment until the router finish

start-up. Press the RESET hole of the router with a needle for more

than 5 seconds. After the indicator light goes out, release it. After

the red light is turned on when the router restarts, the factory setting

restoration has been completed. After the factory settings are

restored, the router needs to be reconfigured.

7.3. What should be paid attention to during the setting of EasyMesh ?

①After the completion of EasyMesh networking, the Controller will

synchronize its SSID, password and channels of 2.4GHz and 5GHz

to the Agent.

②After modifying the SSID, password and channel on the Controller,

the Controller will synchronize these configurations to all Agents. If

th e above in formati on is modi fied on th e Agent, i t will no t

synchronize to other devices.

③After the power failure, the routers will resume the original

EasyMesh network by default, and there is no need to reset.

④If the EasyMesh network of the Controller is closed, the whole

network will be dissolved; If the EasyMesh network of the Agent is

turned off, the device is disconnected from the mesh network alone.

8. Security Issues

①Before using and operating the router, please read and observe

the following notes to ensure the stable performance of the router

and to avoid dangerous or illegal situations.

②Please use and store the router and its accessories within the

temperature range of 0℃~40℃. When the temperature is too high or

too low, it may cause equipment failure.

③In the process of using the router, ensure that the distance

between the human body and the antenna of the router is more than

20cm.

④Only use accessories approved by the router manufacturer and

compatible with this type of router. If other types of accessories are

used, it may violate the warranty of the router and the relevant

regulations of the country where the equipment is located, and may

lead to safety incidents.

⑤Power sockets shall be installed near the router and shall be

easily accessible.

⑥When the device is not in use, disconnect the power from the

router and unplug the power plug from the power socket.

⑦Do not dispose of the equipment and its accessories as ordinary

household waste.

FCC Radiation Exposure Statement:

The antennas used for this transmitter must be installed to provide a

separation distance of at least 20cm from all persons and must not

be co-located for operating in conjunction with any other antenna or

transmitter.

Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to

operate the equipment.

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

1.Reorient or relocate the receiving antenna.

2.Increase the separation between the equipment and receiver.

3.Connect the equipment into an outlet on a circuit different from

that to which the receiver

is connected.

4.Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is

subject to the following two conditions (1) this device may not cause

harmful interference. (2) this device must accept any interference

received, includ i n g i n t e rference th a t m a y ca u s e un d e s i r e d

operation.

① Implementation of the three guarantees regulations, one-year

warranty;

② The free warranty period of the product is one year, calculated

from the date of sale;

③Under the following circumstances, three guarantees are not

implemented, and paid maintenance is implemented:

a. Failure caused by man-made damage, improper operation or

irresistible natural disasters;

b. Failure caused by remodeling, disassembling and assembling the

product by yourself;

c. Exceeding the validity period.

Quick guide(说明书)

Technical requirements:(技术要求)

1. Material:70 g writing paper(材质：70g书写纸双面印刷)

2. Size:90*120mm(单页尺寸：90*120mm)

3.Fold way: organ fold(折叠方式：风琴折)

This page allows you setup the WLAN security,Turn on WEP or WPA by using Encry

access to your wireless network.

This page is used to conﬁgure the parameters for EasyMesh feature of your Access Point.

This page is used to conﬁgure the parameters for Ethernet WAN.

This page is used to conﬁgure the parameters for EasyMesh feature of your Access Point.

Ethernet WAN

WLAN Security Settings

EasyMesh Interface Setup

名称

日期

描述

2021-08-05

外置天线系列-说明书-海外版V1.0

技术要求：

1. Material:70 g writing paper(材质：70g书写纸双面印刷)

2. Size:90*120mm(单页尺寸：90*120mm)

3.Fold way: organ fold(折叠方式：风琴折)

4.公差：±0.05mm

包装设计

项目负责人

内/外贸

批准

权责人

内容

负责整体效果尺寸版式设计

负责稿件和内容评审

英文文案

蒋婷

彭志

外贸

时间

变更人

变更内容

补充项

深圳市微网力合信息技术有限公司

图纸编号

RT21F03801