Operating Manual pDDL2450 Pico 2.4GHz 1W Digital Data Link Module Revision 0.35, April 12, 2016 Microhard Systems Inc. www.microhardcorp.
Warranty Microhard Systems Inc. warrants that each product will be free of defects in material and workmanship for a period of one (1) year for its products. The warranty commences on the date the product is shipped by Microhard Systems Inc. Microhard Systems Inc.’s sole liability and responsibility under this warranty is to repair or replace any product which is returned to it by the Buyer and which Microhard Systems Inc. determines does not conform to the warranty.
pDDL2450 Regulatory Requirements - PLEASE READ THIS SECTION CAREFULLY WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 23 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
pDDL2450 Exigences Réglementaires WARNING: Pour satisfaire aux exigences de la FCC d'exposition RF pour la base et mobiles sur une distance de séparation de 23 cm ou plus doit être maintenue entre l'antenne de cet appareil et des personnes lors de fonctionnement du dispositif. Pour assurer la conformité des opérations au plus près que cette distance n'est pas recommandée. L'antenne utilisée pour ce transmetteur ne doit pas être colocalisés en conjonction avec toute autre antenne ou transmetteur.
Co-Location with Cellular Modems FCC: The maximum calculated MPE ratio for the EUT with 2 dBi dipole antenna is 0.238 (evaluated at 23 cm), this configuration can be co-located with other antennas provided the sum of the MPE ratios for all the other simultaneous transmitting antennas incorporated in a host device is < 1.0 - 0.238 < 0.762. The following co-location were evaluated for mobile configurations: Industry Canada: The maximum calculated MPE ratio for the EUT with 2 dBi dipole antenna is 0.
Contents Warranty ................................................................................................................................................................ ii Proprietary Rights .................................................................................................................................................. ii pDDL2450 Regulatory Requirements ...................................................................................................................
2. General 2.0 Product Overview The pDDL2450 is a high-performance embedded wireless data transceiver. Operating in the 2400 – 2483.5 MHz ISM band, this frequency-hopping spread-spectrum module is capable of providing reliable wireless data transfer between almost any type of equipment which uses an asynchronous serial interface. The small-size and superior RF performance of this module make it ideal for many applications.
TDMA (time division multiple access) support, allowing multi-slave access in point-to-point mode. roaming ability, allowing repeaters and slaves to resynchronize with a new master if the synchronization pulse from the original master is lost. While the typical application for the pDDL2450 is to provide a short- to mid-range wireless communications link between DTEs, it can be adapted to almost any situation where an asynchronous serial interface is used and data intercommunication is required. 2.
3. Installation 3.0 Overview The pDDL2450 complies with FCC part 15 at the modular level for operation in the license-free 2400-2483.5 MHz ISM band. This chapter provides guidelines for installing and deploying equipment which incorporates the pDDL2450 module. 3.
Figure 1 Gain Calculation The power level has been set to 30dBm (1W) on the transmitter, and the receiver sensitivity for the pDDL2450 is -108dBm. System gain would be calculated to be: 30 - 2 + 6 + 3 - 2 + 108 = 143 dB.
Once the equipment is deployed, you can verify the signal strength by entering into Command Mode and reading Register S123. This register provides the average signal strength in dBm. The minimum strength for communication is roughly -108dBm. For consistent reliable communication, you should try to deploy the equipment such that signal strength exceeds -95dBm. 3.2 Antennas and Cabling This section describes the recommended procedure for installing cabling and antennas for use with the pDDL2450 module. 3.2.
3.2.2 Installing External Cables, Antennas and Lightning Arrestors WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 23 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter.
WARNING: MAXIMUM EIRP FCC and IC Regulations allow up to 36dBm effective isotropically radiated power (EIRP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36 dBm with respect to the isotropic radiator. WARNING: The pDDL2450 can only be used with any antennas listed in Appendix A. WARNING: Be careful with dBi vs dBd gains on antenna specifications. Antenna manufactures may not clearly indicate the gain on the antenna if it is dBd or dBi.
Examples: FCC and Industry Canada Regulations allow up to 36dBm effective isotropically radiated power (EIRP). Therefore, the sum of the transmitted power (in dBm), the cabling loss and the antenna gain cannot exceed 36dBm with respect to the isotropic radiator.
A. Approved Antennas This radio transmitter (IC:3143A-16PDDL2450) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
