User's Manual

ManualsBrandsMicro Star International ManualsComputers & AccessoriesWireless 11g MiniPCI Card

Wireless 11g MiniPCI Card MP54G User’s Guide

Specifications>>> 1.3

Hardware Specifications

Compliant Standards

- IEEE 802.11g/b

Bus and Connector Types

- 32-bit 3.3V Type IIIA

- 124-pin Golden Finger

Security Mechanism

- Hardware-Base WEP Privacy

- Hardware-Base AES Privacy (driver update)

Operational Environment

- Operational Temperature: 0 ~ 55

- Humidity: 10 ~ 90% (Non-Condensing)

Weight and Dimension

- Weight:11.5g

- Dimension: 50.8 x 59.6 x 4.9mm

Radio Frequency Specifications

Raw Data Rates and Modulation Types

- IEEE802.11b (Auto-Fallback)

CCK: 11 and 5.5Mbps

DQPSK: 2Mbps

DBPSK: 1Mbps

- IEEE802.11g (Auto-Fallback)

OFDM: 54, 48, 36, 24, 18, 12, 9, 6Mbps

Communication Protocol

- DSSS (Direct Sequence Spread Spectrum) with

ACK

- Half-Duplex

Access Method

- Infrastructure Mode: Station-To-LAN Architecture

- Ad-Hoc Mode: Station-To-Station Architecture

Summary of content (9 pages)

PAGE 1
Wireless 11g MiniPCI Card MP54G User’s Guide >>> 1.3 Specifications Hardware Specifications Compliant Standards IEEE 802.11g/b Bus and Connector Types 32-bit 3.3V Type IIIA 124-pin Golden Finger Security Mechanism Hardware-Base WEP Privacy Hardware-Base AES Privacy (driver update) Operational Environment Operational Temperature: 0 ~ 55OC Humidity: 10 ~ 90% (Non-Condensing) Weight and Dimension Weight:11.5g Dimension: 50.8 x 59.6 x 4.
PAGE 2
Wireless 11g MiniPCI Card MP54G User’s Guide Frequency, Bandwidth, and Channels 2.4 ~ 2.
PAGE 3
Wireless 11g MiniPCI Card MP54G User’s Guide >>> 1.4 System Requirements Before installing the MP54G, your PC should meet the following: Desktop/notebook PC with an available MiniPCI slot. Windows® 98SE/ME/2000/XP operating system. Minimum 5M bytes free disk space for installing the driver and utilities. CD-ROM drive, double speed or higher. >>> 1.5 Package Contents Unpack the package and check all the items carefully.
PAGE 4
Wireless 11g MiniPCI Card MP54G User’s Guide >>> 1.6 Product View External antenna connectors (J1: Main, J2: Aux) Connect to external antennas for enhanced data transmission and reception. The external antennas are well designed on the desktop or notebook computers. NOTE: Please connect the J1(Main) connector if there is only one antenna to connect.
PAGE 5
Wireless 11g MiniPCI Card MP54G User’s Guide Hardware Installation The following diagrams provide you with a basic installation for the MP54G, including how to install and remove the MiniPCI card. The instruction below is suitable for most computers with MiniPCI slot. For more information about the MiniPCI module, please refer to your computer’s manual. >>> 2.1 Installing the MP54G 1. Locate the Mini PCI slot on the mainboard. 2. Place the MP54G over the MiniPCI slot (at an angle of 30 degrees).
PAGE 6
Wireless 11g MiniPCI Card MP54G User’s Guide >>> 2.2 Removing the MP54G 1. Locate the MiniPCI slot with MP54G installed. 2. Press the retaining clips outwards, and the card should bound upwards slightly after being released from the slot. 3. Remove the card from the MiniPCI slot carefully.
PAGE 7
Wireless 11g MiniPCI Card MP54G User’s Guide Software Installation This section describes the procedures of installing the driver and utility. Follow the instruction step by step to finish the installation. If you use Windows® 98SE/ME, please prepare the Windows® Setup CD at hand before installing the driver; because the system will ask you to insert the Setup CD to copy files during the installation. >>> 3.1 Installing on Windows® 98SE/ME Step 1.
PAGE 8
Wireless 11g MiniPCI Card MP54G User’s Guide Click The installation screen of Setup program Click the Install Software button. Then, the system will detect a new device and start to configure the new device. Click Restart when prompted. After rebooting, the system will search the new device again, click Cancel to continue the installation from the InstallShield Wizard.
PAGE 9
Wireless 11g MiniPCI Card MP54G User’s Guide Step 2. The welcome screen of InstallShield Wizard appears. Click Next. Read and accept the License Agreement; then, click Next. Check this Click Enter the user’s information (User Name, Organization) in the respective fields; then, click Next.