MS-5654 User guide 1
IMPORTANT Satellite signals are required for this product to function in Navigation Mode. There may be occasions within your home or surrounding area when the signal strength is limited and Navigation Mode may not be possible. This is quite normal for products of this type. If you experience difficulty in receiving a signal in your car you may need to use an external antenna (optional).
CONTENTS IMPORTANT.............................................................................................2 Safety........................................................................................................2 The Global Positioning System .......................................................................2 Using Your PND in the Car ..............................................................................2 Prohibited Areas..............................................................
Getting Started This device combines GPS functionality with a photo viewer and Bluetooth Hands-free. Before you begin to install and use this product, please read this manual carefully for fully exploiting the functions of this product. If you experience any problems, go through the user guide before contacting the customer helpline. Position of the controls 1. Power Button 2. SD Card Slot 3. Touch Panel 4. Menu Button 5. Indicator Light* 6. TMC Antenna Jack 7. USB Port 8. Strap Hole 9. Battery Switch 10.
Battery Information The device is integrated with a 1000mAH/ 3.7V Li-polymer battery. It allows the unit to be used for approximately 2 hours, without being connected to a power source. The battery icon which is shown at different point on the display depending on which screen is currently being displayed. The icon indicates the current battery status. : means the battery capacity is full. : means the battery capacity is 80%. : means the battery capacity is 60%. : means the battery capacity is 40%.
Car Adapter When using your PND in the car we recommend that you always use the in-car charger to power the unit, especially on long journeys. Plug the in-car charger into the USB socket on the unit. Plug the other end of the adapter into the car’s cigarette-lighter / 12V DC socket. External Antenna (sold separately) If the GPS receiver fails to acquire a valid signal when mounted in your car it may be due to a heat reflecting coating or heating elements in your windscreen.
Sleep Mode You can use Sleep mode to conserve battery power if the unit is not going to be used for a short while, for example if you have scheduled a stop at a service station. NOTE: if the unit is not to be used for a long period of time, the unit should be switched off by the On/Off switch. Press the Power Button for 3 seconds to put the unit into Sleep Mode. Press the Power button for 3 seconds to wake up the device, the display show the same screen as when the unit was put into sleep mode.
SD Card Installation If you have a SD or MMC memory Card, you may install it to extend the storage capacity of the unit, or to view photos saved on the card. When installing it can only be fitted one way – the wording side facing towards you and the cut-off corner at the bottom as shown. Insert the card and push it in so that it clicks into place. Insert a SD card into the slot, and you will see the below message. If you need to remove the SD card, push the card in and it will eject from the slot.
Connect to PC You can connect the unit to a PC for transferring data. Insert a SD/ MMC card to the card slot; you can then use the unit as a card reader. 1. Power on the unit. 2. Plug B-type end of the supplied USB cable to the mini USB port on the unit, then plug the other end into your computer. 3. The system will try to recognize and connect to the device; the unit display will show the below screen. 4. Once the device has been connected to you will find 2 new USB devices under ”My Computer”.
GPS You have chosen a cutting-edge navigation system. Congratulations! Please enjoy using it. This navigation system leads you straight to your destination, whether you are travelling by car or on foot. You can navigate and plan your route with an easy-to-use and intuitive interface, just by using your finger or the stylus. You can also use this application to plan your trip to suit your personal preferences and interests and to save interesting destinations before you set off on your journey.
Handsfree This device can be linked to a mobile phone as a Bluetooth Hands-free device. After being linked to a mobile phone, you can use the MS-5654 to call and answer the phone without holding your mobile phone. Tap on the Hands-free icon on the Main Menu to enter. To operate the Hands-free function, tap on Bluetooth option to switch it on. You will see a message as below. Remember the passkey for later usage. Then you can see the menu as below.
2. Place the MS-5654 and your phone nearby, and press relative keys on your phone to make it search for new devices. 3. When the searching is complete, you should see a new device named “MS-5654” on the list. 4. Select it from the list, and then your phone will ask you to enter a passkey. Enter 0000 as the pop-up message prompts. Then the MS-5654 is now on the paired list of your phone. 5. Select the MS-5654 and press the required buttons to connect it.
Dial Once a phone is paired and connected to the MS-5654, the Hands-free features of the MS-5654 are now enabled. You can dial from and answer your phone via the MS-5654. Tap on Dial to begin entering a number to dial out, you will see the number pad as below. Tap to enter the phone number you want to call, and then tap on the button. If a number is dialled wrong, tap on once to erase a digit at a time. While dialling, the display will change to the below.
is useful when you are driving a vehicle. button to hang up the call. y Tap on y Tap on / y Tap on button to mute the volume. y Tap on button to adjust the volume. button to mute your voice. When a phone call is received while the MS-5654 and your phone are connected, you will see the below screen appear. The name or number of the caller will be shown on the first line of the display. y Tap on button to answer the call. y Tap on button to hang up the call.
y Tap on a number and then tap on button to call that number again. if you want to delete the number from the list. A message will y Tap on prompt you to confirm. Answered Calls If you have answered a call via the MS-5654, you will see that number on the list. y Tap on a number and then tap on button to call the number back. y Tap on if you want to delete that number from the list. A message will prompt you to confirm.
Travel Kit This device integrates several multimedia programs. You can watch video clips, view photo, and also listen to music. Enter each function to enjoy your media files. Music This device supports MP3, WMA formats. Enter "Music" function to read music list. Note 1: if the music file was saved into the Memory card, enter the Memory card folder to find it. Note 2: if the music file was saved into a specific folder, enter the folder to find it. Note 3: press Menu button to go back main menu.
once to skip and play the next track. Or press it longer to fast-forward y Tap the playback and find the section you need. once to select the repeat mode. y Tap to set Repeat One. Tap Tap to repeat all. to play the files once in regular sequence. Tap y Tap on button to mute the volume. y Tap on / button to adjust the volume.
Video This device supports MPEG4, WMV formats. Enter Video function to watch video clips. Note 1: if the video clip was saved into the Memory card, enter the Memory card folder to find it. Note 2: if the video clip was saved into a specific folder, enter the folder to find it. Note 3: press Menu button to go back main menu. Enter Video function, you will see the figure as below, supported video clips will be listed. You can set to preview the selected clip. If the clip will be played in thumbnail.
Tap on the icon to read the information of the software company. Tap on the icon to view the detail information of the selected clip. Once a clip is selected and being playing, you can tap on the screen to call the function buttons.
y y y y y : Tap on this button to pause the playback. Tap on & to resume to play. : Tap on these buttons to adjust volume. Tap on to mute. : Tap on this button to set playing mode as Random or Ordinal. : Tap on this button to set repeat mode as Repeat Loop, Repeat One, or Repeat List. : Tap on this button to go to the list and find a file to open.
Photo This device supports jpg, bmp, png, gif formats (up to 12MegaPixel file). Enter "Photo" function to see thumbnails for all the photo files. Note: press Menu button to go back main menu. icon on the list, it means that photo is unsupported. Tap on If you see an a photo you want to view, and then you can tap on the left or right triangle to view the previous or next photo. To view pictures (bmp and jpeg formats only) from a SD card: 1) Copy all the pictures you want to view into the SD card.
Slideshow Tap on the button to view the photos show one by one automatically. After tapping on the button, slideshow tool bar will prompt instead. y Tap on button again to stop slideshow. y Tap on button to set the slideshow interval among 2, 3, and 5 seconds. y Tap on button to mute the touch tones. y Tap on button to adjust the touch tones. Rotate Tap on y Tap on the again. y Tap on button to rotate the current photo.
Zoom in Tap on y Tap on the button to zoom in the photo. button to zoom in. y Tap on the button to zoom out. When the photo is zoomed in, you can tap and drag it to view the part you need. y Tap on button to restore the photo. Note: when the zoom in or zoom out limitation is met, the zoom in/ zoom out button will become in gray color and not selectable.
UnitConverter This device integrates a UnitConverter tool. You can use it to easily convert the units of area, distance, speed, temperature, and weight. Note: press Menu button to go back main menu. button to select one option from measurement categories, depends Tap on on the unit you need to convert. 2 2 For example, if you want to convert cm to m , select Area. Then tap on the number buttons to enter value To delete last digit, tap on button. Then tap on button, you can see the converted value.
Currency Converter This device integrates a Currency Converter tool. You can use it to easily convert the currency. Note: press Menu button to go back main menu. The source and target currencies are both selectable. Tap on either button to select the needed source and target currencies. After currencies are selected, you have to set the currency rate. Tap on button to enter Currency Rate setting page. Tap on the number buttons to set the rate of the source and target currencies. To button.
Settings NOTE: You do not need to enter the Settings menu before you start to navigate. Tap on the Settings icon on the Main Menu, the following screen is displayed. To exit this page or any subsequent page, tap on the Exit upper-right corner of the screen or press the menu button. button at the The and button means there are more options available. Tap on one of them to scroll through the list to view the other options.
Display Tap on the Display option to enter display submenu. There are 3 tabs to select and adjust: Brightness, Backlight Timeout, and Screen Calibration. Brightness: With this item, you can change the brightness of the screen. Adjust it darker or brighter by tapping or button. Note: when the minimum or maximum brightness level is met, the level down/ level up button will become grey in colour and is no longer selectable.
Follow the on screen directions to tap on the centre of the cross to calibrate. When the steps are done, you will see the second screen, tap on the screen to save and apply the new calibration settings.
Language Tap to select a language from the list to suit your need. Power Status Enter this option to find out the battery power status. While charging, the status will be in motion, and de-noted “Charging”. If the battery is fully charged and the unit is still on charge, the display will show as the figure below.
Restore This is to allow you to restore the settings back to default values. When necessary, tap on the “Restore” option. button to restore all the settings back to default. After this has been Tap on done, the message “Finished!” will be displayed. Or tap on to cancel and exit.
System Info Tap on ‘System Info’ to access information about the unit and any inserted memory card. There are 2 tabs to select and read: Devices and Storage. Devices: The Devices page shows information about your software version and capacity of the embedded internal memory. Storage: The Storage page tells you the total capacity and free capacity of your storage card (if installed) and the flash disk. If no storage card is installed, the information will show as N/A.
Firmware Upgrade (advanced feature) You can upgrade the firmware of the unit for better performance or/ and more functions. Follow the steps below to do so. Note 1: only advanced users are recommended to operate this feature. Note 2: before upgrading, please make sure that the battery capacity if filled, or power the unit with the car charger to ensure the upgrading will not be corrupted by power failure. Note 3: do not remove the memory card during upgrading! Note 4: please visit www.binatonecarrera.
FM Adjust The device has a FM broadcasting function. Enable this function, you can broadcast audio signal of the device, GPS voice and Music tracks playing on the device, then receive with the FM radio on your car, and output with the speakers. Enter this setting, you can see 2 options. Tap to select Speaker option to let the device output audio by itself. Or tap on FM Transmitter option to set the device broadcast the audio signal to a FM frequency.
Technical Specifications Model Name z MS-5654 Display z z z z z z z z z z z z z z z z z z z z z z z z z z 480 x 272 WQVGA Resolution 4.3” TFT with Touch Panel Centrality A3 372MHz Microsoft Windows CE 5.0 Core Version 1G/2G Onboard NAND Flash ROM 64 MB SDRAM SD Card (Memory type only) Embedded 15x15 mm patch antenna External GPS connector x 1 External TMC connector x 1 3.5mm Stereo Headphone Jack x 1 2.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.