ENGLISH Thank you for purchasing this MICHELE watch. The precision and quality of the quartz movement assures excellent accuracy and never needs winding. The following instructions are provided to help you familiarize yourself with the proper operation and care of your MICHELE watch. To ensure correct use, please read and follow the instructions carefully. All diamonds used on MICHELE watches are genuine diamonds and sourced from non-conflict areas.
AND 3 HANDS MODELS (RONDA 703, 762, 773, 783, 713, 753, 763, 1069) Hour Minute I Hour Seconds Minute I Time Setting I II Seconds Hour Minute II 1. Pull crown out to position II. 2. Turn crown clockwise to rotate hour and minute hands to desired time. 3. Push crown back to position I.
DATE MODELS (RONDA 705, 715, 785) Setting the Time Setting the Date Display 1 Display 2 Display 3 Closed I II III Rotate to set hour & minute hands. Date advances with each 24 hour rotation of hour hand. Rapid correction of date Display 1 Display 2 Display 3 Do not change the date between the hours of 10pm and 2am. This is the time when the movement is in position to carry out the automatic date change, and any interference may cause damage to the movement.
CHRONOGRAPH MODELS (ETA 251) 1/10 Second Timer 60 Seconds Timer Pusher A I 30 Minutes Timer II III Minute Hand Pusher B Second Hand Hour Hand Date Indicator Display 1 Display 2 4 Crown (Position I, II, III)
Zero Reset Set the hand of the 60 seconds timer to zero I II III Crown Set the hand of the 30 minutes timer to zero Set the hand of the 1/10 second timer to zero NOTE: To reset the timer hands (60 seconds hand, 30 minutes hand and 1/10 seconds hand) press Pusher A or B. Each time you press the pusher, it will advance the hands by a single unit. If you hold the pusher pressed in for more than 2 seconds, it advances rapidly.
Correction Mode Setting the Time Setting the Date Time Zone Correction A I II Rotate to set hour & minute hands. Date advances with each 24 hour rotation of hour hand. III NOTE: While crown is in position III, the second hand stops rotating. B Time zone correction Timing Mode Simple Timing Function WARNING: Before starting the timer, put back the chronograph hands to their original positions. If necessary, see diagram titled “Zero Reset.
Timing Mode Split-time or Intermediate Time Function START A I 1 A I Crown in position l B A I B B 4 SPLIT 2 Read time 2 - 15 minutes - 36 seconds - 8/10 sec. RESTART 5 RESTART A I B 2 SPLIT 1 Read time 1 - 5 minutes - 4 seconds - 6/10 sec. 3 6 STOP Read Last time - 25 minutes - 18 seconds - 4/10 sec.
CHRONOGRAPH MODELS (ETA G10, G15) Minute Hand Pusher A I II III Hour Hand Second Hand Crown (Position I, II, III) Pusher B Date Indicator Setting the Time 1. Pull crown out to position III (the watch stops). 2. Turn crown until you reach correct time. 3. Push crown back into position I. Setting the Date 1. 2. 3. 4. 5. 6. 8 Pull crown out to position II (the watch continues to run). Turn crown until yesterday’s date appears. Pull crown out to position III (the watch stops).
Chronograph • The minute counter measures 30 minutes per rotation. • The center stop-second measures 60 seconds per rotation. 1/10 Second Counter Center Stop-second Pusher A I II III Minutes Counter Crown (Position I, II, III) Pusher B PLEASE NOTE: Before using the chronograph functions, please ensure that: - the crown is in position I (= normal position). - the three chronograph hands are precisely at zero position following activation of pusher B.
Chronograph: Intermediate or Interval Timing 1. Press pusher A to start the center stop-second hand. 2. Press pusher B to stop the chronograph. *NOTE: Although the chronograph hands have stopped, the movement continues to record the current timing. 3. Make up the measured time: Press pusher B again and the 3 chronograph hands are quickly advanced to the ongoing measured time. To continue to record intervals, continue to push pusher B. 4. Press pusher A to stop and the final time is displayed. 5.
CHRONOGRAPH MODELS (ISA 8171/204) Second Hand Chronograph Minute Hand Pusher A I II III Crown (Position I, II, III) Chronograph 1/5 Second Hand Moonphase Pusher B Date Indicator Time Setting 1. Pull crown out to position 3. 2. Rotate crown to set correct am/pm time. 3. Return crown to position 1. Date and Moonphase Setting 1. 2. 3. 4. Pull crown out to position 2. Rotate crown clockwise and the set date according to the last full moon. Continue to rotate crown clockwise to set the date.
Split Time 1. 2. 3. 4. Press B while the chronograph is running. Press B again to return to the chronograph. Press A to finalize timing. Press B to reset. Chronograph Zero Reset 1. If either of the chronograph hands is not at the zero (12:00) position, pull crown out to position 2. 2. Press B to reset chronograph minute hand. Each press of B will advance the chronograph minute hand by one increment, or press and hold B for fast advance. 3. Press A to reset chronograph 1/5 second hand.
CHRONOGRAPH MODELS (ISA 8172/220) Pusher A I II III U FRI SA U ED TH Display 1 TH Pusher B Date Indicator T SUN M ED Minute Hand TUE W ON T TUE W ON Second Hand SUN M FRI SA Crown (Position I, II, III) Hour Hand Display 2 Setting the Time 1. Pull crown out to position III (the watch stops). 2. Turn crown until you reach correct time. 3. Push crown back into position I. PLEASE NOTE: The day of the week changes with each 24 hour rotation. Setting the Date 1.
Chronograph • The minute counter measures 30 minutes per rotation. • The center stop-second measures 60 seconds per rotation. Seconds Counter Center Stop-second Pusher A I Minutes Counter III U T ED FRI SA Crown (Position I, II, III) SUN M TUE W ON TH Weekday II Pusher B PLEASE NOTE: Before using the chronograph functions, please ensure that: - The crown is in position I (= normal position) - The two chronograph hands are precisely at zero position following activation of pusher B.
Chronograph: Intermediate or interval timing 1. Press pusher A to start the center stop-second hand. 2. Press pusher B to stop the chronograph. *NOTE: Although the chronograph hands have stopped, the movement continues to record the current timing. 3. Make up the measured time: Press pusher B again and the 2 chronograph hands are quickly advanced to the ongoing measured time. To continue to record intervals, continue to push pusher B. 4. Press pusher A to stop and the final time is displayed. 5.
CHRONOGRAPH MODELS (RONDA 5030.D, 5040.D, 5050.B) 5040.D 5050.B Pusher A I II III Crown (Position I, II, III) Hour Hand I II III Minute Hand Second Hand Pusher B Date Indicator Date Indicator Setting the Time 1. Pull crown out to position III (the watch stops). 2. Turn crown until you reach correct time. 3. Push crown back into position I. Setting the Date 1. 2. 3. 4. Pull crown out to position II (the watch continues to run). Turn crown until yesterday’s date appears.
Chronograph • The minute counter measures 30 minutes per rotation. • The center stop-second measures 60 seconds per rotation. Seconds Counter Center Stop-second Pusher A 5040.D: 30 Minute Counter 5050.
Chronograph: Intermediate or interval timing 1. Press pusher A to start the center stop-second hand. 2. Press pusher B to stop the chronograph. *NOTE: Although the chronograph hands have stopped, the movement continues to record the current timing. 3. Make up the measured time: Press pusher B again and the 3 chronograph hands are quickly advanced to the ongoing measured time. To continue to record intervals, continue to push pusher B. 4. Press pusher A to stop and the final time is displayed. 5.
BATTERY LIFE If your MICHELE timepiece has a chronograph function, you can extend its battery life by ensuring the chronograph function does not run continuously. *NOTE: The chronograph function is in use when the large second hand is in motion. Second Hand STOP A I Crown in position I B RESET 1. To stop the chronograph, press pusher A one time. 2. To reset the large second hand to the 12 position, press pusher B one time. The average battery life when the chronograph is not in use is 2 years.
WATER RESISTANCE All MICHELE timepieces are designed with a minimum water-resistance rating of 5ATM (165ft/50m). See caseback for water resistance rating for traditional watches and Hybrid Smartwatches. The water resistance rating provides guidelines for appropriate water-related exposure to avoid damage to internal watch components. Please see chart for recommended usage guidelines.
TIMEPIECE CARE AND PRECAUTIONS Each MICHELE timepiece is designed and manufactured to exceed the highest of standards. Unlike most other mechanical objects, a watch operates non-stop. In order to ensure optimal performance and longevity from your timepiece, please review the simple guidelines for care and precautions of your new MICHELE timepiece. WATCH CASE AND MOVEMENT CARE Your timepiece should be cleaned with a soft cloth and water only. Do not submerge your timepiece.
Your timepiece should not be affected by magnetic fields generated by household items such as televisions or stereos, but avoidance of other strong electric fields or static electricity, which may interrupt mechanism, is suggested. It is also important to avoid extreme shock or impact. STRAP AND BRACELET CARE At MICHELE we only use first quality materials in making our straps and bracelets. All straps are specifically designed for the watches they fit.
Synthetic Straps and Metal Bracelets Rubber straps, silicon straps and stainless steel bracelets are water-resistant. They are recommended for more active lifestyles. However, please note, they may only be worn for swimming when paired with watch heads which are 10 ATM or greater. Strap and Bracelet Cleaning All MICHELE straps and bracelets should be wiped with a soft cloth. No chemicals or cleaners should be applied to straps.
HOW TO CHANGE STRAPS Push metal tab inward until the pin is released. Repeat this process in reverse to re-insert the new strap. *NOTE: The short side of the strap with the buckle should be attached to the 12 o’clock hour. The long side of the strap should be attached to the 6 o’clock hour.
HOW TO CHANGE BRACELETS Tabs Down Tabs Up Lift up both tabs. Push tabs toward each other to release pin. To re-attach, hold the bracelet against a firm surface, depress the tabs inward, and attach the head.