User's Manual

耳一号声学科技（深圳）有限公司
小米蓝牙项圈耳机 降噪版
V1.1
2019.04.27
连阿婷
选择正确的
方向图标拖
动到图纸里
纹理方向
色相正确、印迹牢固、
套印准确、各色套印
不露杂色，套印误差≤ 0.1mm
印刷+哑膜/水性消光油+模切+贴胶带
110g无光铜+哑油
冷灰11C
白卡覆哑膜：小米专用防刮花哑膜
物料料号: BOPP-YK003
牛卡 材质：秋田牛卡小米专用纸
（示例，具体以产品要求为准）
如有其它特殊要求，请写明
模切走位≤±0.5mm
6934177709371ZBW4474TY23141 LY XQEJ03JY
小米蓝牙项圈耳机 降噪版
Specifications
Model: LYXQEJ03JY
Charging Port: USB Type-C
Wireless Connectivity: Bluetooth 5.0
Bluetooth Profiles: HFP/A2DP/AVRCP
Wireless Range: 10 m (open space without obstacles)
Operation Frequency: 2402 – 2480 MHz
Max. Output Power: 6.37 dBm (Declaration for EU Compliance)
Impedance: 32 Ω
Input: 5 V 1.0 A
Net Weight: 50 g
Charging Time: 2 h
6934177709371ZBW4474TY23141 LY XQEJ03JY
小米藍牙項圈耳機 降噪版
6934177709371ZBW4474TY23141 LY XQEJ03JY
Mi Bluetooth Noise Cancelling Neckband Earphones
USB Type-C Charging Port
Volume +
Volume -
Power Buon
ANC Buon
Indicator/Microphone
Product Overview
User Manual Version: 1.0
Read this manual carefully before use, and retain it for future reference.
Note:
The display of baery and volume is supported on iOS devices only
currently; other devices may not be fully supported.
Please do not use a portable power bank to charge this product.
Illustrations of product, accessories, and user interface in the user
manual are for reference purposes only. The actual product and
functions may vary due to product enhancements.
Functions
Make sure Mi Bluetooth Noise Cancelling Neckband Earphones is
on. Simultaneously press and hold both Volume + and Volume -
buons for 5 seconds to clear connection history. Then it will enter
standby mode and wait for a connection.
Clearing Connection History
When your device is out of wireless range or its Bluetooth function is
disabled, your earphones will enter standby mode. If the connection
is not restored within 5 minutes, the earphones will automatically
turn off.
Connection Lost
How to Use
Press and hold the power buon for 3 seconds, with a blue light on for
1 second to turn on the earphones. It is ready to be connected when
turned on for the first time.
Turning On
Press and hold the power buon for 5 seconds, with a red light on
for 1 second to turn off the earphones.
Turning Off
Note:
Charging Mi Bluetooth Noise Cancelling Neckband Earphones when
it is on, your earphones will automatically turn off and enter the
charging mode.
Note:
When Mi Bluetooth Noise Cancelling Neckband Earphones is on, it
can keep working for 5 hours then turn off automatically with
cancellation enabled and not any Bluetooth device connected.
While in this state, you can reconnect it with Bluetooth device by
pressing the power buon.
The indicator light is red when charging, and goes off when charging
is completed.
Charging
Press: Answer
Press and hold: Decline
Press to switch: ANC on (high level)
ANC on (low level)
ANC off
Incoming Calls Music
Press: Volume -
Press and hold: Next track
Press: Volume +
Press and hold: Previous track
Press × 1: Play/Pause
Press × 2: Voice assistant on
Aer turned on, the earphones will reconnect to the recently paired
Bluetooth device. If there is no connection history, or it fails to
reconnect to any device, your earphones will enter standby mode
and wait for a connection.
Auto Reconnecting
Connecting
Connecting to A New Bluetooth Device
FCC
WEEE
All products bearing this symbol are waste electrical and electronic
equipment (WEEE as in directive 2012/19/EU) which should not be
mixed with unsorted household waste. Instead, you should protect
human health and the environment by handing over your waste
equipment to a designated collection point for the recycling of
waste electrical and electronic equipment, appointed by the
government or local authorities. Correct disposal and recycling will
help prevent potential negative consequences to the environment
and human health. Please contact the installer or local authorities
for more information about the location as well as terms and
conditions of such collection points.
CE
Hereby, Tiinlab declares that the radio equipment type Mi Bluetooth
Noise Cancelling Neckband Earphones is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
hps://www.mi.com/en/service/support/declaration.html
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Do not expose baeries or baery packs to excessive heat such as
sunshine, fire or the like.
Safety Caution
Make sure Mi Bluetooth Noise Cancelling Neckband Earphones is
off. Press and hold the power buon for 3 seconds, with a blue light
on for 1 second to turn it on. Then the blue light is quickly blinking,
indicating it is ready for connecting. Enable the Bluetooth function
on your device, then search for "Mi Bluetooth Neckband Earphones
ANC" to connect. If your device prompts for a password, enter
"0000." Aer successfully pairing, the indicator will turn into slowly
blinking.
Mi Bluetooth Noise Cancelling Neckband User Manual