TM 2.4GHZ CORDLESS TELEPHONE WITH CALL WAITING CALLER ID INSTALLATION AND OPERATING GUIDE IMPORTANT: To receive Caller ID information on incoming telephone calls, you must subscribe to the Caller ID service provided by your local telephone company; there is a fee for this service and it may not be available in all areas.
Warranty NTP-6323 TABLE OF CONTENTS Important Safety Instructions ....................2 MGA 1 Year Limited Warranty This limited warranty sets forth all MGA responsibilities regarding your product. There are no other expressed or implied warranties from MGA Warranty Service Provided If you purchased the telephone new from a retail vendor, MGA warrants the telephone against defects in material and workmanship for a period of one(1) year from the original date of purchase.
IMPORTANT SAFETY INSTRUCTIONS This symbol is to alert you to important operating or servicing instructions that may appear in the user's manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire, or electrical shock. When using this product, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Read and understand all instructions. 2.
TROUBLESHOOTING No dial tone/phone will not dial out. Check that the AC power adapter is plugged into a working AC power outlet. Check all telephone cord connections or try another wall jack. Do a basic reset of the phone: Disconnect the phone from the wall and remove the battery. Leave for 30 minutes and then re-install as instructed by the manual. All the display segments stay on when the handset is in the base. Verify that the battery is properly installed.
FCC REGULATIONS INTERFERENCE INFORMATION: PART 15 OF FCC RULES Some telephone equipment generates and uses radio frequency energy which if not properly installed, may cause interference to radio and television reception. This unit has been tested and found to comply with the limits for a Class B computing device in accordance with the specifications in subpart J of Part 15 of the FCC rules.
OTHER FEATURES BATTERY CAUTIONARY INSTRUCTIONS Using the Handset Finder (PAGE) BATTERIES: CAUTION To reduce the risk of fire or injury to persons, read and follow these instructions: 1. Press PAGE on the base and the phone will beep. PM # NEW If the handset is within range, it will beep until a key is pressed. TOTAL 2. Press any key on the handset, or place the handset in the base to stop the page/find feature.
NTP-6323 PARTS CHECKLIST MESSAGE WAITING If you subscribe to voice mail from the telephone company and if there are voice messages that have been left in your voice mailbox, the display will show "MSG WAITING." MSG AM NEW TOTAL Note: This function requires voice mail subscription from the local telephone company. Furthermore, the local phone company must provide a type of voice mail signaling called "FSK " (Frequency Shift Key).
CALLER ID LOCATION OF CONTROLS AND FEATURES Returning Caller ID Calls You can return calls by using the Caller ID callback feature. 1. Use the call back. to scroll to the call record you wish to PM # NEW TOTAL 2. If the number displayed is not correct (needing 7, 10, or 11 digits), use the key to toggle the number to display the correct number of digits to be dialed. 10.Up and Down button Func PM Press # NEW # NEW 7.Dir button TOTAL Func PM 1.Talk button 3.Scan/Del button 6.
LOCATION OF CONTROLS AND FEATURES Deleting Caller ID Records 1. Talk The Talk key is used to access the telephone line or end a call. 2. Redial Key RE/PA When the phone is idle or off-hook, press RE/PA to redial the last number dialed. RE/PA Is also used to insert a measured pause into a number stored in the phone book. 3.
LOCATION OF CONTROLS AND FEATURES CALLER ID Caller ID with Call Waiting Service In order to use the "Call Waiting Caller ID" service you must subscribe to a telephone company that offers Caller ID service combined with "call waiting" service. Base Use to page a handset(s). When a new call comes in while you are talking, you will hear a notification beep from the handset and the volume is momentarily muted. The new caller's name and phone number, if available, appears on the display.
LOCATION OF CONTROLS AND FEATURES CALLER ID Caller ID Displays Base Bottom View Display shows name and number, time and date of the call. PM # NEW TOTAL Display shows number-only service. Tel Jack PM # NEW TOTAL "PRIVATE" will be shown when a call is received from a blocked number. For privacy reasons, some states allow callers the option to prevent their telephone data from being displayed on the other party's Caller ID display.
CHOOSING A LOCATION CALLER ID Caller ID allows the caller's name and phone number to be shown on the display before you answer the call. In order to use this feature you must first subscribe to Caller ID service with your telephone company. When You Receive a Call # NEW Do the following: Choose the best location Connect the phone Choose the dialing mode 1. When the telephone rings, the caller's name and phone number appears on the display. 2.
TELEPHONE SETUP SPEED DIALING Preferred Calls Connecting the Base You can assign stored numbers as preferred calls. When an incoming call is matched to a stored number designated as preferred, the phone will generate a special ring sound after caller ID information is received. To mark a phone book entry as preferred, add a "#" mark at the beginning of the name during programming or editing.
SPEED DIALING TELEPHONE SETUP Deleting a Stored Number 1. Press T/P Switch Dir 1. Choose the correct dialing mode. . PM # NEW PM 3. Press Del 4. Press Del / Scan # NEW 2. Select the dialing mode Tone or Pulse by setting the switch on the bottom of the base unit. TOTAL 2. Locate the number you wish to delete using . TOTAL . The display will show T/P Switch Note: Changes to the switch position during a call do not tak e effect until the call has ended.
SPEED DIALING BATTERY INSTALLATION To install the cordless Ni-MH handset battery pack: Making Calls From the Phone Book 1. To make a call from the phone book, press 1. Slide the battery pack up into the compartment at the bottom of the handset. Make sure that the end of the battery with the contacts is inserted first. 2. Snap the battery compartment cover into place. 2. Use to dial. 3. Place the handset on the charging cradle. 4.
SPEED DIALING BASIC DISPLAYS Letter Table Key 1st Press 2nd Press 3rd Press 4th Press 5th Press 6th Press 7th Press 8th Press 9th Press 1 Space 1 & ( ) .
BASIC OPERATION Making Calls 1. Pick up the handset and press Talk . SPEED DIALING The NTP-6323 will store up to 64 speed dial numbers in alphabetical order. No duplicate numbers can be stored. Storing Phone Numbers 1. With the handset in the idle state, press Dir . PM # NEW PM 2. Press Flash 2. Wait until you hear a dial tone and then dial the number you wish to dial. The call timer will begin.
BASIC OPERATION SETTINGS Redialing Deleting Message Waiting Indication 1. Press and hold the 2. Press option. 0 Func 1. Press Talk. key to enter the menu. to go to the message waiting programming PM # PM 3. Press Flash TOTAL to reset the message waiting indication. 4. Press and hold to delete the indication. A long beep will sound to confirm. RE/PA 5. Continue with programming or press to the idle screen. Dir 2.
SETTINGS SETTINGS Changing the Pause Time Handset Settings 1. Press and hold the You can change the setting on the handset in the options menu. Access the options menu by pressing and holding the key. Func Dir key There are 10 settings in the options menu which can be changed. You can scroll through the option menu in the listed order by pressing the key. Settings can be reached directly by pressing that number on the keypad. 2. Press option. tuv 8 Func key to enter the menu.
SETTINGS SETTINGS Key Function Setting the Area code tuv 1. Press and hold the 2. Press option. mno Func key to enter the menu. 8 to go to the AREA CODE programming 6 wxyz 9 # 3. Press flashing. Flash to change the setting. "--- will begin 4. Use the dial pad to enter the three digit area code there your phone numbers begins with. 5. When the setting you desire is displayed, press and hold to save the setting. A long beep will sound to confirm the setting has been saved.
SETTINGS SETTINGS Setting the Ringer Level muting the First Ring On or Off 1. Press and hold the 2. Press abc 2 Func key to enter the menu. 1. Press and hold the Func key to enter the menu. to go to the silent programming option. # PM 2. Press 4 flashing. # PM TOTAL 3. Press to change the setting. "On" will begin flashing. TOTAL to change the setting. "HI" will begin Flash 4. Use the key to toggle between On and Off. 3. Use the OFF. key to toggle between HI, LOW, and 4.