Instructions / Assembly

INSTALLATION INSTRUCTIONS FOR FIXTURE
Item#N7338-790 (New. 2022/5/11)
ASSEMBLING THE FIXTURE (FIG. 1)
1. Shut off power at the fuse box or circuit breaker box and remove the old
fixture including the mounting hardware.
2. Carefully unpack your new fixture
and lay out all parts in a clean area. Take
care not to misplace any small parts necessary for installation.
3. Secure rod (P) into spider (L), and tighten until snug. Then place shade
(R)
into rod (P), and tighten with finial (Q)
4. Place shade (K) onto spider (L), and tighten with screws (J).
5. Secure rod (I) into all thread (U) of fixture body (N).
6. Place upper frame (H) onto all thread of rod (I). Make sure upper
decorative cage (H) is on the right position of spider (L). Then t
hread fixture
loop (G) onto all thread of rod (I) until tight.
MOUNTING THE FIXTURE (FIG. 2)
7. Thread all thread (B) into ceiling loop
(D) with lock washer (Y1) and hex nut
(Y2) until snug.
8. Thread other end of all thread (B) into crossbar (A) with lock washer (Y1)
and hex nut (Y2) until snug. Note: The length of all thread into crossbar
may be adjusted if necessary.
9. Take crossbar assembly and mount to ceiling junction box (Not included)
using mounting screws (T) (Size: #8-32N*L1”). The side of crossbar
marked “GND” must face out.
10. Attach quick link (E) to fixture loop (G) and chain (F
). Quick link must be
completely closed when installed. By measuring, determine correct number
of links needed for desired hanging height. Use a pair of chain pliers to
open one end link of chain and discard excess chain. Slip lock collar (S)
,
canopy (C) over chain (F). Attach another quick link (E
) to other end of
chain (F). Raise fixture and attach quick link (E) to ceiling loop (D
), then
close the quick link (E). Carefully lace fixture wires through chain link
s and
pull until tight. Feed wires through lock collar, canopy, ceiling loop and
all
thread, then pull until tight.
CONNECTING THE WIRE (FIG. 3)
11. Connect the electrical wires as shown in Fig. 3, making sure that all wire
connectors are secured. If your junction box has a ground wire (green or
bare copper), connect the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the crossbar using the green screw
provided.
12. Tuck wire connectors neatly into the ceiling junction box.
COMPLETING THE INSTALLATION (FIG. 1)
13. Raise canopy (C) to ceiling and secure with lock collar (S).
14. Install (8) eight candelabra base bulbs (M)
up to 60 watts each or CFL or
LED equivalent (not included) in accordance with the fixture specification.
— D
O NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!)
15. Thread finial of crystal ball (S) onto all thread (O) at the bottom center
of
fixture body (N) until snug.
Your installation is now complete. Return power to the junction box and test
the fixture.
Note:
Illustration (Fig. 1) on this manual is for installation purposes
only. It may or may not be identical to the fixture purchased.
Fig. 3
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
A
VERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
LA-3309E
Fig. 1
Set#A-010
- Crossbar
- Ground Screw
- Mounting Screw *2
Fig. 2
Chain# HCH7472-790
Notice: It is important to use proper chain pliers
(not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
Shade#
-SH7338-1A
-SH7338-2A
Candle cover#
-CCV21055P-790
-CCV21115P-790
Crystal ball# GL7336-C