User Manual

ManualsBrandsMetra ManualsCar & Vehicle ElectronicsMetra 99-6532B Single DIN Dash Kit for 2015 - Jeep Renegade (Black)

METRA. The World’s best kits.

™

metraonline.com

REV. 9/23/2015 INST99-6532B

CAUTION: Metra recommends disconnecting the negative battery

terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your

local Dealership for more information. All accessories, switches,

climate controls panels, and especially air bag indicator lights

must be connected before reconnecting the battery or cycling

the ignition. Also, do not remove the factory radio with the key

in the on position, or the vehicle running. It would be best to

remove the key from the ignition and then wait a few seconds

before removing the factory radio.

Installation instructions for part 99-6532B

• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) White panel clips • E) (4) #8 x 3/8” Phillips screws

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • XSVI-6523-NAV

Antenna Adapter: • 40-EU55 Amplified antenna adapter

• Panel removal tool • Phillips screwdriver

• Torx driver

TOOLS REQUIRED

Jeep Renegade 2015-up

99-6532B

EDC

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DIN radio provision with pocket ...................... 3

Table of Contents

• ISO DIN radio provision with pocket

• Painted to match factory finish

KIT FEATURES

Summary of content (8 pages)

PAGE 1
Installation instructions for part 99-6532B Table of Contents Jeep Renegade 2015-up 99-6532B Dash Disassembly.................................................. 2 Kit Assembly –. ISO DIN radio provision with pocket....................... 3 KIT FEATURES • ISO DIN radio provision with pocket • Painted to match factory finish KIT COMPONENTS • A) Radio trim panel • B) Radio brackets • C) Pocket • D) (4) White panel clips • E) (4) #8 x 3/8” Phillips screws REV.
PAGE 2
99-6532B Dash Disassembly 1. Unclip and remove the trim panel surrounding the factory radio. (Figure A) 2. Remove (4) T-20 Torx Screws securing the radio. (Figure B) 3. Unplug and remove the radio. 4. Cut shaded area at the top of the radio cavity.
PAGE 3
99-6532B Kit Assembly 5. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. ISO DIN radio provision with pocket 1. Attach the (4) supplied white panel clips to the radio housing. (Figure A) 2. Attach the pocket to the radio brackets using (4) supplied #8 x 3/8” Phillips screws.
PAGE 4
Installation instructions for part 99-6532B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6532B Indice Jeep Renegade 2015 y mas 99-6532B Desmontaje del tablero................................................2 Ensamble del kit –. Provisión de radio ISO DIN con cavidad...................
PAGE 6
99-6532B Desmontaje del tablero 1. Desenganche y retire el panel de moldura que rodea el radio de fábrica. (Figura A) 2. Quite los (4) tornillos Torx T-20 que sujetan el radio. (Figura B) 3. Desconecte y quite el radio. 4. Cut área sombreada en la parte superior de la cavidad radio.
PAGE 7
99-6532B Ensamble del kit 5. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente. Provisión de radio ISO DIN con cavidad 1. Una los (4) ganchos blancos del panel suministrados a la carcasa del radio. (Figura A) 2.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-6532B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.