Installation Guide

ManualsBrandsMetra ManualsAudioSilver Honda Fit 2009-2013 Radio Installation Kit

METRA. The World’s best kits.

™

metraonline.com

REV. 3/8/2016 INST95-7877

Installation instructions for part 95-7877

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• ISO DDIN radio provision

• Painted to match factory dash

95-7877S – Silver

95-7877B – Matte Black

• A) Radio housing • B) ISO DDIN brackets • C) ISO DDIN trim plate

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1729

Antenna Adapter: • 40-HD10 • 40-HD11 (with NAV)

• Panel removal tool • Phillips screwdriver • 8mm Socket wrench

TOOLS REQUIRED

Honda Fit 2009-2013

95-7877

Dash Disassembly ..................................................2

Kit Preparation ........................................................ 3

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

B CA

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-7877 Honda Fit 2009-2013 95-7877 Table of Contents Dash Disassembly...................................................2 Kit Preparation.........................................................3 KIT FEATURES • ISO DDIN radio provision • Painted to match factory dash 95-7877S – Silver 95-7877B – Matte Black Kit Assembly –. ISO DDIN radio provision.......................................
PAGE 2
95-7877 Dash Disassembly 1. Unclip and remove the lower center panel below radio. (Figure A) 5. Remove (2) Phillips screws securing the air bag light to the back of the factory radio panel. (Figure E) 2. Remove (1) 8mm bolt facing up behind center panel. Note: Slide the recirculation control lever to FRESH for better access to bolt. (Figure A) 6. Remove (5) Phillips screws securing the A/C vents to the radio panel. (Figure A) 7.
PAGE 3
95-7877 Kit Preparation Kit Assembly ISO DDIN radio provision 1. Secure the hazard switch into the radio housing panel using the factory hardware. (Figure A) 1. Snap the ISO DDIN brackets into the inside edge of the radio housing. (Figure A) 2. Secure the air bag light into the radio housing panel using the factory hardware. (Figure A) 2. Slide the radio into the bracket/ radio housing assembly and secure the radio into the assembly using the screws supplied with the radio. (Figure B) 3.
PAGE 4
Installation instructions for part 95-7877 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-7877 Honda Fit 2009-2013 95-7877 Indice Desmontaje del tablero...........................................2 Preparación del kit..................................................3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Pintura para igualar el tablero de fábrica 95-7877S – Plata 95-7877B – Negro Mate Ensamble del kit –. Provisión de radio ISO DDIN..................................
PAGE 6
95-7877 Desmontaje del tablero 4. Quite (2) tornillos Phillips que sujetan el interruptor de las luces intermitentes a la parte posterior del panel del radio de fábrica. (Figura D) 1. Desenganche y quite el panel central inferior de debajo del radio. (Figura A) 2. Quite (1) perno de 8mm que está orientado hacia arriba detrás del panel central. Nota: Deslice la palanca de control de recirculación a FRESCO para tener un mejor acceso al perno. (Figura A) 3.
PAGE 7
95-7877 Preparación del kit Ensamble del kit 1. Sujete el interruptor de las luces intermitentes al panel de la carcasa del radio con la tornillería de fábrica. (Figura A) Provisión de radio ISO DDIN 2. Sujete la luz de la bolsa de aire al panel de la carcasa del radio con la tornillería de fábrica. (Figura A) 2. Deslice el radio en el soporte/ ensamble de carcasa del radio y sujételo al ensamble con los tornillos suministrados con el radio. (Figura B) 3.
PAGE 8
Instrucciones de instalación para la pieza 95-7877 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.