Installation Guide

ManualsBrandsMetra ManualsAudioStereo Installation Kit For Chevy Malibu Vehicles From 2016-Up (Excluding Malibu Limited)

REV. 3/31/2017 INST95-3019B

INSTALLATION INSTRUCTIONS FOR PART 95-3019B

METRA – The World’s best kits.

metraonline.com

CAUTION!

All accessories, switches, climate controls panels,

and especially air bag indicator lights must be connected before

cycling the ignition. Also, do not remove the factory radio with

the key in the on position, or while the vehicle is running.

• ISO DDIN radio provision

• Painted matte black

• A) Radio trim panel • B) Radio housing • C) Radio brackets • D) (6) #8 x 3/8” Phillips screws

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: Please visit metraonline.com for specific interface options Antenna Adapter: 40-EU55

• Panel removal tool • Phillips screwdriver

• 9/32” socket wrench • Cutting tool

TOOLS REQUIRED

Chevrolet Malibu (excluding Malibu limited) 2016-up

95-3019B

Table of Contents

A B C D

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 95-3019B Chevrolet Malibu (excluding Malibu limited) 2016-up 95-3019B Table of Contents Dash Disassembly.................................................. 2 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN radio provision • Painted matte black KIT COMPONENTS • A) Radio trim panel • B) Radio housing • C) Radio brackets • D) (6) #8 x 3/8” Phillips screws REV.
PAGE 2
95-3019B Dash Disassembly 1. Unclip and remove the small trim panel above the factory radio display, and then remove (2) 9/32” screws exposed. (Figure A) 2. Unclip and remove the trim panel below the climate controls that extend across the dash, and above the glove box. (Figure B) 3. Unclip and remove the climate controls. (Figure C) 4. Inside a small cavity located behind the climate controls, remove (2) 9/32” screws facing up that are securing the radio assembly.
PAGE 3
95-3019B Kit Assembly ISO DDIN radio provision 1. Secure the radio brackets to the radio using the screws supplied with the radio. (Figure A) 2. Slide the radio/bracket/assembly in between the radio trim panel and the radio housing and secure with the (6) #8 x 3/8” Phillips screws provided. (Figure B) 3. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS.
PAGE 4
INSTALLATION INSTRUCTIONS FOR PART 95-3019B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 95-3019B Chevrolet Malibu (excluyendo limited Malibu) 2016 y mas 95-3019B Indice Desmontaje del tablero.......................................... 2 Ensamble del kit –. Provisión de radio ISO DDIN.................................. 3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Pintura negro mate COMPONENTES DEL KIT • A) Panel de moldura de radio • B) Carcasa del radio • C) Soportes del radio • D) (6) #8 x 3/8” Tornillos de Phillips REV.
PAGE 6
95-3019B Desmontaje del tablero 1. Suelte y retire el pequeño panel de moldura arriba de la pantalla de la radio de fábrica, y luego quite (2) 9/32 “tornillos expuestos. (Figura A) 2. Desenganche y quite el panel de la moldura de debajo de los controles de clima se extendió a través del tablero, y arriba de la guantera. (Figura B) 3. Desenganche y quite el controles del clima. (Figura C) (Figura A) (Figura B) (Figura C) 4.
PAGE 7
95-3019B Ensamble del kit Provisión de radio ISO DDIN 1. Asegure los soportes del radio en la radio con los tornillos suministrados con el radio. (Figura A) 2. Deslice el radio/soporte/ ensamblaje entre el panel de moldura y carcasa del radio y sujételo con los (6) #8 x 3/8” tornillos de Phillips suministrados. (Figura B) 3. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y haga todas las conexiones necesarias al radio.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 95-3019B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.