Owner's Manual

ManualsBrandsMetra ManualsCar & Vehicle ElectronicsMetra 95-8907HG Double DIN Dash Kit for Select 2015-Up Subaru Impreza and Crosstrek Vehicles (Black)

Table Of Contents

Installation Instructions

METRA. The World’s best kits.

™

metraonline.com

REV. 11/3/2015 INST95-8907HG

CAUTION: Metra recommends disconnecting the negative battery

terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your

local Dealership for more information. All accessories, switches,

climate controls panels, and especially air bag indicator lights

must be connected before reconnecting the battery or cycling

the ignition. Also, do not remove the factory radio with the key

in the on position, or the vehicle running. It would be best to

remove the key from the ignition and then wait a few seconds

before removing the factory radio.

Installation instructions for part 95-8907HG

• ISO DDIN radio provision

• Painted two-tone silver and gloss black

• A) Radio trim panel • B) Radio brackets • C) (2) Metal speed clips • D) (2) #10 x 3/4” Phillips screws

20;-,(;<9,:

20;*64765,5;:

>0905.(5;,55(*655,*;065: (sold separately)

Wiring Harness: • 70-1761 Antenna Adapter: • 40-LX11

• Panel removal tool • Phillips screwdriver

• 10 mm socket wrench and long extension

;663:9,8<09,+

Subaru Impreza and Crosstrek 2015-up

95-8907HG

Dash Disassembly ..............................................2-5

Kit Assembly

– ISO DDIN radio provision ...................................... 6

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-8907HG Subaru Impreza and Crosstrek 2015-up 95-8907HG Table of Contents Dash Disassembly ..............................................2-5 Kit Assembly – ISO DDIN radio provision ...................................... 6 20; -,(;<9,: • ISO DDIN radio provision • Painted two-tone silver and gloss black REV. 11/3/2015 INST95-8907HG 20; *64765,5;: • A) Radio trim panel • B) Radio brackets • C) (2) Metal speed clips • D) (2) #10 x 3/4” Phillips screws A B C D >0905.
PAGE 2
95-8907HG Dash Disassembly 1. Unsnap and remove the outside trim panel from the driver’s side dash. (Figure A) 2. Remove (2) Phillips screws from the driver knee trim panel and remove the panel. (Figure B) 3. Remove (2) 10 mm nuts now exposed and lower the driver airbag assembly (no need to disconnect).
PAGE 3
95-8907HG Dash Disassembly 4. Release the glove box retaining cable, squeeze the sides and lower the glove box. (Figure D) 5. On both sides unclip and remove the climate control cables, accessed under the dash on the driver side and through the glove compartment opening on the passenger side. (Be sure to watch where the cables are routed). Note, this step is not necessary in vehicles with automatic climate controls.
PAGE 4
95-8907HG Dash Disassembly 6. Remove (1) 10 mm bolt from lower radio supports on each side of the dash (these will be near where the climate control cables were removed, a long extension will be necessary to reach them). (Figure G, H) 7. Unsnap the vent assembly above the radio and unplug the hazard button.
PAGE 5
95-8907HG Dash Disassembly 8. Remove (2) 10 mm bolts from the top radio mounts. (Figure J) 9. Remove and unplug the radio from the dash. 10. Unscrew the radio brackets and remove the factory climate controls from the radio trim.
PAGE 6
95-8907HG Kit Assembly ISO DDIN radio provision 4. Locate the factory wiring harness and antenna connector in the dash, and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. 1. Attach the factory climate controls to the new radio trim panel using the factory hardware. 2. Slide the (2) provided speed clips onto the lower factory mounting brackets.
PAGE 7
95-8907HG 7
PAGE 8
Installation instructions for part 95-8907HG IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.