User Manual

ManualsBrandsMetra ManualsCar & Vehicle ElectronicsMetra 95-7366B ISO Double DIN Dash Kit for 2016- Kia Sorento (Black)

METRA. The World’s best kits.

™

metraonline.com

REV. 9/21/2015 INST95-7366B

Installation instructions for part 95-7366B

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• Painted scratch resistant black

• A) Radio trim panel • B) Radio brackets

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-7304, HYBL-04

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver • 10mm Socket wrench • Cutting tool

TOOLS REQUIRED

Kia Sorento 2016-up

95-7366B

A B

Dash Disassembly ................................................. 2

Kit Preparation ....................................................... 2

Kit Assembly .......................................................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-7366B Kia Sorento 2016-up 95-7366B Table of Contents Dash Disassembly.................................................. 2 Kit Preparation........................................................ 2 Kit Assembly........................................................... 3 KIT FEATURES • ISO DDIN radio provision • Painted scratch resistant black KIT COMPONENTS • A) Radio trim panel • B) Radio brackets REV.
PAGE 2
95-7366B Dash Disassembly Kit Preparation 1. Unclip and remove the factory radio trim panel including the a/c vents. (Figure A) 1. Cut the marked area in the dash cavity. (Figure A) 2. Remove (4) Phillips screws securing the radio and then remove. (Figure B) 2. Remove (1) 10mm nut holding the area previously cut in step 1 to remove the cut-out area.
PAGE 3
95-7366B Kit Assembly ISO DDIN radio provision 1. Attach the radio brackets to the radio using the screws supplied with the radio. (Figure A) 2. Locate the factory wiring harness and antenna plug in the dash and make all necessary connections to the radio. Metra recommends using the proper mating adapters from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. (Figure A) 3. Secure the completed assembly into the sub-dash using the factory hardware. 4.
PAGE 4
Installation instructions for part 95-7366B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-7366B Kia Sorento 2016 y mas 95-7366B Indice Desmontaje tablero................................................ 2 Preparación del kit................................................. 2 Ensamble del kit..................................................... 3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN • Negro resistente a los arañazos de dolor COMPONENTES DEL KIT • A) Panel de moldura de radio • B) Soportes del radio REV.
PAGE 6
95-7366B Desmontaje tablero Preparación del kit 1. Desenganche y quite panel de moldura del radio de fábrica, incluyendo las rejillas. (Figura A) 1. Corte el área marcada en el cavidad tablero. (Figura A) 2. Quite los (4) tornillos Phillips que sujetan de radio y quite. (Figura B) 2. Retire (1) tuerca de 10mm celebración del área cortada previamente en el paso 1 para eliminar el área de corte.
PAGE 7
95-7366B Ensamble del kit Provisión de radio ISO DDIN 1. Coloque los soportes de radio en el radio con los tornillos que vienen con el radio. (Figura A) 2. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente. (Figura A) 3.
PAGE 8
Instrucciones de instalación para la pieza 95-7366B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.