User Manual

ManualsBrandsMetra ManualsAudio & Video AccessoriesMetra 95-7326 Double DIN Installation Kit for 2007-up Hyundai Elantra Vehicles (Black)

METRA. The World’s best kits.

™

metraonline.com

REV. 10/15/2015 INST95-7326

Installation instructions for part 95-7326

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN radio provision

• A) ISO DDIN trim plate • B) ISO DDIN brackets

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1004 • 70-7303

Antenna Adapter: • Not required

• Panel removal tool • Phillips screwdriver • Cutting tool

TOOLS REQUIRED

Hyundai Elantra 2007-2010

(US Model Only) (Non Radio Delete) (Non Touring Model)

95-7326

A B

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-7326 Hyundai Elantra 2007-2010 Table of Contents (US Model Only) (Non Radio Delete) (Non Touring Model) Dash Disassembly.................................................. 2 95-7326 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN radio provision KIT COMPONENTS • A) ISO DDIN trim plate • B) ISO DDIN brackets REV.
PAGE 2
95-7326 Dash Disassembly 1. Unclip and remove the panel surrounding the radio, including the a/c vents and hazard button. (Figure A) 2. Remove (4) Phillips screws to remove radio.
PAGE 3
95-7326 Kit Assembly ISO DDIN radio provision 1. Carefully cut, and remove the bar in the factory radio trim panel. (Figure A) Note: The smoother the cut, the better the 95-7326 will look in the dash panel. CUT OUT BAR CUT HERE 2. Snap the ISO DDIN brackets into the inside edge of the ISO DDIN trim plate. (Figure B) 3. Slide the radio into the assembly from the rear. Secure the radio to the assembly using the screws supplied with the radio. (Figure C) (Figure B) (Figure A) 4.
PAGE 4
Installation instructions for part 95-7326 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para la pieza 95-7326 Hyundai Elantra 2007-2010 Indice (US sólo modelo) (No radio eliminar) (Modelo para no Touring) Desmontaje tablero................................................ 2 95-7326 Ensamble del kit –. Provisión de radio ISO DDIN.................................. 3 CARACTERÍSTICAS DEL KIT • Provisión de radio ISO DDIN COMPONENTES DEL KIT • A) Placa de moldura ISO DDIN • B) Soportes ISO DDIN REV.
PAGE 6
95-7326 Desmontaje tablero 1. Suelte y retire el panel que rodea la radio, incluyendo las rejillas de a/c y botón de peligro. (Figura A) 2. Retire (4) tornillos Phillips para quitar la radio.
PAGE 7
95-7326 Ensamble del kit Provisión de radio ISO DDIN 1. Con cuidado, y quitar la barra en el panel de moldura del radio de fábrica. (Figura A) Nota: El más suave del corte, mejor será la 95-7326 se verá en el panel del tablero. 2. Coloque a presión los soportes ISO DDIN en el borde interior del placa de la moldura ISO DDIN. (Figura B) 3. Deslice el radio en el ensamble de la parte trasera. Sujételo la radio al la ensamble con los tornillos suministrados con el radio. (Figura C) 4.
PAGE 8
Instrucciones de instalación para la pieza 95-7326 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.