User Manual

ManualsBrandsMetra ManualsCar & Vehicle ElectronicsMetra 95-3528B 2004-06 Pontiac GTO Double-DIN Radio Dash Kit (Black)

METRA. The World’s best kits.

™

metraonline.com

REV. 7/28/2015 INST95-3528

Installation instructions for part 95-3528

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

• ISO DDIN Radio Provision

• 95-3528B - Black

• 95-3528G - Gray

• A) ISO DDIN Brackets • B) ISO DDIN Trim plate

KIT FEATURES

KIT COMPONENTS

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • 70-1784

Antenna Adapter: • 40-VW10

• Phillips Screwdriver • Panel Removal Tool • 86-3528 Radio Removal Keys

TOOLS REQUIRED

Pontiac GTO 2004-2006

95-3528

A B

Dash Disassembly ................................................. 2

Kit Assembly

– ISO DDIN radio provision ...................................... 3

Table of Contents

Summary of content (8 pages)

PAGE 1
Installation instructions for part 95-3528 Pontiac GTO 2004-2006 95-3528 Table of Contents Dash Disassembly.................................................. 2 Kit Assembly –. ISO DDIN radio provision....................................... 3 KIT FEATURES • ISO DDIN Radio Provision • 95-3528B - Black • 95-3528G - Gray KIT COMPONENTS • A) ISO DDIN Brackets • B) ISO DDIN Trim plate REV.
PAGE 2
95-3528 Dash Disassembly 1. Using the radio removal keys, pull the factory radio from the dash and disconnect the wiring. (Figure A) 2. Unsnap and remove the trim panel at the top center of the dash above the A/C vents and remove (4) Phillips screws. (Figure B) 3. Remove (1) Phillips screw from inside lower open storage area where center console and dash meet. (Figure C) 5. Remove (2) Phillips screws exposed at the bottom of the center panel surrounding radio and remove panel. (Figure E) 6.
PAGE 3
95-3528 Kit Assembly ISO DDIN radio provision 1. Attach the ISO DDIN brackets to the radio using screws supplied with the radio. (Figure A) 2. Locate the factory wiring harness and antenna plug in the dash and make all necessary connections to the radio. Metra recommends using the proper mating adapters from Metra and/or AXXESS. Re-connect the negative battery terminal and test the radio for proper operation. (Figure A) 3.
PAGE 4
Installation instructions for part 95-3528 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 5
Instrucciones de instalación para 95-3528 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.
PAGE 6
95-3528 Ensamble del kit Provisión de radio ISO DDIN 1. Coloque los soportes ISO DDIN en el radio con los tornillos que vienen con el radio. (Figura A) 2. Localice el arnés de cableado de fábrica y el conector de la antena en el tablero y haga todas las conexiones necesarias al radio. Metra recomienda que use adaptadores adecuados de acoplamiento de Metra y/o de AXXESS. Vuelva a conectar la terminal negativa de la batería y pruebe el radio para verificar que funcione correctamente (Figura A) 3.
PAGE 7
95-3528 Desmontaje Dash 5. Quite los (2) tornillos Phillips expuestos en la parte inferior del panel central que rodea el radio y quite el panel. (Figura E) 1. Usando las llaves de remoción de radio, jale el radio de fábrica del tablero y desconecte el cableado. (Figura A) 2. Suelte a presión y quite el panel de la moldura de la parte superior central del tablero sobre las rejillas de aire acondicionado y quite (4) tornillos Phillips. (Figura B) 6.
PAGE 8
Instrucciones de instalación para 95-3528 Pontiac GTO 2004-2006 95-3528 Indice Desmontaje Dash.................................................... 2 Ensamble del kit –. Provisión de radio ISO DDIN.................................. 3 CARACTERÍSTICAS • Provisión de radio ISO DDIN • 95-3528B - Negro • 95-3528G - Gris COMPONENTES DEL KIT • A) Placa de moldura ISO DDIN • B) Soportes ISO DDIN REV.