User Manual

ManualsBrandsMetra Electronics ManualsAudio & Video AccessoriesChrysler CAN Amp Turn-On Adapter, MULTI COLOR

Installation instructions for CHTO-01

METRA. The World’s best kits.™ metraonline.com1-800-221-0932

REV. 11/5/2014 INSTCHTO-01

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

• Providesaccessory(12-volt10amp)

• RetainsR.A.P.(retainedaccessorypower)

• Usedinamplified,non-amplifiedsystems,ordigitalamplifiedsystems

• ProvidesNAVoutputs(parkingbrake,reverse,andV.S.S.)

• ASWC-1harnessincluded(ASWC-1soldseparately)

• Adjustablegaincontrolforoverallvolume(onamplifiedsystems)

• Retainsblindspotdetectionsystem(ifequipped)

• Highlevelspeakerinput

• Micro“B”USBupdatable

• Retainsbalanceandfade

KIT FEATURES

•Cuttingtool•Tape•Crimpingtool•Connectors

(example:butt-connectors,bellcaps,etc.)

TOOLS REQUIRED

Chrysler vehicles

2004-2010

CHT O-01

APPLICATIONS

See inside front cover

•CHTO-01Interface•16-pinharnesswith

strippedleads•10-pinharnessto22-pinChrysler

harnesswithstrippedleads•4-pinharnesswith

strippedleads

INTERFACE COMPONENTS

Summary of content (8 pages)

PAGE 1
Installation instructions for CHTO-01 CHTO-01 Chrysler vehicles 2004-2010 APPLICATIONS See inside front cover INTERFACE COMPONENTS • CHTO-01 Interface • 16-pin harness with stripped leads • 10-pin harness to 22-pin Chrysler harness with stripped leads • 4-pin harness with stripped leads TOOLS REQUIRED • Cutting tool • Tape • Crimping tool • Connectors (example: butt-connectors, bell caps, etc.) KIT FEATURES • Provides accessory (12-volt 10 amp) • Retains R.A.P. (retained accessory power) REV.
PAGE 2
CHTO-01 Applications Connections to be made CHRYSLER 300 Aspen 2005-2007 2007 From the 16-pin harness DODGE Caliber Charger Dakota Durango Magnum Ram 1500 Ram 2500/3500 2007-2008 2006-2007 2005-2007 2004-2007 2005-2007 2006-2008 2006-2009 JEEP Commander Compass Grand Cherokee Patriot 2006-2007 2007-2008 2005-2007 2007-2008 MITSUBISHI Raider 2006-2007 • Connect the (2) Red wires to the ignition/accessory wire of the aftermarket radio.
PAGE 3
CHTO-01 Connections to be made • Connect the Green wire to the radio’s left rear positive speaker output. Tip: If you are unsure if your vehicle is amplified or not, note that these following wires will only be populated in the factory harness if non-amplified. • Connect the Green/Black wire to the radio’s left rear negative speaker output. • Connect the White wire to the left front positive speaker output of the aftermarket radio.
PAGE 4
Installation instructions for CHTO-01 Installing the CHTO-01 • With all connections completed to the aftermarket radio, plug the 22-pin harness into the vehicles wiring harness. • Reconnect the negative battery terminal. • Cycle the key, by turning the ignition on for 30 seconds. Then off and on again to test the radio. Testing the CHTO-01 • Turn the ignition on if not already, and then turn the radio on to verify that the radio works. Check balance and fader controls for proper operation.
PAGE 5
Instrucciones de instalación para CHTO-01 CHTO-01 COMPONENTES DE LA INTERFASE • Interfase CHTO-01 • Arnés de 16 pins con conectores pelados • Arnés de 10 pins a arnés Chrysler de 22 pins con conectores pelados • Arnés de 4 pins con conectores pelados Vehículos Chrysler 2004-2010 APLICACIONES Lista de aplicaciones dentro HERRAMIENTAS REQUERIDAS • Cortador • Pelacables • Cinta • Conectores (p. ej., conectores a tope, tapas acampanadas, etc.
PAGE 6
CHTO-01 Aplicaciones Conexiones que se deben hacer CHRYSLER 300 Aspen 2005-2007 2007 DODGE Caliber Charger Dakota Durango Magnum Ram 1500 Ram 2500/3500 2007-2008 2006-2007 2005-2007 2004-2007 2005-2007 2006-2008 2006-2009 JEEP Commander Compass Grand Cherokee Patriot 2006-2007 2007-2008 2005-2007 2007-2008 MITSUBISHI Raider 2006-2007 From the 16-pin harness • Conecte los (2) cables rojos al cable de ignición/accesorio del radio de mercado secundario.
PAGE 7
CHTO-01 Conexiones que se deben hacer • Conecte el cable verde con la salida de la bocina positiva izquierda de atrás del radio. • Conecte el cable verde/negro con la salida negativa de la bocina izquierda de atrás del radio. • Conecte el cable púrpura con la salida positiva de la bocina derecha de atrás del radio. • Conecte el cable púrpura/negro con la salida negativa de la bocina derecha de atrás del radio. • Conecte el cable verde/negro con la salida negativa de la bocina izquierda de atrás del radio.
PAGE 8
Instrucciones de instalación para CHTO-01 Instalación del CHTO-01 • Cuando termine de hacer todas las conexiones en el radio de mercado secundario, conecte el arnés de 22 pins en el arnés de cables del vehículo. • Reconecte la terminal de la batería negativa. • Cicle la llave, encendiendo la ignición durante 30 segundos. Después apague y encienda de nuevo para probar el radio. Prueba del CHTO-01 • Prenda la ignición si no lo ha hecho, y después prenda el radio para probar si funciona.