User Manual

ManualsBrandsMetra Electronics ManualsCar & Vehicle ElectronicsToyota Corolla 03 - 08 DIN

METRA. The World’s best kits.

™

metraonline.com1-800-221-0932

REV. 12/3/2013 INST99-8204

CAUTION: Metra recommends disconnecting the

negative battery terminal before beginning any

installation. All accessories, switches, and especially

air bag indicator lights must be plugged in before

reconnecting the battery or cycling the ignition.

NOTE: Refer to the instructions included with the

aftermarket radio.

INSTALLATION INSTRUCTIONS FOR PART 99-8204

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness:

• 70-1761 - Toyota harness 1987-up

• TYTO-01 - LEX/TOY amp interface 2001-up

Antenna Adapter:

• Not required

• Phillips screwdriver • Socket wrench

TOOLS REQUIRED

• DIN radio provision with pocket

• ISO DIN radio provision with pocket

• A) Radio housing • B) Pocket • C) Trim plate • D) Mounting brackets • E) ISO brackets • F) Rear

support bracket • G) (8) #8 x 3/8” Phillips flat head screws • H) (4) #8 x 3/8” Phillips pan head screws

KIT FEATURES

KIT COMPONENTS

Toyota Corolla 2003-2008

99-8204

A B C D

E F G H

Summary of content (8 pages)

PAGE 1
INSTALLATION INSTRUCTIONS FOR PART 99-8204 Toyota Corolla 2003-2008 99-8204 WIRING & ANTENNA CONNECTIONS (sold separately) Wiring Harness: • 70-1761 - Toyota harness 1987-up • TYTO-01 - LEX/TOY amp interface 2001-up Antenna Adapter: • Not required KIT FEATURES • DIN radio provision with pocket • ISO DIN radio provision with pocket TOOLS REQUIRED • Phillips screwdriver • Socket wrench REV.
PAGE 2
99-8204 Dash Disassembly 99-8204 Table of Contents Toyota Corolla 2003-2008 Dash Disassembly 1. Unsnap the gear shifter trim bezel and remove. - Toyota Corolla 2003-2008 .................................................................................. 2 bottom of the factory radio. (Figure A) 2. Remove the center climate control knob and (1) Phillips screw exposed. 5. Remove the factory radio/trim bezel assembly and disconnect the wiring. - DIN radio provision with pocket ........................
PAGE 3
Kit Assembly 99-8204 Radio housing preparation 1. Attach the pocket to the back of the radio housing (by holding the housing upside-down, inserting the right edge of the pocket into place and pushing the rest of the pocket onto the lip) and mount with (2) #8 x 3/8” Phillips pan head screws supplied. DIN radio provision with pocket 2. Secure the mounting brackets to the pocket with (8) #6 x 1/4” Phillip flat head screws supplied. 1.
PAGE 4
INSTALLATION INSTRUCTIONS FOR PART 99-8204 ISO DIN radio provision with pocket 1. Align the holes in the ISO brackets mount the brackets to the radio with the screws supplied with the radio. 2. Slide the radio/bracket assembly into the radio opening until the side clips engage and snap the trim plate over the radio. (Figure A) "A" the negative battery terminal and test the radio for proper operation. 7. Reassemble dash in reverse order of disassembly.
PAGE 5
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-8204 Toyota Corolla 2003-2008 99-8204 CaBLeadO Y COneXiOnes de antena (se venden por separado) Arnés de cableado: • 70-1761 - Toyota arnés 1987 y mas • TYTO-01 - LEX/TOY interfaz amp 2001 y mas Adaptador de antena: • No se requiere CaraCterÍstiCas deL Kit • Provisión de radio DIN con bolsillo • Provisión de radio ISO DIN con bolsillo Herramientas requeridas • Destornillador Phillips • Llave de tubo REV.
PAGE 6
99-8204 Desmontaje del tablero 99-8204 Indice Toyota Corolla 2003-2008 Desmontaje del tablero - Toyota Corolla 2003-2008 .................................................................................. 2 Ensamble del kit - Radio preparación de la vivienda ......................................................................... 3 - Provisión de radio DIN con bolsillo ...................................................................... 3 - Provisión de radio ISO DIN con bolsillo.....................
PAGE 7
Ensamble del kit 99-8204 Radio preparación de la vivienda 1. Coloque el bolsillo en la parte posterior del alojamiento del radio (sosteniendo el alojamiento dado vuelta, introduciendo el borde derecho del bolsillo en su lugar y empujando el resto del bolsillo dentro del reborde), y monte con (2) tornillos Phillips de cabeza de cono achatado n.° 8 x 3/8 in suministrados. Provisión de radio DIN con bolsillo 2. Sujete los soportes de montaje al bolsillo con (8) tornillos Phillips de cabeza plana n.
PAGE 8
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-8204 REV. 12/3/2013 INST99-8204 Provisión de radio ISO DIN con bolsillo 1. Alinee los orificios que se encuentran en los soportes ISO y monte los soportes en la radio con los tornillos suministrados con la unidad. 2. Deslice el conjunto de la radio/del soporte en la abertura del radio hasta que los ganchos laterales se enganchen y coloque a presión la placa de terminación sobre la unidad.