User Manual

ManualsBrandsMetra Electronics ManualsCar & Vehicle ElectronicsMetra 99-6518b 2013 - Up Ram(r) 1500/2500/3500 Single-din Mount Kit

METRA. The World’s best kits.

™

metraonline.com

REV. 7/30/2015 INST99-6518B

Installation instructions for 99-6518B

Table of Contents

CAUTION!

Metra recommends disconnecting the negative bat

tery terminal before beginning any installation, unless the vehicle

manufacturer recommends against so. Please check with your local

Dealership for more information. All accessories, switches, climate

controls panels, and especially air bag indicator lights must be con

nected before reconnecting the battery or cycling the ignition. Also,

do not remove the factory radio with the key in the on position, or the

vehicle running. It would be best to remove the key from the ignition

and then wait a few seconds before removing the factory radio.

KIT COMPONENTS

• ISO DIN radio provision with pocket

• Painted matte black

• Note: Modifications to factory radio cavity

is required for this installation

KIT FEATURES

WIRING & ANTENNA CONNECTIONS (sold separately)

Wiring Harness: • XSVI-6523-NAV • AX-LCD

Antenna Adapter: • 40-EU55

• Panel removal tool • Phillips screwdriver

• 9/32 Socket removal tool

TOOLS REQUIRED

A CB

Dash Disassembly

– Chrysler 200 LX

(with a 3.0” screen) 2015-up ..... 2

– Jeep Cherokee Sport 2014-up ......................3-4

– Ram Trucks 2013-up........................................ 5

Kit Assembly

– ISO DIN radio provision with pocket .................. 6

• A) Radio housing • B) Brackets • C) Pocket • D) (4) #8 x 3/8” Phillips screws

Chrysler 200 LX (with a 3.0” screen) 2015-up

Jeep Cherokee Sport 2014-up

Ram Trucks

(without 8.4 inch touchscreen) 2013-up

99-6518B

Summary of content (16 pages)

PAGE 1
Installation instructions for 99-6518B Chrysler 200 LX (with a 3.0” screen) 2015-up Jeep Cherokee Sport 2014-up Ram Trucks (without 8.4 inch touchscreen) 2013-up 99-6518B KIT FEATURES • ISO DIN radio provision with pocket • Painted matte black • Note: Modifications to factory radio cavity is required for this installation REV. 7/30/2015 INST99-6518B B Dash Disassembly –. Chrysler 200 LX (with a 3.0” screen) 2015-up...... 2 –. Jeep Cherokee Sport 2014-up.......................3-4 –. Ram Trucks 2013-up..
PAGE 2
99-6518B Dash Disassembly Chrysler 200 LX (with a 3.0” screen) 1. Unclip the radio trim bezel from the vehicle. (Figure A) 2. Remove (4) screws securing the radio to the dash, disconnect the connectors attached, and then remove the radio.
PAGE 3
99-6518B Dash Disassembly Jeep Cherokee Sport 2014-up 1. Unclip and remove the climate control panel from the vehicle and put to the side. (Figure A) 2. Remove (2) screws securing the radio trim bezel to the dash. (Figure B) 3. Unclip the radio trim bezel from the vehicle. (Figure C) 4. Remove (4) screws securing the radio to the dash, disconnect the connectors attached, and then remove the radio.
PAGE 4
99-6518B Dash Disassembly Jeep Cherokee Sport 2014-up (Continued) Sub-dash modification: 1. Remove the rubber cover from inside the pocket on top of the dash, and then remove (1) screw exposed. Remove screws Remove sub-dash bracket 2. Remove (2) screws below the radio cavity. (Figure A) 3. From inside the radio cavity, remove (2) screws securing the metal, radio sub-dash bracket, and then discard. (Figure B) (Figure A) 4.
PAGE 5
99-6518B Dash Disassembly Ram (without a 8.4 inch touchscreen) 2013-up 1. Remove liner inside tray at the top center of the dash and remove (2) torx screws. (Figure A) 2. Unsnap and remove radio panel. (Figure B) 3. Remove four screws and remove radio. (Figure C) 4. The factory rear support will need to be cut or removed to allow space for a new radio. The bottom section can be removed with two cuts at the bottom corners.
PAGE 6
99-6518B Kit Assembly ISO DIN radio provision Note: For proper orientation, the locating tabs on the radio housing are more to the top of the kit than bottom. (Figure A) 1. Rotate the brackets into the radio housing. (Figure B) 2. Mount the Pocket inside the brackets using the supplied #8 x 3/8” screws. (Figure C) 3. Slide the radio into the bracket/ pocket/ radio housing assembly and secure using the screws supplied with the radio. (Figure D) 4.
PAGE 7
99-6518B Notes 7
PAGE 8
Installation instructions for 99-6518B IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. Please have the vehicle apart and ready to perform troubleshooting steps before calling. KNOWLEDGE IS POWER REV.
PAGE 9
Instrucciones de instalación para 99-6518B Chrysler 200 LX (con pantalla de 3.0”) 2015 y mas Jeep Cherokee Sport 2014 y mas Ram Trucks (sin pantalla táctil de 8.4) 2013 y mas 99-6518B CARACTERÍSTICAS • Provisión de radio ISO DIN con cavidad • Pintura negro mate • Nota: Se requieren modificaciones a la cavidad del radio de fábrica para esta instalación. REV. 7/30/2015 INST99-6518B B C Desmontaje Dash –. Chrysler 200 LX (con pantalla de 3.0”) 2015 y mas.2 –. Jeep Cherokee Sport 2014 y mas...............
PAGE 10
99-6518B Desmontaje Dash Chrysler 200 LX (con pantalla de 3.0”) 1. Desenganche el bisel de la moldura del radio del vehículo. (Figura A) 2. Retire los (4) tornillos que sujetan el radio a tablero, desconecte los conectores unidos y luego quite el radio.
PAGE 11
99-6518B Desmontaje Dash Jeep Cherokee Sport 2014 y mas 1. Desenganche y quite el panel del control del clima del vehículo y póngalo a un lado. (Figura A) 2. Quite los (2) tornillos que sujetan el bisel de la moldura del radio al tablero. (Figura B) 3. Desenganche el bisel de la moldura del radio del vehículo. (Figura C) 4. Retire los (4) tornillos que sujetan el radio a tablero, desconecte los conectores unidos y luego quite el radio.
PAGE 12
99-6518B Desmontaje Dash Jeep Cherokee Sport 2014 y mas (Continúa) Modificación al sub tablero: 1. Quite la cubierta de goma de la parte interior de la cavidad arriba del tablero, luego retire (1) tornillo que queda expuesto. Quite los tornillos Quite el soporte del sub tablero 2. Quite (2) tornillos debajo de la cavidad del radio. (Figura A) 3. Desde el interior de la cavidad del radio, quite los (2) tornillos que sujetan el soporte metálico en el sub tablero y luego deséchelo.
PAGE 13
99-6518B Desmontaje Dash Ram (sin pantalla táctil de 8.4) 2013 y mas 1. Quite el forro interior de la charola en la parte superior central del tablero y quite los (2) tornillos torx. (Figura A) 2. Suelte a presión y quite el panel del radio. (Figura B) 3. Quite los cuatro tornillos y quite el radio. (Figura C) 4. El soporte trasero de fábrica deberá cortarse o quitarse para hacer espacio para un nuevo radio. La sección inferior puede quitarse con dos cortes en las esquinas inferiores.
PAGE 14
99-6518B Ensamble del kit Provisión de radio ISO DIN Nota: Para una correcta orientación, las pestañas localizadoras de la carcasa del radio están más cerca de la parte superior del kit que de la parte inferior. (Figura A) 1. Gire los soportes hacia dentro de la carcasa del radio. (Figura B) 2. Monte la cavidad dentro de los soportes usando los tornillos suministrados #8 x 3/8”. (Figura C) 3.
PAGE 15
99-6518B Notas 7
PAGE 16
Instrucciones de instalación para 99-6518B IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente como se indica en las instrucciones. Por favor tenga el vehículo desarmado y listo para ejecutar los pasos de resolución de problemas antes de llamar.