Installation Instructions

ManualsBrandsMetra Electronics ManualsElectronicsReverse parking sensors

Table Of Contents

iBEAMUSA.comiBEAM Vehicle Safety Sytems

REV. 05/22/2020 INSTTE-2PSK

Attention!

When testing the aftermarket

equipment, ensure that all factory equip-

ment is connected before cycling the key to

ignition.

TE-2PSK

INSTALLATION INSTRUCTIONS

#IBEAMSAFETY

Technical Tip............................................................2

Installation ......................................................... 3-5

Calibration ..............................................................6

Wiring digrams and specs ................................4-5

TABLE OF CONTENTS

TOOLS REQUIRED

• Wire stripper

• Tape

• Digital Multi-meter

• Cutter

• Alcohol wipes/cleaning pads

Universal 2 Sensor No Drill

Parking Sensor Kit

Visit iBEAMUSA.com for more detailed informatuon about the product and up-to-date vehicle specific

applications.

Product Features

• 2 sensor parking solution

• No need to drill into the bumper

• Audible 3-zone alerts

• No additional control box needed

• Use for plastic bumpers only

• Easy to install

Part Components

A) 2 Sensors B) Wiring harness C) Accessories

A B C

Summary of content (9 pages)

PAGE 1
TE-2PSK INSTALLATION INSTRUCTIONS #IBEAMSAFETY Universal 2 Sensor No Drill Parking Sensor Kit Visit iBEAMUSA.com for more detailed informatuon about the product and up-to-date vehicle specific applications. TABLE OF CONTENTS Technical Tip............................................................2 Installation.......................................................... 3-5 Calibration...............................................................6 Wiring digrams and specs.................................
PAGE 2
TECHNICAL TIP Installation NOTE: This installation may require the removing of the bumper to get the proper sensor alignment. 1. Before removing of the bumper (if it is needed) iBEAM suggests measuring the placement of the sensors on the outside of the bumper with the provided ruler and painters tape. 2. Tape off the vertical mounting location 15-24 inches from the ground. Find the flatest surface possible. (Figure A.1) 3. Find the center of the bumper.
PAGE 3
INSTALLATION Camera Installation 1. Mount the camera with either the surface mount or the license plate mount. If wanting the surface mount, the two small screws will need to be removed to remove the license plate mount and replace with surface mount. 2. Remove the tail light from the vehicle to allow access to the light bulbs wiring. (If help is needed, review the vehicles owners manual section on replacing the tail light bulbs.) (Figure A) 3. Find the wiring that connects to the reverse bulb.
PAGE 4
INSTALLATION Mounting of Sensors (Figure A) NOTE: This installation may require the removing of the bumper to get the proper sensor alignment. 1. Using the painters tape on the outside of the bumper as a guide, re-measure the desired sensor location on the inside of the bumper. • 10-20 inches from the bumper center • 15-24 inches from the ground 1 NOTE: Measurements do depend on the vehicles itself. There is a 4 inch tolerance on the measurements listed, but measurements can vary by vehicle.
PAGE 5
INSTALLATION Running the wiring 1. 2. 3. 4. 5. Carefully find a safe location to run the wires along the bumper or underside of the bumper on the vehile. Use zip ties to secure the wiring to the vehicle. Please keep away from moving parts and anything that would cause too much heat near the wiring. (Figure A) Find a suitable location to gain access to the inside of the vehicle. Mount the Audible buzzer inside the vehicle in a good loction that the driver will hear the alerts clearly.
PAGE 6
CALIBRATION Calibration 1. Complete the installation, put the bumper back in place, make sure power and groung are connected and the buzzer is plugged in. Connect the provided push button to the harness near the buzzer connection. 2. Check power up and make sure there are no moving object within 3 feet of the rear of the vehicle. (Figure A) 3. Press and hold the calibration button for more than 3 seconds to activate the parking sensor system. You should hear two continuous beeps.
PAGE 7
WIRING DIAGRAM AND SPECS 77 gHZ sensors 5 FT Buzzer 3 in RED - Acc./reverse Ground - Chassis ground Calibration button 40 in 5.5 FT Configuration Dual sensors Operating Freq. 77-81Ghz Active condition Field of view (Horz) Speed < 10km/h and reverse gear 144 degrees Alert range 3.2 FT max Weight per sensor 16g Dims per sensor 64.8 x 47.4 x 21.7 mm Operation/storage temp - 40 to 85 C Power consumption 200 mA @ 12 VDC Water resistant IP67 Voltage range 8 - 18V REV.
PAGE 8
TE-2PSK INSTALLATION INSTRUCTIONS #IBEAMSAFETY Having difficulties? We’re here to help. Contact our Tech Support line at: 386-257-1187 Or via email at: techsupport@metra-autosound.com Tech Support Hours (Eastern Standard Time) Monday - Friday: 9:00 AM - 7:00 PM Saturday: 10:00 AM - 7:00 PM Sunday: 10:00 AM - 4:00 PM ® KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry. Log onto www.
PAGE 9
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.