Instruction Manual

ManualsBrandsMeteor ManualsAudioProMover P64

P64 MOVING YOKE

USER MANUAL / OPERATION INSTRUCTION

Thank you for purchasing this truly unique

ProMover P64 MOVING YOKE FIXTURE

ProMover P64 MOVING YOKE FIXTUREProMover P64 MOVING YOKE FIXTURE

ProMover P64 MOVING YOKE FIXTURE

from

METEOR Inc.

It is a fixture that is steadily getting more and more recognition and gaining popularity in the Theatrical Lighting Industry

as a “must have unit”. It was first introduced at the Orlando 2005 LDI show. The simplicity of the fixture is one of its truly

unique qualities. The efficiency and accuracy is the other two main features. The ProMover HPL 575 is capable of using

a variety of different lenses, depending on your specific needs, shapes and angles.

FEATURES:

4 or 6 channels of DMX

Built in Dimmer - controlled via DMX – full range

2 Variable Fans speeds via DMX

8 or 16 bit Resolution- Pan and Tilt

Uses the Any 500w or 1000w PAR 64 LAMP

LCD Display for DMX setting.

Various on board setting routines

Normal or Inverted Digital LCD Readout

Blue LED DMX signal input indicator

Flight Case – (optional –only available with 4-pack deal)

DMX CHANNELS:

Channel 1 – DIMMER – Built in to Channel 1. From 10 to 250 as a variable brightness to

FAN SPEEDS – Variable speeds from 0 – 126 (full speed)

Channel 2 –

STROBE / FLASH – The lamp will now be able to strobe / flash as you increase the

DMX value (0 – 255)

Channel 3 –

PAN

Channel 4 –

TILT

Channel 5 –

FINE ADJUST PAN – (16 BIT - if desired)

Channel 6

–

FINE ADJUST TILT - (16 BIT

– if desired

)

SAFTY FEATURES:

• Lamp change accessibility has been made so that it will be easier to replace a blown or broken lamp

• Wire mesh added to prevent lamp from falling or blown lamp going all over

• Your choice of either 8 bit or 16 bit resolution via LED DISPLAY

• Heavy Duty Flight Case – will now be available in package deals of 4 heads

• DMX Cables can be easily stored inside FLIGHT CASE during shipping:

• Safety cable

LCD SETTING / BUTTONS:

Buttons beneath LCD puts you in a Directive Mode;

M/C – Menu Clear – changes LCD to different functions: set-ups / enables/menu clear.

UP - indicated by an arrow pointing up. Ascends -Raises values

DN - Indicated by an arrow pointing down – descends – lower values

(note: the LCD Display can be either normal or inverted depending on how unit is

mounted. This will be determined if you change it in the NDSP mode)

ENTER - When you get to the function you want to test / use / or demo. Press Enter.

LCD MENU OPTIONS:

ADDR: Setting the starting address (Base address) of all fixtures being used

INIT. As soon as unit is powered up. The LCD screen flashes while it is going through all its

“DMX resets” and Start -up procedures

DISP: Visually normal Digital reading while sitting on floor or Tabletop.

(If you are going to be looking at the LCD while it is on the floor on a table with the light

aiming towards the ceiling.). If “off” display will not be seen

Summary of content (3 pages)

PAGE 1
P64 MOVING YOKE USER MANUAL / OPERATION INSTRUCTION Thank you for purchasing this truly unique ProMover P64 MOVING YOKE FIXTURE from METEOR Inc. It is a fixture that is steadily getting more and more recognition and gaining popularity in the Theatrical Lighting Industry as a “must have unit”. It was first introduced at the Orlando 2005 LDI show. The simplicity of the fixture is one of its truly unique qualities. The efficiency and accuracy is the other two main features.
PAGE 2
Inverted Digital readout - used while unit is mounted on truss or ceiling. (if you are going to be looking at the LCD display while unit is hanging down – it is recommended that you invert the LCD screen read out so you can look at it normal) Test all channels of unit. If you want to test all channels. Press Enter. (LCD changes to read – CH01 – press Enter. Channel 1 (lamp and fan channel) will start to come up in brightness and the fans will increase in speed to cool fixture. Press Black UP button.
PAGE 3
SYSTEM SET-UP / OPERATION: - - Plug in 3-pin XLR cable into base of P64. Daisy chain from one unit to another if need be. Plug fixture(s) into 120v power mains. LCD Screen flashes INIT for a couple of seconds. Blue LED will light if the unit is receiving proper DMX. (No Blue LED, no DMX). Press M/C (Menu change / clear) button until you get to the ADDR screen. Press Enter. Set Base address by using either scroll “up” or “down” buttons.