PROMOVER 250 USER MANUAL / OPERATION INSTRUCTION METEOR-KLS Inc. Alabama Office: www.meteor-kls.com 8000 MADISON PIKE /P.O. BOX 578, MADISON ALA. 35758. (256) 461-8000. FAX: (256) 461-7708 Michigan Office: 3471 BEECHER RD, FLINT, MICHIGAN 48532. Telephone:(810) 230-6600. Fax: (810)230-0066 WWW.METEOR-USA.COM EMAIL: sales@meteor-usa.com 1 WWW.KLS-USA.COM) EMAIL: kls@kls.
PROMOVER 250 DMX Scanner : INTRODUCTION Thank you for having chosen METEOR-KLS PROMOVER 250.You will see you have acquired a powerful and versatile device. It has been designed to be very flexible and user friendly, without compromising effectiveness or professionalism. Unpack your PROMOVER 250. Before you initial start-up, please make sure that there is no damage caused by transportation. Should there be any questions or problems, consult your dealer and do NOT use the device.
- - During the initial start-up some smoke or smell may arise. This is a normal process and does not necessarily mean that the device is defective. Caution: During the operation, the housing becomes very hot. Do not switch the device On and Off in short intervals as this would reduce the lamp's life. Keep away from children and non-qualified users. OPERATING DETERMINATIONS This device is a lighting effect for creating decorative entertainment lighting effects.
USER MANUAL: ProMover 250 DMX-Scanner - Yoke Fixture Keep this manual for future needs! Put it in a place that you can access it if needed. Table of contents: INTRODUCTION: ………………………………….…………… SAFETY INSTRUCTIONS: …………………………… OPERATING DETERMINATIONS: …………………. USER MANUAL INSTRUCTIONS: …………………. DESCRIPTION OF THE DEVICE: …………………………… FEATURES: ……………………………………………. 1 1 2 3 4 OVERVIEW INSTALLATION : ………………………………………………. Installing/Replacing the lamp: …………………………. Lamp adjustment: ………………………………………..
DESCRIPTION OF THE DEVICE: Features: • • • • • • • • • • • • • Innovative DJ-scanner with rotating gobos 7 different, dichroic color filters and white Rainbow-effect with adjustable speed in both directions Gobowheel with 7 rotating gobos, open and blackout Strobe-effect with adjustable speed (1-10 flashes/sec.
Lamp adjustment The lamp holder is aligned at the factory. Due to differences between lamps, fine adjustment may improve light performance. Strike the lamp, open the shutter, and set the dimmer intensity to 100 % and focus the light on a flat surface (wall). Center the hot-spot (the brightest part of the beam) using the 3 adjustment screws "A, B, C". Turn one screw at a time to drag the hot-spot diagonally across the projected image. If you cannot detect a hotspot, adjust the lamp until the light is even.
If you have doubts concerning the safety of a possible installation, do NOT install the device. Before rigging make sure that the installation area can hold a minimum point load of 10 times the device's weight. Master/Slave-operation The master/slave-operation enables that several devices can be synchronized and controlled by one Master device. On the rear panel of the PROMOVER 250 you can find an XLR-jack (DMX Out) and an XLRplug (DMX In), which can be used for connecting several devices.
Building a serial DMX-chain: Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected. Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120-ohm resistor between Signal (-) and Signal (+) into a 3-pin XLR-plug and plug it in the DMXoutput of the last fixture.
DMX- Protocol: CONTROL CHANNEL - 11 DMX Value FEATURES/ ATTRIBUTES CH. 1 COLOR 0-7 8 - 15 16 - 23 24 - 31 32 - 39 40 - 47 48 - 55 56 - 63 64 - 127 128 - 191 192 - 255 WHITE PINK YELLOW BLUE ORANGE GREEN LIGHT PINK LIGHT PURPLE GRADUAL COLOR CHANGE POSITIVE RAINBOW EFFECT w / increasing speed REGRESSIVE RAINBOW w / decreasing speed CH.
FIXTURE LCD: Control Board 8 8 8 8 Mode: select Function up dn md (buttons) 12- 0 Up: increasing key 0 Down - decrease key 0 0 01 d dmx mode:light 1 0 09 d dmx mode: light 2 n 2n n Master mode: sound 5 15 5 Slave mode: slave 1 n 2n n master mode - slow 5 25 5 Slave Mode: slave 2 n 3n n Master mode - stby 5 35 5 Slave Mode: slave 3 0 0 0 HH User time: hour 5 4 5 H5 User time: hour . 1 P Pan Mode-Positive . 1 t Tilt Mode - Positive . 2 P Pan Mode-negative .
3- Tilt Mode Positive: Normal operation: When you press the Tilt 1 and Tilt 2, their starting off point of Tilt will be same.(seldom ever used) 4Tilt Mode Negative: Also same as Pan. (seldom ever used) 5LED Positive Display: When leaving on floor mounted or on test bench (as shown) 6LED Negative Display When you reverse the unit, if you make "LED Negative Display", then it's more convenient to see the display when upside down and mounted.
- The interior of the fixture should be cleaned at least annually using a vacuum cleaner or an air-jet. The dichroic color filters, the gobo-wheel and the internal lenses should be cleaned monthly. To ensure a proper function of the gobo-wheel, we recommend lubrication in sixmonth intervals. Carefully placed quantity of oil must not be excessive in order to avoid that oil runs out when the gobo-wheel rotates. There are no serviceable parts inside the device.