MODEL NO. SRCD1037BT PORTABLE CD PLAYER WITH AM/FM RADIO, BLUETOOTH AND LED DISPLAY OWNER'S MANUAL PLEASE READ BEFORE USING THIS UNIT SYLVANIA is a registered trademark of OSRAM Sylvania Inc. used under license.
1
SAFETY INSTRUNCTIONS Before using the unit, be sure to read all operating instructions carefully. Please note that these are general precautions and may not pertain to your unit. For example, this unit may not have the capability to be connected to an outdoor antenna. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
SAFETY INSTRUNCTIONS 18. OUTDOOR ANTENNA GROUNDING If an outside antenna is connected to the product, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Control Location (Top & Side Views) 4
Control Location (Rear View) Power Connection Power Connection Connecting AC Power Connect the small end of AC cord to the socket at the back of the main unit and insert the plug of AC cord into standard AC wall outlet.
For battery operation, unplug the AC cord from the AC wall outlet first and then remove the AC cord from the socket at the back of the main unit. Caution: There is a danger of explosion if batteries are replaced incorrectly. Replace batteries with the same type and same brand only. When the unit is intended for being unused for a long period of the time, press the POWER button to turn OFF the unit and remove all batteries from the main unit.
Switching On for the first time Plug into AC power or install batteries by following instructions on the previous Power Connection section. The STANDBY indicator willl lit. Press the STANDBY button to turn on the unit. The STANDBY indicator will be lighted off. To turn the unit off, press the STANDBY button again to turn the unit off. Switching between different sources (AM/FM/CD/BLUETOOTH) After turning on the unit, press and toggle FUNCTION switch to select different sound sources.
CD Operation The unit is designed to play normal music CD disc bearing the correct identification logo. If the disc does not confirm tothe standard, it may not be played back properly. Caution: Playback of CD-R / CD-RW may depend on recording conditions. Do not attach a seal or label to either side (the recordable side or the labeled side) of a CDR/ RW disc. It may cause malfunction. Do not load a blank CD-R/ RW disc. It will take over 1 minute to read the disc.
CD Operation-Continued Repeat playback modes (Repeat 1 / Repeat all) Repeat the Current Track During playback, press the REPEAT button once to repeat the current CD track. Repeat All Tracks During playback, press the REPEAT button twice to repeat the entire album. Return to normal playback Press the REPEAT button until NO repeat indicator is displayed. The normal playback will be resumed. Programmed CD playback This unit can be programmed to play up to 20 tracks in CD mode.
Bluetooth Operation Bluetooth Operation If the unit has never been paired with a Bluetooth device before, you need to follow the pairing instructions below to link the SRCD1037BT with your Bluetooth device. • • Press the POWER button to turn on the unit. Press and toggle the FUNCTION button to select Bluetooth mode. The unit will search the paired device with the “BLUETOOTH” Indicator lit. • Press and hold the STOP/PAIR Button for 4~5 seconds.
AUX IN Operation Setting up (AUX IN) connection AUX-IN jack will allow you to connect external music player or external sound source to the main unit. 1. 2. 3. 4. Turn on the unit and slide the function switch to CD/AUX. Plug into a 3.5mm audio cable (not included) into your external music player and connect the other end (3.5mm jack) into the AUX IN jack on the top of the unit.
To make a warranty claim, do not return this product to the store. Please email support@curtiscs.com or call 1-800-968-9853. 90 day Warranty This product is warranted to be free from defects in material and workmanship for a period of ninety (90) days from the date of original purchase. During this period, your exclusive remedy is repair or replacement of this product or component found to be defective, at our option; however, you are responsible for all costs associated with returning the product to us.