©Meshreen DS-MS5168 / info@meshreen.
Content 1. 1.1 2. 2.1 2.2 2.3 2.4 3. 3.1 3.2 4. 4.1 5. 6. 6.1 7. 7.1 8. 9. 10. 11. 12. Introduction Variants 3 Specification Pin configurations Pin Assignment .
1. Introduction The MS5168-001-Myy family is a range of ultra-low power, high performance surface mount modules targeted at IEEE 802.15.4, JenNet-IP, ZigBee Light Link, ZigBee Smart Energy and RF4CE networking applications, enabling users to realize products with minimum time to market and at the lowest cost. They remove the need for expensive and lengthy development of custom RF board designs and test suites.
2. Specification There are differences between modules, the parameters are defined here. VDD=3.3V @ +25°C Typical DC Characteristics M00/03 M04/05 M14 MS5169-M03 Deep sleep current Sleep Current 100nA 0.70uA 100nA 0.70µA 100nA 0.70µA 100nA 0.73µA Radio Transmit current 15.3mA 150mA 150mA 23.
2.1. Pin configurations Figure 1 Pin Configuration (top view) Note that the same basic pin configuration applies for all module designs. However, DIO3(pin9) and DIO2(pin8) are not available on the high power modules. ©Meshreen DS-MS5168 / info@meshreen.
2.2.
2.4. Power Supplies A single power supply pin, 3.3V VDD is provided. 2.5. MS5168-M00/M03 Function Block 2.6. MS5169-M03 Function Block 2.7. MS5168-M04/M05/M14 Function Block ©Meshreen DS-MS5168 / info@meshreen.
3 Electrical Characteristics In most cases, the Electrical Characteristics are the same for both module and chip. They are described in detail in the chip datasheet. Where there are differences, they are detailed below 3.1 Maximum Ratings Exceeding these conditions will result in damage to the device. Parameter Device supply voltage VDD All Pins Storage temperature Min -0.3V -0.3V -40ºC Max 3.6V VDD + 0.3V 150ºC Table 4 Maximum Ratings 3.
4. Outline Drawing Thickness: 2.8mm Four corner of PCB are PCB V-Cut tolerance Figure 3 MS5168-M00 Outline Drawing ©Meshreen DS-MS5168 / info@meshreen.
Thickness: 2.8mm Four corner of PCB are PCB V-Cut tolerance Figure 4 MS5168/MS5169-M03 outline drawing ©Meshreen DS-MS5168 / info@meshreen.
Thickness: 2.8mm Four corner of PCB are PCB V-Cut tolerance Figure 5 MS5168-M04/M05/M14 Outline Drawing ©Meshreen DS-MS5168 / info@meshreen.
4.1. Module PCB Footprint Note 1: All modules have the same footprint Note 2: All Dimensions are mm Figure 6 PCB footprint ©Meshreen DS-MS5168 / info@meshreen.
5. Optimal PCB placement of the MS5168-M00/M05 Module The JN5168-M00/M05 module features an optimized, low cost, integrated, inverted F, printed PCB antenna. The antenna has a vertically polarized near omnidirectional radiation pattern and up to 1.6 dBi of peak gain. The PCB design has been elongated in order to increase the ground plane area which increases the antenna efficiency.
6. Reflow Profile For reflow soldering, it is recommended to follow the reflow profile in figure 6 as a guide, as well as the paste manufacturer’s guidelines on peak flow temperature, soak times, time above liquid and ramp rates. Figure 8 Module Reflow profile reference 6.1.
7. Ordering Information 7.1. ©Meshreen Label example: DS-MS5168 / info@meshreen.
8. Federal Communication Commission Interference Statement Any changes or modifications not expressly approved by the party responsible compliance could void your authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
9. Packing For All models are packing in one size Tray, the Tray dimension is below. The standard packing is base on 500 pcs, use 11 trays which include cover. All modules will packing in vacuum packing bag which include trays, humidity indicator card, desiccant. 9.1. ©Meshreen Net weight and Gross weight Weight MS5168-M00 MS5168-M03 MS5169-M03 MS5168-M04 MS5168-M05 Net Weight T.B.D. T.B.D. T.B.D. 1.92 g T.B.D. Gross Weight with Carton T.B.D. T.B.D. T.B.D. T.B.D. T.B.D.
10. RoHS Compliance MS5168-Mxx modules meet the requirements of Directive 2002/95/EC of the European Parliament and of the Council on the Restriction of Hazardous Substance (RoHS). 11. Disclaimers The contents of this document are subject to change without notice. Meshreen reserves the right to make changes, without notice, in the products, including circuits and/or software, described or contained therein.
