INSTALLATION INSTRUCTIONS This Instruction Manual is a guide for the installation of a netLiNK Controls System. Photographs not to scale.
Before a emp ng to Install the netLiNKTM Controls System, read these instruc ons carefully. Failure to do so may result in damage or malfunc on to the system and will immediately void the warranty. Do Not Wire Hot! NOTE: If the light fixtures are not brand new, completely installed, and fully func onal you must ensure all lamps and ballasts/drivers are in good working condi on, and no electrical problems are present.
Installation Steps & Procedures 1 Base Sta on Install the Base Sta on Install the BFA antenna Connect the proper voltage and record the breaker Ground the ligh ng arrestor Verify that cellular connec on is established Set the lock combina on and record the number Fill out the door decal sheet 2 Pole Mount Nodes Install the Pole Mount Node on predetermined poles [ See site map for reference ] Apply the appropriate s ckers to the fixtures and poles 3 Wall Mount Nodes Install the Wall Mount Node Install t
1 Base Station Installation WARNING: Only use the factory supplied openings of enclosure. DO NOT PENETRATE THE ENCLOSURE. WARRANTY WILL BE VOIDED. ! " # $ %#$& '( )* ( +$+ The maximum distance is 50’.
1 Base Station Installation 1 Mount the Base Sta on (BS) on a wall O * ( ( 6 2 Run the power circuit % ( 8 & enclosure and ensure that the BS has an uninterrupted power supply. 3 Mount the 900MHz BFA antenna to the supplied moun ng hardware bracket and ( P *R installer.
Installation Steps and Procedures Photo Examples Take photographs of all installed components and send all back to your contact you are ready to commissio on the system. commission EXAMPLE EXAMPLE EXAMPLE EXAMPLE EXAMPLE netLiNKControls.com - 214.net.
1 Base Station System Diagram C A A. 900MHz local antenna bulkhead " #$ Antenna. B # %* + # 7 %< = + " < >? J ? ? QX D C. JX C. JXY J Anten Antenna X %J X %J + # 7 Y < Z<\ ^ 7 ?7 ^ 7 QX Q Q J XJ ^ 7 ? ? Z$ E $ _ $ _`{ | J } ~ # G.
1 BFA Antenna Mounting Options {{Y J {{Y " _ * ? JXY J If there is more than one (1) Wireless Node in the system, you will need to install the high gain 900MHz #$ ~ % + Y 7 " _`+ 7 % + 7 _ + "
2 Pole Mount Node Instructions # ( [ ( ' NOTE: # $ ( YZ >Z YZ >Z “LINE IN” is BLACK wire and the associated BLACK with a WHITE STRIPE wire
3 Wall Mount Node Instructions WARNING: DO NOT PENETRATE THE TOP OR SIDES OF THE ENCLOSURE. Doing so will result in permanent damage to the node and void the warranty.
Wall Mount Node Instructions (SMA) Bulkhead d for coax cable enna kit and antenna Normal Open “Electrically Held Contactors” Low voltage ground wire LINE IN 120 VAC NEUTRAL / COMMON GROUND LOAD CH-A (NO) LOAD CH-B (NO) LOAD CH-C (NO) LOAD CH-D (NO) 3 Line In netLiNKControls.com - 214.net.
3 Remote “CT” Diagram 1 1. LED Connector 2 3 2. Channel D “CT” 3. Channel C “CT” 4 5 4. Channel B “CT” 5. Channel A “CT” 6 6. Photocell 7. Low Voltage Only Ground Screw 7 CUT THE CABLE TO THE PROPER LENGTH. J J~? " netLiNKControls.com - 214.net.
3 Remote Antenna Kit (NL-RAK) The Remote Antenna Kit consists of the following components: A - Antenna “L” Bracket (1) B A B - 900MHz Antenna (1) C - 20’ Coax Cable C Step 1 " " 7 " ~ " 7 to the building with the appropriate anchors (Not supplied).
3 Remote Photocell Kit (NL-RPK) B A C The consists of the following components: + ? # )* @ C. Green Phoenix 2 Pin 1 ' V % , , & ' ( { O V 6 ( ( photocell.
