V20200922 Electric Adjustable Height Desk Instruction Manual PARTS DIAGRAM-------------------------------------------------------------- 1 SPECIFICATIONS-------------------------------------------------------------- 2 ASSEMBLY----------------------------------------------------------------------- 3 OPERATION--------------------------------------------------------------------- 5 CONTACT INFORMATION--------------------------------------------------- 8
PARTS DIAGRAM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 COMPONENT Base Lifting Column (Right) Bracket Wiring Channel Frame (Right) Extendable Rod Frame (Left) Transmission Tube Hexagonal Bar Lifting Column (Left) Power Cord Power Adapter Control Box Handset QTY 2 1 2 1 1 1 1 1 1 1 1 1 1 1 NO.
Control Box Connections Motorized Lifting Column Handset Power Cord Control Box SPECIFICATIONS Input Power 110–240V/50–60Hz AC Output Power 24V DC Max. Desktop Height 45 in. (115 cm) Min. Desktop Height 28 in. (70 cm) Load Capacity 220 lb. (100 kg) Max. Speed ¾ in./sec. (20 mm/s) Stroke 17.7 in. (45 cm) Operating Temperature 32–104℉ (0–40℃) Duty Cycle 5 min. on, 18 min.
ASSEMBLY 1 A Loosen and pull the frame (5 & 7) open as shown in Fig. A. Put the two lifting columns (2 & 10) onto B the frame and tighten as shown in Fig. B. 2 Install the bases (1) on the lifting columns with the bolts M6×16 (19). Install the foot pads (25) on the bases. 3 D Connect the transmission tube (8) and tighten as in Fig. C. Adjust the gear box to align with the hexagonal bar (9) as in Fig. D. Insert the hexagonal bar into the transmission tube and gear box. Tighten as in Fig. E.
4 Install the brackets onto the frame with the M6×10 bolts (21). 5 Adjust the width of the frame and fix it to the desktop (27) using the screws (20). Tighten the connecting rod as in Fig. F. Install the wiring channel (4) as shown in Fig. G. Connect the control box (13), handset (14), and motorized lifting column as shown below and in the Parts Diagram.
OPERATION Plug the power cord in. The handset will display 70.0, the current height of the desktop in centimeters. Keys Press to enter the menu settings. ⍓ ⍌ Press & hold to raise the lifting columns. Release to stop. Press & hold to lower the lifting columns. Release to stop. Press once and press a number key to set a height in memory. Press to move the desk to a preset height. Reset ⍌ to the lowest setting and holding continuously resets the desk’s Pressing stored data.
Code Function Choices Notes Press 1Un Unit Selection to change the units displayed. Select to display the desktop’s height in centimeters or to display height in inches. Press to brightness. 2br Brightness Selection 3Fu Sensitivity while Rising 4Fd Sensitivity while Lowering change the display’s Select for medium brightness, for low brightness, or for high brightness. L0–L9 Press to change the desktop’s sensitivity to collision avoidance while rising.
Press to change the maximum and minimum available heights. is the base height of 70 cm and cannot be changed. 5SH Height Range can set a height low limit for the desktop if desired. can set a new upper height limit for the desktop. It must be 115 cm or lower and should be at least 10 cm greater than . Press to toggle between manual (01) automatic (02) height control. ⍓ 6Hc Height Control 01–02 ⍌ In manual mode, the and must be held down to continue movement.
Error Codes HOT RESET Allow 18 min. for the motor to cool. Ensure the ambient temp. does not exceed the desk’s range. If the error is still displayed when the motor is well cooled, unplug the desk and then plug it in again. Follow the reset procedure described above. E01 Remove excessive weight from the desk. Check that all cables are correctly and firmly connected. E06 Follow the reset procedure described above. E07 Remove excessive weight from the desk.