Meri TM INSTALLATION GUIDE
Introduction The Meri™ Smart WiFi Thermostat allows you remotely control and schedule your home’s temperature with ease. It can support most conventional heating and cooling systems with up to 3 heating and 2 cooling stages. Key Features By connecting to the app, you can control your cooling and heating systems from anywhere. Control your temperature. Set energy saving modes. Create timed schedules to automatically set your thermostat and home temperature.
Product Features Main display screen Control buttons Setting controls Wall Plate Wire terminals 3
What’s Included Meri Smart Thermostat Wall Anchors (x2) Screws (x2) Additional tools you’ll need: Screwdriver Pen or pencil (to mark drilling holes) Additional tools you MIGHT need: Needle-nose pliers Wire stripper Drill and drill bit (7/32”) 4 Wire Label Stickers
Compatibility Compatible with most heating, cooling and heat pump systems. Required: 24 VAC power (“C” wire). Does not work with electric baseboard heat (120240V). Does not work with millivolt systems. Android or iOS smart phone, table or device. 2.4GHz (802.11b/g/n) for WiFi connectivity WiFi Requirements The Meri requires 2.4GHz (802.11b/g/n) for WiFi connectivity. This is a standard home WiFi router.
Installation The Meri WiFi Thermostat should be mounted in a suitable location. It is recommended to install the thermostat about 5 ft above the floor and in an open area with good air circulation. Do not install in locations that may affect the temperature reading, such as: - Drafty areas or poorly circulated areas. - Near ducts or appliances that blow hot or cold air. - Concealed pipes and chimneys. - Unheated (uncooled) areas such as an outside wall behind the thermostat.
1. Turn OFF power. Important: You MUST shut off the power at the breaker box that controls your heating/cooling system. 2. Test to make sure the power is off. Sometimes there’s some residual power in the thermostat so it could take up to 5 minutes for your old thermostat to turn completely off. 3. Remove your old thermostat. Most thermostats allow you to just pull off the unit from its wall plate.
5. Take a picture of your current wiring setup. Use your smartphone to take a picture of the wiring and connectors with the letters. You will use this as a reference when connecting to the Meri thermostat. 6. Attach the included label stickers to the wires. Wrap the label stickers around the appropriate wires. This will help when connecting them to the Meri thermostat’s connectors. 7. Disconnect the wires and remove the old wall plate.
and use a pen or pencil to mark the screw holes on the wall. Take off the wall plate and use a 7/32” drill bit to create the hole for the wall anchor, then insert the wall anchors. 9. Bring the wires through the Meri wall plate. Bundle the wires together and through the middle hole of the Meri wall plate. Also check to make sure there is enough exposed wiring (at least ¼ inch) for each wire so they can insert into the wall plate connectors easily.
. Connect your R wire(s). Depending on your heating/cooling system you may have an R, Rh, and/or Rc wire(s). The Meri thermostat can accommodate for these three wires but some configurations require a “jumper” to connect the power. The jumper switch is located on the back of the thermostat as shown in the image below.
To determine the switch position, use the follow chart as a guide.
11. Connect the remaining wires. Match your wires to the appropriate connectors on the wall plate. You will be connecting to the same labeled terminals as your old thermostat connections. You may use the images below as a reference according to your heating/cooling system. Note: Your wire colors mary differ from the images shown below.
1 Stage Heat Pump with Aux and Emer Conventional 2 Stage Heat and Cool 2 Stage Heat Pump with Aux and Emer 2 Stage Heat Pump with Aux 13
12. Attach your Meri WiFi Thermostat. Firmly attach the Meri thermostat to the wall plate. 13. Turn the power back ON. Turn ON the power at the breaker box. 14. Follow on-screen instructions Once the power is back on, there will be a sequence of instructions to connect the WiFi, enter zip code, and app pairing.
© 2016 Momentum Momentum is a registered trademark in the United States. Apple and iPhone are registered trademarks of Apple Inc. Google, Google Play, and Android are trademarks of Google LLC. All other brands and product names are or may be trademarks of their respective owners. Note: Screen shots and procedures described in this manual are subject to change without notice. The latest Momentum User Guide is always available on our website at http://www.momentumcam.com.