System Speedometer and Tachometer Operation Manual THIS MANUAL DESCRIBES THE SMARTCRAFT GAUGE SYSTEMS AVAILABLE FOR YOUR BOAT 2004, Mercury Marine 90-895201 204
0
TABLE OF CONTENTS Basic Operation and Features Auto-Detection Engine Function Master Reset Speedometer Display Screens Tachometer Display Screens Troll Control Warning System Warning Display Screens Tachometer Calibration Quick Cal Calibration CAL 1 Tachometer Calibration CAL 2 Tachometer Calibration Speedometer Calibration Quick Cal Calibration CAL 1 Speedometer Calibration CAL 2 Speedometer Calibration 3 5 6 7 9 11 13 14 18 18 18 22 27 27 27 30 NOTE:This section shows all of the display screens that are
2
BASIC OPERATION AND FEATURES Tachometer 2 1 0 3 4 Speedometer 5 20 6 7 30 40 50 60 10 70 0 80 Power up: Each gauge will power up when the ignition is turned on. Gauges will stay on as long as the ignition is on. Lights: The brightness and contrast are adjustable. Buttons: The MODE button is used for selecting information screens. The “+” and “–” buttons are used for setting engine speed during troll control and setting gauge calibrations.
BASIC OPERATION AND FEATURES Digital Display Screen: Displays the following engine information.
AUTO-DETECTION ENGINE FUNCTION On first time power up of gauge or after a “Master Reset”, gauge will display “Auto detect”. Upon pressing the mode button, gauge will automatically determine engine type. This will preset the data monitoring screens accordingly. The intention is to make initial setup easier. If the gauge shows a warning of “No Starboard Engine” or “Multiple Starboard Engines”, engine location must be properly selected (Port and Stbd) at the engine using a Mercury engine diagnostic tool.
MASTER RESET You can return the gauge back to factory presets through the Master Reset command. IMPORTANT: Performing a master reset will reset the unit back to all factory defaults, thus eliminating any installation calibrations performed during set up of product. – + and TROLL simultaneously for approximately 10 By pressing TROLL seconds (Until the graphic bars “collide”), you will be able to restore the unit back to factory presets.
SPEEDOMETER DISPLAY SCREENS Speedometer 1 30 2 20 10 3 0 40 50 60 70 80 4 5 Continued Next Page NOT ALL SCREENS MAY APPLY TO YOUR ENGINE TYPE. When the ignition is turned on, the speedometer will show the last screen that was displayed before the ignition was turned off. Press MODE to change display screens. You can revert back to the previous screen by pressing and holding MODE for 2 seconds. This will reverse the display rotation. NOTE:Readings can be displayed in English (U.S.) or Metric.
SPEEDOMETER DISPLAY SCREENS Speedometer 6 7 30 20 10 8 0 40 50 60 70 80 9 10 STEERING ANGLE 520 PORT 6. Range – The estimated range is based on boat speed, fuel consumption and fuel remaining in the tank. The numbers displayed indicates an estimate of the distance you can travel with the remaining fuel. Speed input required (Paddle Wheel, Pitot Pressure or GPS). 7. Fuel Economy – The display shows average “AVG” fuel consumption as well as Instantaneous “INST” fuel economy.
TACHOMETER DISPLAY SCREENS Tachometer 1 2 BAT OK TMP 3 PSI 2 4 5 OK 1 6 ENG 3 °F 0 7 4 5 6 PSI WATER PSI NOT ALL SCREENS MAY APPLY TO YOUR ENGINE TYPE. When the ignition is turned on, the tachometer will display the last screen that was displayed before the ignition was turned off. Press MODE to change display screens. You can revert back to the previous screen by pressing and holding MODE for 2 seconds. This will reverse the display rotation. NOTE:Readings can be displayed in English (U.
TACHOMETER DISPLAY SCREENS 7 OIL PSI 10 2 22.3 FUEL USED 22.0 1 0 4 5 6 7 3200 11 12 3 HRS VOLT 8 13.6 9 2.4 Tachometer DEPTH FEET SPEED 25 MPH SEA TEMP 760 7. Oil Pressure – Displays engine oil pressure in units of Psi or Bar. 8. Battery Voltage – Displays voltage level (condition) of battery. Also records the running time of engine. 9. Fuel Flow – Displays engine fuel use in gallons per hour or liters per hour. 10.
TROLL CONTROL Speedometer Tachometer 2 3 4 1 0 TROLL – Actual Speed 5 6 7 0 TROLL – TROLL + Set Speed Actual Speed 80 TROLL + Set Speed TR Basic Operation NOTE:Troll control may not be available on all engine models. NOTE:Troll control min/max range may change depending on engine type. You can set the troll control by using either the tachometer or speedometer. Tachometer will set the speed in RPM and speedometer will set the speed in MPH, Kph or KN.
TROLL CONTROL Tachometer 2 3 4 Speedometer 5 6 1 0 7 0 TROLL – a TROLL – TROLL + Actual Speed 80 Set Speed b TROLL + Actual Speed Set Speed To Set Troll Control 1. With the engine running, shift engine into gear. Set engine speed at idle. 2. Push in the play screen. TROLL + or TROLL – button to bring up the troll control dis- 3. Press MODE to engage (turn on) the troll control. TROLL + – buttons to set the desired speed. Use (+) 4.
WARNING SYSTEM 2 b 3 4 5 1 6 0 7 0 80 a c 2 Alarms Warnings – When a problem is detected, the name of the offending alarm appears on the display (a). If problem can cause immediate engine damage, the Engine Guardian System (b) will respond to the problem by limiting engine power. Immediately reduce throttle speed to idle and refer to the warning messages on the following pages.
WARNING SYSTEM Warning Display Screens When a problem is detected with the engine, the warning display screens will alert the operator to the potential problem. Refer to the Engine Operation, Maintenance and Warranty Manual for explanation of the problem and the correct action to take.
WARNING SYSTEM Warning Display Screens 1 2 2 3 4 5 5 6 1 0 6 7 3 7 4 8 IMPORTANT: Refer to the Engine Operation, Maintenance and Warranty Manual for further explanation of the problem and the correct action to take. 1. OVERHEAT – The engine has overheated. 2. PRESSURE – There is insufficient water pressure in the cooling system. 3. OVERSPEED – Engine speed exceeded the maximum allowable RPM. 4. WATER IN FUEL – Water in the water-separating fuel filter reached the full level. 5.
WARNING SYSTEM Warning Display Screens 9 10 2 1 0 3 4 13 5 6 no starboard engine 7 11 Multiple Starboard Engine 14 15 16 12 9. FAULT-IGNITION – A problem has developed in the ignition system. 10. BATTERY – The electrical system is not charging or the battery charge is low. 11. ENGINE DATA BUS – The data communication link between the tachometer and engine is not connected. 12. FAULT-SENSOR – One of the sensors is not functioning correctly. 13.
WARNING SYSTEM Warning Display Screens 2 17 18 19 3 4 6 1 0 E E 5 7 20 F 21 F 22 17. OIL PRESSURE – There is insufficient oil pressure. 18. LOW FUEL LEVEL – This message serves as a warning that the fuel level in the fuel tank is critically low. You should stop for fuel immediately to avoid running out. 19. LOW OIL LEVEL – OUTBOARD 2 STROKE ONLY – Oil level in the remote oil tank is low. You should stop and refill the oil tank immediately to avoid running out. 20.
TACHOMETER CALIBRATION Quick Cal Calibration Quick Cal – This calibration is for setting lighting and contrast. 1. Press in the MODE and to Quick Cal screen. TROLL + buttons for up to 2 seconds to get 2. Press MODE to advance through the calibration selections. CAL 1 Tachometer Calibration Cal 1 – This calibration lets you turn on and off the system screens. NOTE:Screens may vary depending upon the version of the gauge. + 1.
TACHOMETER CALIBRATION CAL 1 Tachometer Calibration TRIM CALIBRATION [SKIP] [EDIT] Choosing edit allows you to calibrate the gauge to the standard 0–10 unit trim and 11–25 trailer position scale.
TACHOMETER CALIBRATION CAL 1 Tachometer Calibration OIL TEMP SCREEN? [NO] [SAVE] Do you want to turn on the oil temp screen? [YES] OIL PRESS SCREEN? [NO] [SAVE] Do you want to turn on the oil pressure screen? [YES] TRIM AND PSI SCREEN? [NO] [SAVE] Do you want to turn on the trim and water pressure split screen? [YES] WATER PSI SCREEN? [NO] [SAVE] Do you want to turn on the water pressure screen? [YES] TRIM AND RPM SCREEN? [NO] [SAVE] Do you want to turn on the trim and RPM split screen? [YES]
TACHOMETER CALIBRATION CAL 1 Tachometer Calibration VOLT / HOUR SCREEN? [NO] [SAVE] [YES] SPEED / SEA TEMP SCREEN? [NO] [SAVE] [YES] SEA TEMP OFFSET = 0°? [DOWN] [SAVE] [UP] DEPTH SCREEN? [NO] [SAVE] [YES] SIMULATOR MODE? [NO] [SAVE] [YES] CALIBRATION 1 [SAVE] Do you want to turn on the split screen that displays the temperature of the water and the speed of the vessel? This screen allows you to calibrate the display and the water temperature sensor? Do you want to turn on the depth screen
TACHOMETER CALIBRATION CAL 2 Tachometer Calibration CAL 2 – This calibration lets you configure the system sensor inputs. NOTE:Screens may vary depending upon the version of the gauge. + 1. Press in the MODE and TROLL buttons and hold for approximately 10 seconds for calibration2 (Cal2) screen. 2. Press MODE to advance through the calibration selections. There are three methods for calibrating fuel tank level monitoring feature: First: Do nothing. Linear readout based on raw sensor values.
TACHOMETER CALIBRATION CAL 2 Tachometer Calibration FUEL TANK CAPACITY [DOWN] [SAVE] [UP] CALIBRATION FUEL TANK [SKIP] [EDIT] [SKIP] [SAVE] [SAVE] You can choose to have tank at 1/4 and hit SAVE, or hit DFLT and a default value will be entered based on the capacity of the tank. [SAVE] You can choose to have tank at 1/2 and hit SAVE, or hit DFLT and a default value will be entered based on the capacity of the tank.
TACHOMETER CALIBRATION CAL 2 Tachometer Calibration EXTERNAL SENSORS [SKIP] This section lets you enable or disable the following external sensor inputs.
TACHOMETER CALIBRATION CAL 2 Tachometer Calibration TROLL CONTROL? [NO] Is troll control enabled or disabled on this boat? [SAVE] [YES] SPEED OPTION [SKIP] This section lets you configure the following speed sensors. [EDIT] PITOT SENSOR? [NO] [SAVE] [YES] PITOT SENSOR MULTIPLIER [DOWN] [SAVE] [UP] PADDLE SENSOR PULSE FACTOR [DOWN] [SAVE] [UP] PADDLE TO PITOT TRANSITION [DOWN] [SAVE] [UP] Select pitot transducer type. You can choose 100 or 200 PSI.
TACHOMETER CALIBRATION CAL 2 Tachometer Calibration [UP] Lets you electronically configure a depth offset. Entering a negative number gives you a water line offset. A positive number gives you a keel offset. [UP] Lets you enter a depth value. When the depth transducer reads that value or below, the shallow water alarm will sound.
SPEEDOMETER CALIBRATION Quick Cal Calibration Quick Cal – This calibration is for setting lighting and contrast. 1. Press in the MODE and to Quick Cal screen. TROLL + buttons for up to 2 seconds to get 2. Press MODE to advance through the calibration selections. CAL 1 Speedometer Calibration Cal 1 – This calibration lets you turn on and off the system screens. NOTE:Screens may vary depending upon the version of the gauge. + 1.
SPEEDOMETER CALIBRATION CAL 1 Speedometer Calibration CALIBRATION HOUR 12:00 AM [DOWN] [SAVE] [UP] DISPLAY UNITS [DOWN] [SAVE] Lets you change units of measurement between English (standard) or Metric. [UP] SPEED UNITS [DOWN] [SAVE] [UP] STEERING ANG. SCREEN? [NO] [SAVE] [YES] TEMP / CLOCK SCREEN? [NO] [SAVE] [SAVE] Lets you select the units at which speed is displayed. You can choose from MPH (Miles Per Hour), KTS (Knots), or KMH (Kilometers Per Hour).
SPEEDOMETER CALIBRATION Quick Cal Calibration TRIP SCREEN? Do you want to turn on the trip screen? [NO] [YES] [SAVE] FUEL MANAGE SCREEN? [NO] [SAVE] Do you want to turn on the fuel manage screen? [YES] SIMULATOR MODE? [NO] [SAVE] [YES] EXIT? [NO] [YES] [CAL2] Do you want to turn on a simulation mode? (Used for demonstration purposes only).
SPEEDOMETER CALIBRATION CAL 2 Speedometer Calibration CAL 2 – This calibration lets you configure the system sensor inputs. NOTE:Screens may vary depending upon the version of the gauge. + 1. Press in the MODE and TROLL buttons and hold for approximately 10 seconds for calibration2 (Cal2) screen. 2. Press MODE to advance through the calibration selections. EXTERNAL SENSORS [SKIP] This lets you enable or disable external sensor inputs.
SPEEDOMETER CALIBRATION CAL 2 Speedometer Calibration SEA TEMP OFFSET = 0° F [DOWN] [SAVE] This screen allows you to calibrate the display and the water temperature sensor. [UP] TROLL CONTROL? Is troll control enabled on this boat? [NO] [SAVE] [YES] WATER TEMPERATURE ADJUST [DOWN] [SAVE] Adjust water temp transducer to match actual sea water temperature.