MODEL NUMBER: BGBS26 Contents Grill Clearance to Combustible Materials 2 Grill Island Dimensions 3 Hardware Kit 4 Installation Recommendations 5 Installation Step 1-5 WiFi Setup Wiring Diagram 6-8 9-10 11-12 READ ALL INSTRUCTIONS BEFORE INSTALLING AND USING THIS APPLIANCE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE Revision 1.
Clearance To Combustible Materials WARNING: The structure and surrounding objects MUST maintain the specified minimum clearance to combustible materials. Built-in structures constructed of wood or other combustible materials may require the use of the OPTIONAL Built- In Heat Shield Kit to maintain the required clearance to combustible materials. The grill may be supported by either the three support brackets, or the four leveling feet. Please note that there must be at least 3/8” (1.
Built-In Grill Island Dimensions WARNING: See clearance to combustible materials, when designing and constructing a built-in island. Built-In islands must be built to the specifications listed below. The owner and/or builder are responsible for consulting local, county and state building codes for securing any necessary building permits before construction. NOTE: Construction codes vary from locality to locality. NOTE: Dimensions are to the finished surfaces.
HARDWARE COMPONENTS DESCRIPTION/PART NO. 1) Grate Kit VG4409 QTY: 1 2) Savorizer BG2700 1 3) Bracket Bolt DS2311 10 4) Antenna VG9025 1 PICTURE HARDWARE COMPONENTS CONT. DESCRIPTION/PART NO. QTY: 8) Left Mounting Bracket BG8002 1 9) Right Mounting Bracket BG8003 1 10) Rear Mounting Bracket BG8001 PICTURE 1 OPTIONAL 5) #10 Screw (SS) DS2186 2 11) HEAT SHIELD VGBHSK 12) #10 SCREW(BLK) DS2185 6) Concrete Anchor DS2349 2 2 4 TIME REQUIRED 1.
INSTALLATION RECOMMENDATIONS OUTDOOR VENT HOOD Review diagram below for minimum vent hood dimensions. The edge of the hood extends a minimum of 3" past the side edges of the cook surface and 3 1/2" from the back. The bottom of the hood is located 30" 44" above the cook surface. The blower CFM rating is a minimum of 1,200 cubic feet per minute. Overall minimum coverage area for hood is 31 1/2" X 22 1/4".
INSTALLATION STEP 1: UNPACKING Grill requires (2) two people for safe assembly Please note that during shipping some movement may have taken place, so a complete visual inspection is required. Be sure to inspect entire grill after removing the protective shipping carton. Report any damage to your local dealer immediately. Shipping damage is not covered under warranty. Some surfaces may be sharp so wear gloves when assembling.
INSTALLATION STEP 3: BRACKETS Follow the assembly steps listed below, prior to installation of the unit. The unit is mounted by the support brackets (items 8, 9 & 10). Refer to page 4 for item part numbers, descriptions and quantities. 4) Remove the ash/grease drawers from the unit. 5) Fasten the left and right support brackets (items 8 and 9) to the unit using the ten 1/4”-20 stainless steel hex bolts (item 3).
INSTALLATION STEP 5: FINAL ASSEMBLY Refer to page 4 for item part numbers, descriptions and quantities 14) Insert the ash/grease drawer back into the unit. 15) Place Savorizer (item 2) onto the left and right lower brackets found inside the unit. 16) Place the four lower cook grates (item 1) onto the front and rear supports. Place the long cook grate (item 1) onto the left and right upper brackets found inside the unit. Vent holes on the mounting brackets must remain unobstructed.
MEMPHIS WI-FI SET UP GUIDE ON YOUR GRILL CONTROLLER: 1) A Wi-Fi connection can be set up in minutes on your Memphis Wood Fire Grill. First power the grill on pressing the upper left button on the controller, and from the home screen press the lower left button “MENU”, then the bottom right button “DOWN ARROW”, and then the upper right button “WIFI”. 2) The “WIFI” screen on your grill contains everything needed to connect your grill to a WiFi network.
MEMPHIS WI-FI SET UP GUIDE CONTINUED 8) Download our app MEMPHIS GRILLS from the IOS App Store or Google Play Store 9) Enter a valid email into the “CUSTOMER ID” field, and create a password that you will use to login to the app. Then click "Create an Account" this will bring up our cloud providers Terms of Service, click "Accept". You will then receive an email confirmation link at the email used to sign up from Grovestreams who is our cloud provider.
Item # NAME Wire Identification 1x Black Wire, 1x White Wire Snap Disk Leads Extending from Auger Motor 1 Auger Motor Wiring 2 RTD Wiring 1x Orange Wire, 1x Brown Wire 3 Grounding Wire Green Wire 4 Ethernet Cable Black Cable with Ethernet End 5 Igniter Wiring 1x Red Wire, 1x White Wire 6 Fan Wiring 1x Blue Wire w/ 2 spade ends, 1x White Wire w/ 2 spade ends 7 USB Port N/A 8 Meat Probe Wiring 1x Red Wire 1x Black Wire, Wires twisted around each other 9 10 11 12 13 120/240 Select Ju