Rev.
Table of Contents ENG 1. Please read the cautions carefully before using this product. 1, 2 2. Product feature 3 3. Product installation 4 4. Names and operation of control buttons 5, 6 5. OSD MENU Selection and operation 7 6. MENU function 8, 9 7. Utilization message 10 8 Timing guide 11 9. Input signal detail 12 10. Product specification 13 11.
ENG Please read the cautions carefully before using this product Do not scratch the screen of the LCD monitor with sharp materials such as nails and pens. The interior part of the monitor is composed of electric elements. If the monitor is broken, do not try to disassemble it, because it is necessary to contact appropriate technical services in order to have the product repaired. Take care of the LCD monitor so that it is not damaged by the external impact.
Product features ENG ඖGIntroduction Thank you for purchasing our monitor. Our monitor is a high-resolution monitor that has features of electromagnetic wave blocking, reduction in electricity consumption and efficient use of space. This manual has been prepared to help you using this product adequately. It is recommendable to read this manual before using this product. ඖGProduct features GXPGThis product (MV220) has 22-inch flat surface (Color Active Matrix TFT LCD) with pixel size of 0.285 mm (H) x 0.
Product installation ENG ൘ Checking the product Please check if the product contains the following items. If there are items missing, please contact our technical services. 1. TFT LCD monitor 2. User's manual (including product warranty card) 3. AC to DC adaptor 4. Power cable 5. Signal cable (15Pin D-SUB cable) 6. Audio cable ൘ Installation 1. Please, turn on MV220, before connecting any device to it. 2. Connect adaptor cable to DC power-on on the rear side of MV220, then connect power cord to adaptor.
Names and operation of control butto MENU SE LECT ൖ ൘ MODE ENG POWER ൘ Function of the buttons 'MENU' Show the menu screen or makes it disappear, Moreover 'SELECT' Select category within the menu window or excutes automatic screen adjustment. - 'ൖ' / '൘' Moves to the desired category within the menu window or adjusts the value of selected category and adjust sound volume. 'MODE' Changes the modes, the orders being changed are same as below.
Names and operation of control buttons ENG Auto Brightness Control The product offers built-in function that automatically adjusts to optimized brightness depending on the brightness of the area at the vicinity. (At the time of purchase, this is set as On.) * Refer to the screen category of the MENU function for detailed method of use.
OSD MENU Selection and operation ENG You can select the OSD menu in the OSD window using all the control buttons at the bottom of the screen. To change the current settings or adjust them for the desired settings, follow the following steps. MENU W/X SELECT (Open menu screen ) (move to main category) (select main category ) SELECT W/X MENU (Close menu screen) (save set value) (adjust set value) W/X (move to sub category ) SELECT (select sub category) 1.
MENU Function ENG Screen Automatic brightness: Turns automatic brightness function On/Off Brightness adjustment: Adjusts standard value for automatic brightness function (0-100) Horizontal location: Adjusts horizontal location on screen .(0-100) Vertical location: Adjusts vertical location on screen \.(0-100) Modulation: Adjusts focus on the screen.(0-100) Frequency: Adjusts pixel’s horizontal size.(0-100) Automatic screen adjustment: Automatically adjusts screen’s location, modulation and frequency.
ENG 10,20,30,40) Aspect Ratio : Selects display aspect with 4:3. 1680*1050 resolution. Parts of the category are provided in the DVI mode’s screen, color menu.
Explanation of message for utilization ENG Auto Adjustment Appears when automatic screen adjustment is executed on RGB mode. Auto color Adjustment Appears when automatic color Adjustment is executed on RGB mode. Auto Brightness Appears when automatic brightness function is executed. No Signal (RGB, DVI, COMPONENT) Appears when there is no PC input signal Check cable connection . OUT OF FREQUENCY Appears when Video Mode is out of the permissible range.
Timing guide ENG Timing guide This product is a multi-frequency monitor. It functions in horizental frequencies from 30kHz to 80kHz and vertical frequencies from 56Hz to 75Hz. Due to tis design based on microprocessor, It offers the functions of automatic synchronization and automatic size. This monitor is equipped with 12 programmed configurations that are shown in the timing table. The followings are the ten configrations. thj pit }lzh tX ][W [_W Z\UWo¡ ]^o¡ ZWUY[W TVT tY _ZY ]Y[ [`U^o¡
Input signal detail ENG This signal input terminals are for 15Pin D-SUB, DVI-D, Component. Please, connect the cables of each signal to your PC's input signal port. ඖ15Pin D-SUB X Y Z [ \ y n i uGj n ] ^ _ ` XW yGn nGn iGn uGj n XX XY XZ X[ X\ ` XW XX {UtUkUzGGkGXT {UtUkUzGGkGXR {UtUkUzGkGXVZ z {UtUkUzGkGZT {UtUkUzGkGZR RG\}Gw n oGwGk X^ {UtUkUzGGkGWT X_ {UtUkUzGGkGWR X` {UtUkUzGkGWV\ z
Product specifications Product specifications Pixel Pitch Display Color Surface Condition Viewing Angle 22" diagonal viewable screen TFT(Thin Film Transistor) Active matrix panel R, G, B vertical stripe 16,777,216 colors Anti glare coating H/V Contrast ratio 1000 : 1 Brightness 300cd/m Reponse Time 5ms IBM 486, Pentium or PS/2 and compatibles Refresh rate Connectors 1680 x 1050 @ 60Hz for optimal display Input signal Power Voltage / Power Temperature Storage Condition Function 33 F ~ 104 F
Troubleshooting ENG No power. - Flip the power switch ON. The Power LED turns on. - Make sure AC power cord is securely connected to the power jack and to a power outlet. Power on but no screen image. - Make sure the video cable attached with this monitor is tightly secured to the video output port on the back of the computer - Adjust the brightness and contrast. Image is unstable, unfocused. - Use AUTO-TUNE to adjust automatically.
Troubleshooting ENG Control buttons do not work. - Press only one button at a time. When the message of 'out of range' appears. 1. Restart the computer and while it is restarting, press F8 until the Startup menu appears. Then enter to start the computer in 'safe mode'. 2. Right-click the desktop, click Properties, and click Settings. 3. Click Advanced, click Adapter, and then click Adapter Default from the Refresh Rate. 4.
FCC NOTE :This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
